CyberPower CPS600E Bedienungsanleitung

User’s Manual

CPS600E

CyberPower Europe

CyberPower Systems B.V.

Flight Forum 3545, 5657DW Eindhoven, The Netherlands

Tel: +31 (0)40 2348170

Fax: +31 (0)40 2340314

Website: http://eu.cyberpowersystems.com/

E-mail: sales@cyberpower-eu.com

K01-0000186-00

CPS600E

Content

SAFETY AND EMC INSTRUCTIONS ................................... 2

INSTALLING YOUR EPS ...................................................... 4

UNPACKING.........................................................................................4

AUTOMATIC VOLTAGE REGULATOR ...............................................4

HARDWARE INSTALLATION GUIDE...................................................4

BASIC OPERATION .............................................................. 5

DESCRIPTION .....................................................................................5

REPLACING THE BATTERY ................................................ 6

DEFINITIONS FOR ILLUMINATED LCD .............................. 7

EPS STATUS INQUIRY AND FUNCTIONS SETUP ............. 8

GENERAL MODE .................................................................................8

SET-UP MODE .....................................................................................8

FAULT WARNING DISPLAY AND ALARM ........................ 10

TROUBLESHOOTING ......................................................... 11

TECHNICAL SPECIFICATIONS ......................................... 12

CPS600E

SAFETY AND EMC INSTRUCTIONS

This manual contains important safety instructions. Please read and follow all instructions carefully during

installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your Emergency Power System (EPS).

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled

indoor area free of conductive contaminants. (Please see specifications for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery.

There are no serviceable parts inside, except for the battery.

CAUTION! EPS must be connected to an AC power outlet with circuit breaker protection. Do not plug

into an outlet that is not grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before

servicing EPS, replacing the external battery or installing equipment.

CAUTION! To reduce the risk of fire, only connect the EPS to a circuit with 10 amperes maximum

branch circuit over-current protection in accordance with the CE requirement.

CAUTION! The building wiring socket outlet (shockproof socket outlet) must be easily accessible and

close to the EPS.

CAUTION! Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your

equipment) to connect the EPS to the building wiring socket outlet (shockproof socket outlet).

CAUTION! Please use only VDE-tested, CE-marked power cables to connect the loads to the EPS.

CAUTION! When installing the equipment, ensure that the sum of the leakage current of the EPS and the

connected equipment does not exceed 3.5mA.

CAUTION! Do not disconnect the mains cable on the EPS or the building wiring socket outlet

(shockproof socket outlet) during operations since this would remove the protective ground of the EPS

and of all connected loads.

CAUTION! This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!

DO NOT use in any circumstance that would affect operation and safety of any life support equipment,

any medical applications or patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use

with or near an aquarium. Condensation from the aquarium can cause the unit to short out.

DO NOT INSTALL THE EPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR

HEAT!

DO NOT BLOCK OFF VENTILATION OPENINGS IN THE EPS’S HOUSING!

CPS600E

SAFETY:

EN62040-1-1

EMI:

Conducted Emission: IEC/EN 62040-2…Category C2

Radiated Emission: IEC/EN 62040-2……Category C2

Harmonic Current: IEC/EN61000-3-2

Voltage Fluctuations and Flicker: IEC/EN61000-3-3

EMS:

IEC/EN61000-4-2(ESD)

IEC/EN61000-4-3(RS)

IEC/EN61000-4-4(EFT)

IEC/EN61000-4-5(lightning surge)

IEC/EN61000-2-2 (Immunity to low frequency signals)

CPS600E

INSTALLING YOUR EPS

UNPACKING

Inspect the EPS upon receipt. The box should contain the following:

EPS unit x 1; User manual x 1; Input Power Cord x 1; DC Fuse x 2

AUTOMATIC VOLTAGE REGULATOR

Utility power is inconsistent. The EPS increases low voltage to computer safe 220 volts. The EPS

automatically provides battery backup (External battery connection required) if the voltage drops below

170 volts or exceeds 270 volts.

HARDWARE INSTALLATION GUIDE

1.Your new EPS may be used immediately upon receipt. However, recharging the external battery for at

least 8 hours is recommended to ensure that the battery’s maximum charge capacity is achieved. To

recharge the external battery, simply leave the unit plugged into an AC outlet when EPS is ON.

2. DO NOT use with medical or life support equipment. DO NOT use with or near aquariums as

condensation may cause the unit to short out.

3. After connecting the hard wires, plug the EPS into a 2 pole, 3 wire grounded receptacle (wall outlet).

Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service

equipment with large electrical demands (e.g. air conditioner, copier, etc…). The warranty prohibits the

use of extension cords, outlet strips, and surge strips.

4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will

beep once.

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct

this, turn the EPS off and unplug the equipment from the AC outlet. Ensure that the equipment plugged

into the outlet does not exceed the UPS unit’s rated capacity (600VA/420W for CPS600E). If the

rated capacities of the unit are exceeded, an overload condition may occur and cause the UPS unit to

shut down or the input fuse to blow. For more information, refer to the “Troubleshooting” section.

6. To maintain optimum battery charge performance, make the EPS plugged into an AC outlet at all

times.

7. The UPS is designed for horizontal or wall-mount use only. To ensure safety, please follow the

placement directions as shown below.

CPS600E

BASIC OPERATION

DESCRIPTION

1. Power Switch

Used as the master on/off switch for equipment connected to the AC outlet.

2. Power On Indicator

This LED is above the power switch. It illuminates when the utility condition is normal and the AC outlet

is providing power, free of surges and spikes.

3. Multifunction LCD Readout

High resolution and intelligent LCD display shows all the EPS information with icons and messages.

For more information please check the DEFINITIONS FOR ILLUMINATED LCD INDICATORS section.

4. LCD Display Toggle / Selected Switch

Users can monitor EPS status and set up functions using the toggle. The buzzer on/off can also be

controlled by the toggle switch. Please refer to “EPS Status Inquiry and Functions Setup” section for

more details.

5. AC Outlet

The unit has one Schuko type outlet for connected equipment to ensure temporary uninterrupted

operation during a power failure. Max. Output is 6.3A; Max. Output wattage is 420W.

Note! Maximum cord length is 10 meters and the cable O.D. must be 14AWG or greater.

6. AC Inlet

Connect to utility power through the input power cord.

Note：The O.D. of the distribution cables must be 0.75mm or greater.

Input Fuse

The fuse provides optimal overload protection.

Note：The Input Fuse is 6.3A/250V.

7. Black Battery Cable (Negative (-))

Connect black (negative (-)) battery cable to the black (negative (-)) connector on the external battery.

Note: The Battery cable is 10AWG / 4 feet.

8. Red Battery Cable (Positive (+))

Connect red (positive (+)) battery cable to the red (positive (+)) connector on the external battery.

Note: The Battery cable is 10AWG / 4 feet.

9. DC Fuse

The fuse provides optimal overload protection for battery mode operation.

CPS600E

REPLACING THE BATTERY

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the

battery. Battery service should only be done by qualified professionals.

CAUTION! Use only the specified type and number of external batteries. Please see the technical

specifications for replacement batteries.

CAUTION! The battery may present a risk of electrical shock. Do not dispose of battery in a fire as

it may explode. Follow all local ordinances regarding proper disposal of batteries. Lead-acid batteries

should be recycled.

CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes

and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock.

Take the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. Do not lay tools or metal parts on top of battery or any terminals.

4. Wear rubber gloves and boots.

5. Determine if the external battery is inadvertently grounded. If grounded, remove the source of

ground. CONTACT WITH GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK!

CPS600E

DEFINITIONS FOR ILLUMINATED LCD

The LCD Display indicates a variety of EPS

operational conditions. All descriptions apply

when the EPS is plugged into an AC outlet and

turned on or when the EPS is on battery.

1. INPUT VOLTAGE Meter: This meter measures the AC voltage that the EPS is receiving from the utility

wall outlet. The EPS is designed, through the use of automatic voltage regulation, to continuously supply

connected equipment with stable, 220 output voltage. In the event of a complete power loss, severe

brownout or over-voltage the EPS will rely on its external battery to supply consistent 220 output voltage.

The Input Voltage Meter can be used as a diagnostic tool to identify poor quality input power.

2. OUTPUT VOLTAGE Meter: This meter measures, the AC voltage that the EPS is providing to the

computer. It displays normal line mode, AVR mode, and battery backup mode.

3. NORMAL MODE Icon: This icon will illuminate when the EPS is working under normal conditions.

4. ON BAT (On Battery) Icon: When a severe brownout or blackout, this icon appearing and an alarm

(two short beeps) activated indicate that the EPS is working via its batteries. Once the batteries are

running out of power, for a period of time, an alarm (two short beeps) will appear continuously. If this

occurs, it is recommended that save your files and turn off your equipment manually as soon as possible.

5. SILENT MODE Icon: This icon appearing indicates that the buzzer does not beep in the silent mode

until the low battery capacity.

6. OVER LOAD Icon: This icon appearing and an alarm activated indicate that the overload condition. To

relieve the overload, unplug your equipment from the EPS outlets until the icon disappears and the alarm

stops being activated.

7. LOAD CAPACITY: Load CAPACITY is also shown on the bar chart; equal 25% load capacity for each

segment.

8. BATTERY VOLTAGE: BATT. VOLTAGE indicates the voltage of battery.

CPS600E

EPS STATUS INQUIRY AND FUNCTIONS SETUP

GENERAL MODE

a. Press the “Display” button to check the status of the EPS

Items Unit

Input Voltage V

Output Voltage V

Load Capacity %

Battery Voltage V

b. Press and hold the Display toggle for 4 seconds.

If the machine is in the Battery Mode, it enters the silent mode. Press again for 4 seconds and it

will return to normal (buzzer) mode.

If the machine is in the Line Mode, it proceeds to Self Test.

c. If the Display toggle remains untouched for over 30 seconds, the LCD backlight will turn off

automatically.

SET-UP MODE

Step 1: Hold the Display toggle for 10 seconds to enter the EPS set-up Mode. LCD icon 1, 2 lights

indicate Set-Up Mode.

Step 2: By pressing the Display toggle, users can switch between setup functions. User configurable

functions are as follows:

a. Delay Time: The time delay between switching from Battery Mode to Line Mode. There are 9

different settings. The default setting is 0 minute.

Function description: The machine will switch from Battery Mode to Line Mode after the AC

power transmission reaches stability within the preset delay time.

b. Charging Current: The function adjusts the battery charging current according to the capacity of

the connected batteries. It can be configured for 25, 50, 75, and 100%. The default setting is

100%. 100% indicates that charging current is about 10Amps.

c. Nominal Output Voltage: Configures the correct electricity/voltage supplied in the area/country

where the EPS will be used. 220V and 230V may be selected. The system default setting is

220V.

Function description: AVR Dynamic Voltage Compensation works automatically based on the

system voltage settings.

d. Static Frequency Tolerance: There are 6 settings (1,2,4,6,8,10%), and the default setting is

+/-10%.

CPS600E

Function description: The settings may be adjusted to the quality of the electricity in use.

e. Slew Rate: Also called Dynamic Frequency Tolerance. There are 5 different settings

(0.25,0.5,1,2,4 Hz/Sec). The default value is 4Hz/sec.

Function description: “Slew Rate” indicates the tolerance of a device in accepting frequency

variances. The lower “Slew Rate” results in less tolerance but better protection for the connected

loads.

f. Low Battery Shutdown Voltage: This function adjusts the EPS shutdown point according to the

battery voltage. The default setting is 10V (with load).

g. Mode Select: The standard mode (setting: 2) and the robust mode (setting: 1) are provided to

select. Using the generators is suggested to select the robust mode (setting: 1), and using the

computers is suggested to select the standard mode (setting: 2).

The settable items are sorted by unit as in the following table：

Step 3: Press and hold the toggle for 4 seconds. When the icons blink, the value of each item can be

changed by slightly pressing the toggle.

Step 4: To save the value and return to general mode, press and hold the toggle for 4 seconds.

Note: If the machine is left idle for over 30 seconds during setup, it will turn off the backlight

and return to general mode automatically.

Note: If user wants to return to general mode without saving changes, there are two methods:

1. Wait for the backlight to turn off

2. Press and hold the “Display” toggle for 10 seconds

Items Unit Icon Lit

Delay Time Min ON BAT

Charging Current % ON BAT

Nominal Output Voltage V NORMAL MODE

Static Frequency Tolerance % NORMAL MODE

Slew Rate % None

Low Battery Shutdown Voltage V ON BAT

Mode Select None None

Inhaltsverzeichnis

Andere CyberPower UPS Handbücher

CyberPower

CyberPower CPS1250AVR Bedienungsanleitung

CyberPower

CyberPower 649532715008 Bedienungsanleitung

CyberPower

CyberPower PowerPanel Cloud Bedienungsanleitung

CyberPower

CyberPower CPS625AVR Bedienungsanleitung

CyberPower

CyberPower PR750ELCDRT1U Bedienungsanleitung

CyberPower

CyberPower CP900AVR Bedienungsanleitung

CyberPower

CyberPower CP900EPFCLCD Bedienungsanleitung

CyberPower

CyberPower 649532215003 Bedienungsanleitung

CyberPower

CyberPower OR1500LCDRTXL2U Bedienungsanleitung

CyberPower

CyberPower OP1250 Bedienungsanleitung

CyberPower

CyberPower CP1000D Bedienungsanleitung

CyberPower

CyberPower UT400EG Bedienungsanleitung

CyberPower

CyberPower UP625 Bedienungsanleitung

CyberPower

CyberPower 649532607006 Bedienungsanleitung

CyberPower

CyberPower OL6KRT Bedienungsanleitung

CyberPower

CyberPower RT650EI Bedienungsanleitung

CyberPower

CyberPower OfficePower 1500AVR-H0 Bedienungsanleitung

CyberPower

CyberPower SMP1400EILCD Bedienungsanleitung

CyberPower

CyberPower AVR CP850PFCLCD Bedienungsanleitung

CyberPower

CyberPower PFC SINEWAVE UPS Series Bedienungsanleitung

CyberPower

CyberPower BU600E-FR Handbuch

CyberPower

CyberPower OP350TE Bedienungsanleitung

CyberPower

CyberPower PP1500 Bedienungsanleitung

CyberPower

CyberPower CyberShield DTC36U12V Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung

IBM

IBM 5595-1AX Bedienungsanleitung