CyberPower STANDBY UPS Series Bedienungsanleitung

PRODUCT REGISTRATION

Thank you for purchasing a CyberPower product. This UPS is designed to provide unsurpassed

power protection, operation, and performance during the lifetime of the product. Please take a

few minutes to register your product at: www.CyberPowerSystems.com/registration.

Registration certiﬁes your product’s warranty, conﬁrms your ownership in the event of a product

loss or theft, and entitles you to free technical support. Register your product now to receive the

beneﬁts of CyberPower ownership.

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate your UPS.

CAUTION! To prevent the risk of ﬁre or

electric shock, install in a temperature and

humidity controlled indoor area free of

conductive contaminants. (Please see

speciﬁcations for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric shock,

do not remove the cover. There are no user-

serviceable parts inside.

CAUTION! Hazardous live parts inside can be

energized by the battery even when the AC

input power is disconnected.

CAUTION! The UPS must be connected to an

AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is

not grounded. If you need to de-energize this

equipment, turn o and unplug the unit.

CAUTION! To avoid electric shock, turn o the

unit and unplug it from the AC power source

before connecting equipment to the unit.

CAUTION! To reduce the risk of ﬁre, connect

only to a circuit provided with 20 amperes

maximum branch circuit over current

protection in accordance with the National

Electric Code, ANSI/NFPA 70.

CAUTION! Not for use in a computer room as

deﬁned in the Standard for the Protection of

Electronic Computer / Data Processing

Equipment, ANSI/NFPA 75.

CAUTION! Do not dispose of batteries in a ﬁre.

The batteries may explode.

CAUTION! Do not open or mutilate batteries.

Released electrolyte is harmful to the skin and

eyes. It may be toxic.

DO NOT USE FOR MEDICAL

OR LIFE SUPPORT EQUIPMENT!

CyberPower Systems does not sell products

for life support or medical applications.

DO NOT use in any circumstance that would

aect operation and safety of life support

equipment, any medical applications or

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS!

To reduce the risk of ﬁre or electric shock,

do not use with or near an aquarium.

Condensation from the aquarium can cause

the unit to short out.

DO NOT USE THE UPS

ON ANY TRANSPORTATION!

To reduce the risk of ﬁre or electric shock, do

not use the unit on any transportation such

as airplanes or ships. The eect of shock or

vibration caused during transit and the damp

environment can cause the unit to short out.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS unit

(b) User’s manual

PowerPanel® software is available on our

website. Please visit www.cyberpowersystems.

com and go to the Software Section for a free

download.

DETERMINE THE POWER

REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into

the UPS does not exceed the UPS unit’s

rated capacity. If the rated capacities of the

unit are exceeded, an overload condition

may occur and cause the UPS unit to shut

down or the circuit breaker to trip.

2. There are many factors that can aect

the amount of power that your electronic

equipment will require. For optimal system

performance keep the load below 80% of

the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately

upon receipt. However, after receiving a

new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that

you charge the battery for at least 8 hours.

Your UPS is equipped with an auto-charge

feature. When the UPS is plugged into an

AC outlet, the battery will automatically

charge whether the UPS is turned on or

turned o.

2. With the UPS unit turned o and

unplugged, connect your computer,

monitor, and any other peripherals

requiring battery backup into the battery

power supplied outlets. Plug the other

peripheral equipment (e.g. printer, scanner,

speakers, etc.) into the full-time surge

protection outlets. DO NOT plug a laser

printer, paper shredder, copier, space

heater, vacuum cleaner, sump pump,

or other large electrical device into the

“Battery and Surge Protected Outlets”.

The power demands of these devices will

overload and possibly damage the unit.

3. Plug the UPS into a 2-pole, 3-wire

grounded receptacle (wall outlet). Make

sure the wall branch outlet is protected

by a fuse or circuit breaker and does not

service equipment with large electrical

demands (e.g. air conditioner, refrigerator,

copier, etc.). The warranty prohibits the use

of extension cords, outlet strips, and surge

strips in conjunction with the UPS unit.

4. Press the power switch to turn the unit on.

The Power On indicator light will illuminate

green and the unit will “beep” twice.

5. If an overload is detected, an audible alarm

will sound and the unit will emit one long

beep. To correct this, turn the UPS o and

unplug at least one piece of equipment

from the battery power supplied outlets.

Make sure the circuit breaker is depressed

and then turn the UPS on.

6. To maintain optimal battery charge, leave

the UPS plugged into an AC outlet at all

times.

7. To store the UPS for an extended period

of time, cover it and store with the battery

fully charged. While in storage, recharge

the battery every three months to ensure

optimal battery life.

8. Ensure the wall outlet and UPS are located

near the equipment being attached for

proper accessibility.

9. Lay the UPS horizontally or use the keyhole

mounting slots to ax the UPS to the wall

in the proper orientation. DO NOT stand

the UPS up vertically.

BASIC OPERATION

1. Power On Switch

To turn the UPS on, press the power button

for approximately 2 seconds - you will hear

a constant tone (1 second) - and release

after a short beep.

To turn the UPS o, press the power button

for approximately 2 seconds - you will hear

a constant tone (1 second) - and release

after two short beeps.

Alarm setting: The audible alarm can be

turned OFF or ON by quickly pressing the

POWER button twice. The default setting

is for the Alarm On. To turn the Alarm O,

quickly press the power button twice. You

will hear two short beeps when the Alarm

is turned o. To turn the Alarm back ON,

quickly press the power button twice. You

will hear a single short beep when the

Alarm is turned on.

*When the Alarm is turned o, there will

be no audible notiﬁcation when the UPS

reaches a low battery state.

2. Power On Indicator

This LED is illuminated when the utility

power is normal and the UPS outlets are

providing power, free of surges and spikes.

3. Battery and Surge Protected Outlets

The unit has several battery powered

and surge protected outlets to ensure

temporary uninterrupted operation of your

equipment during a power failure. (DO

NOT plug a laser printer, paper shredder,

copier, space heater, vacuum cleaner, sump

pump, or other large electrical device into

the “Battery and Surge Protected Outlets.”

The power demands of these devices will

overload and possibly damage the unit.)

4. Full-Time Surge Protection Outlets

The unit has several surge suppression

outlets.

5. Circuit Breaker

Located on the side of the UPS, the circuit

breaker serves to provide overload and

fault protection.

6. USB Port to PC

The port allows connection and

communication between the USB port on

the computer and the UPS unit. The UPS

communicates its status to the PowerPanel®

Personal software.

7. Outlets Designed for AC Adapters

The UPS unit has four widely-spaced

outlets, so AC power adapters can be

plugged into the UPS without overlapping

or blocking adjacent outlets.

SYSTEM FUNCTION BLOCK DIAGRAM

Input Output

Battery Mode

Normal Mode

EMI

Filter

Surge

Suppressor

Inverter

Charger

AC / DC Battery

TROUBLESHOOTING

Problem Possible Cause Solution

Full-time surge protection outlets stop

providing power to equipment. Circuit

breaker button is projecting from the

side of the unit.

Circuit breaker has been tripped due to

an overload.

Turn the UPS o and unplug at least one

piece of equipment. Reset the circuit

breaker by depressing the button, and

then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged. Recharge the battery by leaving the UPS

plugged in.

Battery is worn out.

Contact CyberPower Systems about

replacement batteries at: cyberpower-

systems.com/support.

The UPS will not turn on.

The on/o switch is designed to prevent

damage from rapidly turning it o and

on.

Turn the UPS o. Wait 10 seconds and

then turn the UPS on.

The unit is not connected to an AC

outlet.

The unit must be connected to a 120V

60Hz outlet.

The battery is worn out.

Contact CyberPower Systems about

replacement batteries at: cyberpower-

systems.com/support.

Mechanical problem. Contact CyberPower Systems at:

cyberpowersystems.com/support.

The frequency is beyond 47 to 63 Hz

Turn the UPS o. Make sure the frequen-

cy range is within 47 to 63 Hz. Or you

can turn on with battery mode.

PowerPanel® Personal is inactive

(all icons are gray).

The USB cable is not connected.

Connect the USB cable to the UPS unit

and an open USB port on the back of

the computer.

The USB cable is connected to a bad

USB port.

Check for a dierent USB port and plug

the cable in.

The unit is not providing battery power.

Shutdown your computer and turn the

UPS o. Wait 10 seconds and turn the

UPS back on. This should reset the unit.

Additional troubleshooting information can be found at “Support” at www.CyberPowerSystems.com

DEFINITIONS FOR LED INDICATORS & AUDIBLE ALARMS

POWER ALARM

CONDITION

On O Normal

On*

Beep

twice every

30 seconds

Utility Failure - Battery Mode – The UPS is providing power to battery

power-supplied outlets from its battery.

On*

Rapid

beeping every

1/2 second

Utility Failure - Low Battery – The UPS is providing battery power. Rapid

beeping indicates the unit will run out of power soon.

O Constant tone

Overload – Occurs when connected equipment exceeds the rating of battery

outlets of the UPS. Turn the UPS o, unplug at least one piece of equipment

from battery outlets, reset the circuit breaker and turn the unit on.

On Constant tone Utility Failure – The frequency is beyond 47 to 63 Hz. The UPS will not turn

on in line mode.

* LED will ﬂash when UPS alarm is beeping.

TECHNICAL SPECIFICATIONS

Model XC625

Capacity 625 VA / 360 W

Nominal Input Voltage 120 Vac

Input Frequency 50 to 60 Hz +/- 3 Hz

On-Battery Output Voltage 120 VAC +/- 5%

On-Battery Output Frequency 50 Hz to 60 Hz +/- 1 % (auto-sensing)

Max. Load for UPS Outlets 625 VA / 360 W

Max. Load for Full-Time Surge

Protection outlets 12 Amps

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104°F / 0°C to 40°C

Operating Relative Humidity 0 to 95% non-condensing

Size (W x H x D) 9.8 in., 5.8 in., 3.2 in.

250 mm, 147 mm, 82 mm

Net Weight (lbs / kg) 6.48 lbs / 2.94 kg

Typical Battery Recharge Time 8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), cUL CSA C22.2 No. 107.3-05, FCC/DoC Class B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CyberPower UPS Handbücher

CyberPower

CyberPower CP1285AVRLCD Bedienungsanleitung

CyberPower

CyberPower CP600 Bedienungsanleitung

CyberPower

CyberPower PR750LCD Bedienungsanleitung

CyberPower

CyberPower Value 400E Bedienungsanleitung

CyberPower

CyberPower 649532004256 Bedienungsanleitung

CyberPower

CyberPower GX1500U Bedienungsanleitung

CyberPower

CyberPower OL6000ERT3U Bedienungsanleitung

CyberPower

CyberPower Value1200EILCD Bedienungsanleitung

CyberPower

CyberPower OL6000RT3UTF Bedienungsanleitung

CyberPower

CyberPower CP1500AVRL Bedienungsanleitung

CyberPower

CyberPower CPS1000EI Bedienungsanleitung

CyberPower

CyberPower Paragon OL1500RMXL2U Bedienungsanleitung

CyberPower

CyberPower Paragon OL3000RMXL2U Bedienungsanleitung

CyberPower

CyberPower CP1350EAVRLCD Bedienungsanleitung

CyberPower

CyberPower PFC SINEWAVE UPS Series Bedienungsanleitung

CyberPower

CyberPower CP825AVRLCD-G Series Bedienungsanleitung

CyberPower

CyberPower OL8KRT Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower LX1500GU Bedienungsanleitung

CyberPower

CyberPower BU600ELCD Bedienungsanleitung

CyberPower

CyberPower 649532815036 Bedienungsanleitung

CyberPower

CyberPower OfficePower 1250AVR Bedienungsanleitung

CyberPower

CyberPower UT1500EG Bedienungsanleitung

CyberPower

CyberPower 649532830022 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung

BPC

BPC 1.5K SMART Bedienungsanleitung

IBM

IBM 5595-1AX Bedienungsanleitung