Cypress Semiconductor CY25566 Bedienungsanleitung

Spread Spectrum Clock Generator

CY25566

Cypress Semiconductor Corporation • 3901 North First Street • San Jose • CA 95134 • 408-943-2600

Document #: 38-07429 Rev. *B Revised October 26, 2005

Features

• 25- to 200-MHz operating frequency range

• Wide range of spread selections (9)

• Accepts clock or crystal inputs

• Provides four clocks

—SSCLK1a

—SSCLK1b

—SSCLK2

—REFOUT

• Low-power dissipation

—3.3V = 70 mW (typical @ 40 MHz, no load)

• Center spread modulation

• Low cycle-to cycle jitter

• 16-pin SOIC package

Applications

• High-resolution VGA controllers

• LCD panels and monitors

• Printers and MFPs

Benefits

• Peak EMI reduction by 8 to 16 dB

• Fast time to market

•Cost reduction

Block Diagram Pin Configuration

116

XIN/CLKIN

REFOFF

VDD

VSS

SSCLK1a

REFOUT

SSCLK1b

SSCC

VSS

SSCLK2

XOUT

CY25566

REFERENCE

DIVIDER Loop

Filter

MODULATION

CONTROL

INPUT

DECODER

LOGIC

FEEDBACK

DIVIDER vco

DIVIDER

MUX

SSCLK1a

S0S1

12 13

20 K

20 K20 K

20 K

SSCC

VDD

VSS

Xout

Xin/

CLK

VDDVDD

VSSVSS

300K

VSS

RANGE

CONTROL

S3S2

SSCLK1b

SSCLK2

REFOUT

REFOFF

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 2 of 9

General Description

The Cypress CY25566 is a Spread Spectrum Clock Generator

(SSCG) IC used for the purpose of reducing electromagnetic

interference (EMI) found in today’s high-speed digital

electronic systems.

The CY25566 uses a Cypress-proprietary phase-locked loop

(PLL) and Spread Spectrum Clock (SSC) technology to

synthesize and frequency modulate the input frequency of the

digital clock. By frequency modulating the clock, (SSCLK1a/b

and SSCLK2), the measured EMI at the fundamental and

harmonic frequencies is greatly reduced. The modulated

output frequency is centered on the input frequency.

This reduction in radiated energy can significantly reduce the

cost of complying with regulatory agency requirements and

improve time to market without degrading system perfor-

mance.

The CY25566 provides four output clocks: SSCLK1a,

SSCLK1b, SSCLK2, and REFOUT. SSCLK1a/b and SSCLK2

are modulated clocks and REFOUT is a buffered copy of the

reference clock or oscillator. The CY25566 frequency and

spread % ranges are selected by programming S0, S1, S2,

and S3 digital inputs. S0 and S1 use three (3) logic states

including High (H), Low (L), and Middle (M) to select one of

nine available frequency and spread % ranges. Refer to

Figure 2 for details on programming three level inputs S0 and

S1. See Table 1, Table 2, and Table 3 for programming details

for S2 and S3.

The CY25566 will operate over a wide range of frequencies

from 25 to 200 MHz. Operation to 200 MHz is possible with the

use of dual drivers at pins 8 and 9. With a wide range of

selectable bandwidths, the CY25566 is a very flexible low-EMI

clock. Modulation can be disabled to provide a four-output

conventional clock.

The CY25566 is available in a 16-pin SOIC (150-mil.) package

with a commercial operating temperature range of 0°C to

70°C.

Output Clock Architecture

The CY25566 provides four separate output clocks: REFOUT,

SSCLK1a, SSCLK1b, and SSCLK2 for use in a wide variety of

applications. Each clock output is described below in detail.

REFOUT

REFOUT is a 3.3V CMOS level non-modulated inverted copy

of the clock at XIN/CLKIN. As an inverted clock, the output

clock at REFOUT is 180°out of phase with the input clock at

XIN/CLKIN. Placing a high(1) logic state of REFOFF, pin 2, will

disable the REFOUT clock. When REFOUT is disabled,

REFOUT, pin 3 is at a low(0) logic state.

Pin Description

Pin Name Type Description

1 XIN/CLKIN I Clock or Crystal connection input. Refer to Table 1,Table 2, and Table 3 for input

frequency range selection.

2REFOFFIInput pin enables REFOUT clock at pin 3. REFOFF 400KΩ internal pull-up resistor.

Logic “0” enables REFOUT, logic “1” disables REFOUT. Default = disabled.

3REFOUTOBuffered, non-modulated output clock derived from XIN/CLKIN input frequency.

There is a 180° phase shift from XIN to REFOUT.

4VDDPPositive power supply. Bypass to ground with 0.1-µF capacitor.

5, 11, 14 VSS G Positive power supply ground.

6S2IVCO range control. Refer to Table 1, Table 2, and Table 3 for detailed programming infor-

mation. Has 400-KΩinternal pull-up to VDD.

7S3IVCO range control. Refer to Table 1, Table 2, and Table 3 for detailed programming infor-

mation. Has 400-KΩinternal pull-up to VDD.

8 SSCLK1a O Modulated clock output. Pins 8 and 9 are identical but separate drivers.

9 SSCLK1b O Modulated clock output. Pins 8 and 9 are identical but separate drivers.

10 SSCC I Spread Spectrum clock control (enable/disable) function. SSCG function is enabled

when input is high and disabled when input is low. Internal 400-KΩpull-up defaults to

modulation ON.

12 S1 I Tri-level logic input control pin used to select frequency and bandwidth.

Frequency/bandwidth selection and tri-level logic programming details. See Figure 2 and

Table 1,Table 2, and Table 3. Pin 8 has internal resistor divider network to VDD and VSS.

13 S0 I Tri-level logic input control pin used to select frequency and bandwidth.

Frequency/bandwidth selection and tri-level logic programming details. See Figure 2 and

Table 1, Table 2, and Table 3. Pin 8 has internal resistor divider network to VDD and VSS.

15 SSCLK2 O Modulated output clock. Frequency of SSCLK2 = SSCLK1a/2. BW% of SSCLK2 is equal

to BW% of SSCLK1a/b.

16 XOUT O Oscillator output pin connected to crystal. Leave this pin unconnected if an external

clock drives XIN/CLK.

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 3 of 9

SSCLK1a/b

SSCLK1a and SSCLK1b are spread spectrum clock outputs

used for the purpose of reducing EMI in digital systems.

SSCLK1a and SSCLK1b can be connected in several different

ways to provide flexibility in application designs. Each clock

can drive separate nets with a capacitative load up to 15 pF

eachorconnectedtogethertoprovidedriveto a single net with

a capacitative load as high as 33 pF. When both clocks are

connected together, the CY25566 is capable of driving 3.3V

CMOS-compatible clocks to frequencies as high as 200 MHz.

If one clock output is not connected to a load, negligible EMI

willbegeneratedattheunusedpinbecausethereisno current

being driven. The frequency and bandwidth of SSCLK1a and

SSCLK1b is programmed by the logic states presented to S2

and S3. The frequency multiplication at SSCLK1a and

SSCLK1b is either 1X or 2X, controlled by S2 and S3. The

modulated output clock SSCLK1 is provided at pins 8 and 9

with each pin having separate but identical drivers. Refer to

Figure 1 below.

SSCLK2

SCLK2 is a Spread Spectrum Clock with a frequency half that

of the SSCLK1a clock frequency. When SSCLK1a is

programmed to provide a 2.5% modulated clock at 1X times

the reference clock, 40 MHz for example, the frequency of

SSCLK2 will be 20 MHz with a BW of 2.5%. Note that by

programming the frequency of SSCLK1a to 2X, the frequency

of SSCLK2 will be 1X times the reference clock frequency.

Control Logic Structures

The CY25566 has six input control pins for programming VCO

range, BW %, Mod ON/OFF and REFOUT ON/OFF. These

programmable control pins are described below.

REFOFF

The output clock REFOUT can be enabled or disabled by

controlling the state of REFOFF. When REFOFF is at a logic

low(0) state, REFOUT is enabled and the reference clock

frequency is present at pin 3. When REFOFF is at a logic high

state (1), REFOUT is disabled and is set to a logic low state

on pin 3. REFOFF has a 400-KW internal pull-up resistor to

VDD.

S0 and S1 (Tri-level Inputs)

S0 and S1 are used to program the frequency range and

bandwidth of the modulated output clocks SSCLK1a/b and

SSCLK2. S0 and S1 of the CY25566 are designed to sense

three different analog levels. With this tri-level structure, the

CY25566 is able to detect 9 different logic states. Refer to

tables 5, 6 and 7 for the results of each of these 9 states. The

level of each state is defined as follows:

Logic State “0” is a voltage that is between 0 and 0.15 × VDDV.

LogicState“M”isavoltagebetween0.4 ×VDD and0.6× VDDV.

Logic State “1” is a voltage between 0.85 × VDD and VDD.

Figure 2 illustrates how to program tri-level logic.

S2 and S3

S2 and S3 are used to program the CY25566 into different

frequency ranges and multipliers. The CY25566 operatesover

a frequency range of 25 to 200 MHz and a 1X or 2X multipli-

cation of the reference frequency. S2 and S3 are binary logic

inputs and each has a 400 K W pull-up resistor to VDD. See

Table 1, Table 2, and Table 3 for programming details.

SSCC

SSCC is an input control pin that enables or disables SSCG

modulation of the output clock at SSCLK1a/b and SSCLK2.

Disabling modulation is a method of comparing radiated EMI

in a product with SSCG turned on or off.

The CY25566 can be used as a conventional low jitter multiple

outputclockwhen SSCCissetto low(0).SSCC hasa400-KW

internal pull-up resistor. Logic high (1) = Modulation ON, logic

low (0) = Modulation OFF. Default is modulation ON.

CY25566

33 pf.

15 pf.

Figure 1. SSCLK1a/b Driver Configurations

CY25566 CY25566CY25566

10 VDD

S0 = "M" (N/C)

S1 = "0" (GND)

1313

10 10

VDD VDD

VDD

S0S0

SSCC = "1" SSCC = "1"

S1 = "0" (GND)

S0 = "1" S0 = "1"

S1 = "1"

SSCC = "1"

Figure 2.

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 4 of 9

Modulation Rate

Spread Spectrum clock generators utilize frequency

modulation (FM) to distribute energy over a specific band of

frequencies. The maximum frequency of the clock (Fmax) and

minimum frequency of the clock (Fmin) determine this band of

frequencies. The time required to transition from Fmin to Fmax

and back to Fmin is the period of the Modulation Rate, Tmod.

Modulation Rates of SSCG clocks are generally referred to in

terms of frequency or Fmod = 1/Tmod.

The input clock frequency, Fin, and the internal divider count,

Cdiv, determine the Modulation Rate. The CY25566 utilizes

two different modulation rate dividers, depending on the range

selected on S2 and S3 digital control inputs. Refer to the

example below.

TheCY25566hasthreefrequencygroupsto select from.Each

combination of frequency and bandwidth can be selected by

programming theinputcontrollines,S0–S3,tothe proper logic

state.

Group 1 is the 1X low-frequency range and operates from 25

to 100 MHz.

Group 2 is the 1X high-frequency range and operates from 50

to 200 MHz.

Group 3 is the 2X low frequency range and operates from 25

to 50 MHz and 50 to 100 MHz output.

S3, S2 CDiv Output Frequency

0,0 1166 1X

0,1 1166 2X

1,0 2332 1X

1,1 N/A N/A

Example:

Device = CY25566

Fin = 65 MHz

Range = S3 = 0, S2 = 1, S0 = 0

Then: modulation rate = Fmod = 65 MHz/1166 = 55.7 kHz

Modulation Profile Spectrum Analyzer

Figure 3. SSCG Clock, CY25566, 65 MHz

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 5 of 9

Table 1. Frequency and Bandwidth Selection Chart (Group 1)(Low Frequency (1x) Selection Chart)

25–50 MHz (Low Range)

XIN/CLK

(MHz) S1 = M

S0 = M S1 = M

S0 = 0 S1 = 1

S0 = 0 S1 = 0

S0 = M

25–35 4.3 3.8 3.4 2.9 2.8

35–40 3.9 3.5 3.1 2.5 2.4

40–45 3.7 3.3 2.8 2.4 2.3

45–50 3.4 3.1 2.6 2.2 2.1

50–100 MHz (High Range)

XIN/CLK

(MHz) S1 = 1

S0 = M S1 = 0

S0 = 1 S1 = 1

S0 = 1 S1 = M

S0 = 1

50–60 2.9 2.1 1.5 1.2

60–70 2.8 2.0 1.4 1.1

70–80 2.6 1.8 1.3 1.1

80–100 2.4 1.7 1.2 1.0

S3 S2

Table 2. Frequency and Bandwidth Selection Chart (Group 2)(High Frequency (1x) Selection Chart)

50–100 MHz (Low Range)

XIN/CLK

(MHz) S1 = M

S0 = M S1 = M

S0 =0 S1 = 1

S0 = 0 S1 = 0

S0 = M

50–60 4.2 3.8 3.2 2.8 2.7

60–70 4.0 3.6 3.1 2.6 2.5

70–80 3.8 3.4 2.9 2.5 2.4

80–100 3.5 3.1 2.7 2.2 2.1

100–200 MHz (High Range)

XIN/CLK

(MHz) S1 = 1

S0 = M S1 = 0

S0 = 1 S1 = 1

S0 = 1 S1 = M

S0 = 1

100–120 3.0 2.4 1.6 1.3

120–130 2.7 2.1 1.4 1.1

130–140 2.6 2.0 1.3 1.1

140–150 2.6 2.0 1.3 1.1

150–160 2.5 1.8 1.2 1.0

160–170 2.4 1.8 1.2 1.0

170–180 2.4 1.8 1.2 1.0

180–190 2.3 1.7 1.1 0.9

190–200 2.3 1.6 1.1 0.9

S3 S2

Table 3. Frequency and Bandwidth Selection Chart (Group 3)(Low Frequency (2x) Selection Chart)

25–50 MHz (Low Range, 2X)

XIN/CLK

(MHz) SSCLK1

(MHz) S1 = M

S0 = M S1 = M

S0 = 0 S1 = 1

S0 = 0 S1 = 0

S0 = M

25–35 50-70 4.0 3.5 3.0 2.6 2.5

35–40 70-80 3.8 3.3 2.9 2.4 2.3

40–45 80-90 3.5 3.1 2.7 2.2 2.1

45–50 90-100 3.3 2.9 2.5 2.1 2.0

S3 S2

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 6 of 9

Application Schematic

In this example, the CY25566 is being driven by a 75-MHz

reference clock.

S0 = 0 and S1 = 0 are programmed to select a BW of 2.5%.

(Refer to Table 1 and 2.)

S2 = 0 and S3 = 1 are programmed to select the Group 2

range.

VDD = 3.30 VDC.

SSCLK1a = 75 MHz @ 2.5% center spread modulation.

SSCLK1b = 75 MHz @ 2.5% center spread modulation.

SSCLK 2 = 37.5 MHz @ 2.5% center spread modulation.

REFOUT = 37.5 MHz non-modulated clock.

CY25566

XIN/CLKIN

XOUT

REFOFF

SSCC

REFOUT

SSCLK2

SSCLK1a

SSCLK1b

VDD

VSS VSS VSS

VDD

75 MHz Clock source

REFOUT

SSCLK2

SSCLK1a

SSCLK1b

0.1 uF

51114

Figure 4. Application Schematic

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 7 of 9

Absolute Maximum Ratings[1, 2]

Supply Voltage (VDD: .......................................................+6V

Operating Temperature:......................................0°C to 70°C

Storage Temperature ..................................–65°Cto+150°C

Table 4. DC Electrical Characteristics VDD = 3.3V, Temp. = 25°C, unless otherwise noted

Parameter Description Conditions Min. Typ. Max. Unit

VDD Power Supply Range ±10% 2.97 3.3 3.63 V

VINH Input High Voltage S0 and S1 only. 0.85VDD VDD VDD V

VINM Input Middle Voltage S0 and S1 only. 0.40VDD 0.50VDD 0.60VDD V

VINL Input Low Voltage S0 and S1 only. 0.0 0.0 0.15VDD V

VOH1 Output High Voltage IOH = 6 ma, SSCLKa 2.4 V

VOH2 Output High Voltage IOH = 20 ma, SSCLKb 2.0 V

VOL1 Output Low Voltage IOH = 6 ma, SSCLKa 0.4 V

VOL2 Output Low Voltage IOH = 20 ma, SSCLKb 1.2 V

Cin1 Input Capacitance Xin/CLK (Pin 1) 3 4 5 pF

Cin2 Input Capacitance Xout (Pin 8) 6 8 10 pF

Cin2 Input Capacitance All input pins except 1. 3 4 5 pF

IDD1 Power Supply Current FIN = 40 MHz,15 pF@all outputs 27 32 mA

IDD1 Power Supply Current FIN = 40 MHz, No Load 21 28 mA

IDD2 Power Supply Current FIN = 165 MHz,15 pF@all outputs 68 80 mA

IDD2 Power Supply Current FIN = 165 MHz, No Load 48 60 mA

Table 5. Electrical TimingCharacteristics VDD =3.3V, T=25°C andCL=15pF,unlessotherwisenoted.Rise/Fall@ 0.4–2.4V,

[email protected]

Parameter Description Conditions Min. Typ. Max Unit

ICLKFR Input Clock Frequency Range Non-crystal, 3.0V Pk–Pk ext. source 25 200 MHz

tRISE(a) Clock Rise Time SSCLK1a or SSCLK1b, Freq = 100 MHz 1.0 1.3 1.6 ns

tFALL(a) Clock Fall Time SSCLK1a or SSCLK1b, Freq = 100 MHz 1.0 1.3 1.6 ns

tRISE(a+b) Clock Rise Time SSCLK1(a+b), CL = 33 pF, 100 MHz 1.2 1.5 1.8 ns

tFALL(a+b) Clock Fall Time SSCLK1(a+b), CL = 33 pF, 100 MHz 1.2 1.5 1.8 ns

tRISE(a+b) Clock Rise Time SSCLK1(a+b), CL = 33 pF, 200 MHz 1.1 1.4 1.7 ns

tFALL(a+b) Clock Fall Time SSCLK1(a+b), CL = 33 pF, 200 MHz 1.1 1.4 1.7 ns

tRISE(REF) Clock Rise Time REFOUT, Pin 3, CL = 15 pF, 50 MHz 1.0 1.3 1.6 ns

tFALL(REF) Clock Fall Time REFOUT, Pin 3, CL = 15 pF, 50 MHz 1.0 1.3 1.6 ns

DTYin Input Clock Duty Cycle XIN/CLK (Pin) 30 50 70 %

DTYout Output Clock Duty Cycle SSCLK1a/b (Pin 8 and 9) 45 50 55 %

CCJ1 Cycle-to-Cycle Jitter F = 100 MHz, SSCLK1a/b CL = 33 pF 300 400 ps

CCJ2 Cycle-to-Cycle Jitter F = 200 MHz, SSCLK1a/b CL = 33 pF 500 600 ps

REFOUT Refout Frequency Range CL = 15 pF 25 108 MHz

Note:

1. Operation at any Absolute Maximum Rating is not implied.

2. Single Power Supply: The voltage on any input or I/O pin cannot exceed the power pin during power-up.

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 8 of 9

of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize

its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress

Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.

Package Drawing and Dimensions

All product and company names mentioned in this document are the trademarks of their respective holders.

Ordering Information

Part Number Package Type Product Flow

CY25566SC 16-pin SOIC Commercial, 0°to 70°C

CY25566SCT 16-pin SOIC–Tape and Reel Commercial, 0°to 70°C

PIN 1 ID

0°~8°

16 Lead (150 Mil) SOIC

916

SEATING PLANE

0.230[5.842]

0.244[6.197]

0.157[3.987]

0.150[3.810]

0.386[9.804]

0.393[9.982]

0.050[1.270]

BSC

0.061[1.549]

0.068[1.727]

0.004[0.102]

0.0098[0.249]

0.0138[0.350]

0.0192[0.487]

0.016[0.406]

0.035[0.889]

0.0075[0.190]

0.0098[0.249]

DIMENSIONS IN INCHES[MM] MIN.

MAX.

0.016[0.406]

0.010[0.254] X 45°

0.004[0.102]

REFERENCE JEDEC MS-012

PART #

S16.15 STANDARD PKG.

SZ16.15 LEAD FREE PKG.

PACKAGE WEIGHT 0.15gms

16-Lead (150-Mil) SOIC S16.15

51-85068-*B

[+] Feedback

CY25566

Document #: 38-07429 Rev. *B Page 9 of 9

Document Title:CY25566 Spread Spectrum Clock Generator

Document Number: 38-07429

Rev. ECN No. Issue

Date Orig. of

Change Description of Change

** 115771 07/01/02 OXC New Data Sheet

*A 122705 12/30/02 RBI Added power up requirements to maximum ratings information.

*B 404070 See ECN RGL Minor Change: Typo error on table 1, column 2 , S0 = 0 (not M)

[+] Feedback

Inhaltsverzeichnis

Andere Cypress Semiconductor Computerhardware Handbücher

Cypress Semiconductor

Cypress Semiconductor Perform CY62146E MoBL Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1019D Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1511JV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C64013C Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY8C24123A Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor NoBL CY7C1470BV25 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C2563KV18 Kurzanleitung

Cypress Semiconductor

Cypress Semiconductor NoBL CY7C1460AV25 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor Perform CY7C1380D Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1297H Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1310BV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor PSoC CapSense CY8CKIT-031 Handbuch

Cypress Semiconductor

Cypress Semiconductor CY7C1310AV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1344H Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY62146EV30 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1422BV18 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor FLEx36 CYD01S36V Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1019CV33 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C027AV Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY7C1333H Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CYV15G0100EQ Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor Perform CY7C132 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor Perform STK14D88 Bedienungsanleitung

Cypress Semiconductor

Cypress Semiconductor CY8C21234 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung