Cytron Technologies Shield-PS2 Bedienungsanleitung

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

Shield-PS2

Cytron PS2 Shield

User's Manual

V1.0

September 2013

 
ROBOT . HEAD to TOE 
                                                                    Product User’s Manual – Shield-PS2 
 
Index 
 
1. Introduction and Overview 3 
 
2. Packing List 4 
 
3. Product Specification and Limitations 5 
 
4. Board and Product Layout 6  
 
5. Hardware Interface 8 
      5.1   Choose PS2 Dual Shock Controller 10 
 
6. Protocol 15 
      6.1  PS2 Button and joystick status 15 
      6.2   On Board vibrator motor control 16 
      6.3   All PS2 button and joystick status 17 
 
7. Warranty 19 
 
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved  2

 
ROBOT . HEAD to TOE 
                                                                    Product User’s Manual – Shield-PS2 
 
 
 1.0 INTRODUCTION AND OVERVIEW 
 
Cytron PS2 Shield (SHIELD-PS2) is an Arduino compatible shield which is compatible with                         
Arduino UNO,Arduino Duemilanove,Arduino Mega, Arduino Leonardo and possibly other              
pin compatible main boards. Cytron PS2 Shield offers a compact yet reliable PS2 Controller                           
Converter for user. Cytron PS2 Shield is powered from Arduino main board. with Cytron PS2                             
Shield Reading Joy-stick and button’s state of PS2 controller will be as easy as reading                             
UART data. It offers a standard connector for SONY PS2 controller to plug-in, either wired                             
or wireless. 
 
Shield-PS2 has stackable side headers which allows for more Arduino shields to be stacked                           
on top of it. Besides, user has option to use either hardware or software UART with                               
Arduino’s main board to communication to get the PS2 controller status. Shield-PS2 reset is                           
connected to arduino’s analog pin 1 (A1). User can pull down this analog pin to reset the                                 
shield.  
 
Features: 
●5V powered, low current consumption. 
●Simple to use UART protocol 
●Vibrator motor on PS2 is controllable. 
●Wired and Wireless PS2 controller is supported. 
●PS2 Controller will automatically operate in analog mode. 
●A status LED  
●Jumper selector to select different UART Baud Rate (4800, 9600, 57600, 115200).  
●Jumper selectors to select different digital pin as UART TX and RX pin.  
 
  
 
Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved  3 
 

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

2.0 PACKING LIST

1. 1 x Shield-PS2

2. 3 x mini jumper

3. User’s manual, and sample source code can be downloaded from

http://www.cytron.com.my.

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

3.0 PRODUCT SPECIFICATION AND LIMITATIONS

Dimensions

Parameters

Min

Typical

Max

Unit

Input Voltage (Logic Operation Voltage)

4.5

5.5

Current Consumption

100

150

500

VIOH (Logic Input – High Level)

3.5

5.0

5.5

VIOL (Logic Input – Low Level)

1.0

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

4.0 PRODUCT LAYOUT

Components on Shield-PS2 and their functions:

1. Stackable Analog Input Header

This is the analog port of the Arduino. The stackable header allows other stacked

shield to utilize these pins.

2. Stackable Power Pins Header

This is the power port of the Arduino. The stackable header allows other stacked

shield to utilize these pins.

3. Main Board reset button

Arduino main board will require around 30ms to ready after reset.

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

4. Status indicator LED (Orange)

This LED will blink and illuminate with different brightness depending on the PS2

status.

LED Condition

Description

Blink with

different brightness

Once power up, if there is no SONY PS2 controller connected or

detected..

Stay illuminated

with low brightness

SONY PS2 controller detected and communication is working fine.

Stay illuminated

with high

brightness

Digital button on SONY PS2 controller is pressed.

5. Power indicator LED (Green)

Indicator to shows that power is supplied to Cytron PS2 Shield.

6. Baud Rate selector

To select the preferable UART baud rate For Cytron PS2 Shield to obtain latest

baudrate from selector, Shield-PS2 need to be reset to update the board’s baud rate.

7. On board Cytron PS2 Shield reset button

PS2 RST button will only reset the SHIELD-PS2 but not the Arduino Main board.

8. Stackable Digital I/O Headers

JP4 and JP7 are Digital I/O pins stacked to the Arduino main board.

9. RX Pin Selector

User may select D0, D2, D8 or D10 as the RX pin from Arduino main board with the

mini jumper. If Arduino UNO or Mega is used, recommended to move the RX pin

selector to D2, D8 or D10 as D0 is used for bootloader (loading program).

10. TX Pin Selector

User may select D1, D3, D9 or D11 as the TX pin from Arduino main board with the

mini jumper. If Arduino UNO or Mega is used, recommended to move the TX pin

selector to D3, D9 or D11 as D1 is used for bootloader (loading program).

11. SONY PS2 Connector Socket

Please connect PS2 Controller plug here, wireless or wired.

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

5.0 HARDWARE INTERFACE

This section shows the example of using SHIELD-PS2 with Arduino UNO as the main

controller. However, other Arduino main board such as Arduino Duemilanove and Arduino

Mega can also be used.

Figure below shows that the SHIELD-PS2 is stacked on the Arduino UNO. Please ensure that

the pins alignment is correct.

Select the pins for UART’s TX and RX. Pin D0 and D1 are hardware serial of most arduino

main board. Other selectable pin for TX and RX on Shield-PS2 are software serial pin. The

default TX pin is set to D3 while the RX pin is set to D2. However, other pins may be

selected if these pins are already used by other application. If hardware serial pin (D0, D1) is

selected, user needs to unplug the PS2 Connector from the Shield-PS2 before start to

program the main board. Programming of main board may fail if the Shield-PS2 is stacked on

mainboard and PS2 controller connector is connected. Select desired baudrate for Shield-PS2

using the mini jumper.

Guideline to choose pin for software serial:

Not all pins on the Mega and Mega 2560 support change interrupts,

so only the following can be used for RX:

10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69

Not all pins on the Leonardo support change interrupts,

so only the following can be used for RX:

8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

USB cable to Arduino main board and load example code. Sample source code and

Arduino’s Library can be downloaded from the SHIELD-PS2 product page at Cytron’s

website.

Connect the PS2 joystick to the PS2 connector socket on SHIELD-PS2 as shown. Don’t

forget about the power source for the Arduino main board too. Power source for the Arduino

main board is from DC adaptor plug.

ROBOT . HEAD to TOE

Product User’s Manual – Shield-PS2

Andere Handbücher für Shield-PS2

Inhaltsverzeichnis

Andere Cytron Technologies Trägerplatine Handbücher

Cytron Technologies

Cytron Technologies Shield-PS2 Bedienungsanleitung

Beliebte Trägerplatine Handbücher anderer Marken

CTJ

CTJ TX2 Bedienungsanleitung

Amfeltec

Amfeltec AngelShark Series Bedienungsanleitung

Advantech

Advantech CPC-2420 Installations- und Betriebshandbuch

Bob's Space Racers

Bob's Space Racers BSR-3000 Bedienungsanleitung

RTimes

RTimes Z509 Bedienungsanleitung

mikroElektronika

mikroElektronika Clicker 2 Bedienungsanleitung

Connect Tech

Connect Tech Sprocket Carrier Bedienungsanleitung

ETAS

ETAS ES5372.1-B Bedienungsanleitung

TQ-Systems

TQ-Systems MBa7x Bedienungsanleitung

Arbor Technology

Arbor Technology PBE-1101 Bedienungsanleitung

Aetina

Aetina AN310 Bedienungsanleitung

RTimes

RTimes Z603L/LE Bedienungsanleitung

Hemisphere GPS

Hemisphere GPS SBX-4 Montageanleitung

REDEKOP

REDEKOP Actuated Tailboard Bedienungsanleitung

XJTAG

XJTAG SPEA 3030 Bedienungsanleitung

Exor

Exor GigaSOM gS01 Bedienungsanleitung

Aaeon

Aaeon ECB-920A-A11 Bedienungsanleitung

ESD

ESD PCIe-XPIMC-Carrier Bedienungsanleitung