D-CUT TC-330 Bedienungsanleitung
OPERATION MANUAL
D-CUT Flooring / Trim Cutter TC-330
www.dcutproducts.com
2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Keep the cutting
head in a close position with lock pins when the cutter is not in use.
3
CUTTING AND C
Installation of t
he
C
utter
(1)
Install the handle assembly to
the cutter base as shown.
Warning: Do not put your
fingers against the sharp edge
of the blade
at
any time.
Angle
Cut
Position the guide bar at 45°.
Insert a baseboard or a shoe
mold between the cutting
blade and the base, flush with
the guide bar as shown, then
pull the handle down to
complete a cut.
Straight
Cut
Insert the floor plank between
the cutting blade and the base,
flush with the guide bar on the
working table, hold the plank
and pull handle down to
complete a cut.
4
Bevel
Cut
(1)
Make a straight cut on a
workpiece to your
measurement and then pull
the knob as pointed by an
arrow, adjust the cutter head
to your desired angle. Pull
out the handle from the base
to change the handle
position on the cutting head.
Bevel
Cut
(2)
Insert the workpiece between
the cutting blade and flush the
working table with the guide
bar, and stop the edge of the
workpiece from previous
straight cut at the cutting base
where you can see and feel it
while you're moving along the
workpiece, hold the workpiece
firmly, and then pull the handle
down to complete a cut.
Changing t
he
Blade
Use provided Allen wrench
to Loosen the five screws as
shown, the blade by each
end and carefully move the
blade out of blade holder.
Note: the flat side of the
blade should face the
working table.
Warning: Do not put your
fingers against the sharp
edge of the blade at any
time.
5
Lock
t
he
Cutt
ing
Head
Use the provided Lock Pin to
tuck the hole on the main
column as shown. Make sure
the cutting blade is in a close
position when the cutter is not
in use.
Transport
Once the lock pins firmly
locked the cutting head and
pull out the handle to carry the
cutter as shown.
Changing t
he
Nylon
Bar
Use provided Allen wrench to
Loosen the five screws, then
carefully move nylon bar out of
the nylon bar holder.
Note: the flat side of the blade
should face the working table.
Warning: Do not put your
fingers against the sharp edge of
the blade at any time.
6
Explosive View
7
Explosive View
8
Parts Q’ty
Parts Q’ty
1
Wheel 2 34
Screw M6X20 4
2
Screw 1 35
Handle Base 4
3
Sleeve 2 36
Bolt M12X95 2
4
Washer 10 2 37
Screw M8 B 1
5
Screw M8 X14 2 38
Screw M8 C 1
6
Screw M5 X 12 17 39
Handle A 1
7
Rectangular Tube 1 40
Handle Base 1
8
Nylon Bar 1 41
Nut M4 2
9
Nylon Bar Holder 1 42
left ABS handle 1
10
Washer 5 6 43
Right ABS handle 1
11
Guide Sleeve 2 44
Screw M4X30 2
12
Spring Washer 8 2 45
Screw M4X20 1
13
Screw M8X16 2 46
Rubber Feet 2
14
Locker Nut M5 3 47
Washer 5 4
15
Slide Pathway 1 48
Cutter Base 1
16
Bolt M8X16 4 49
Lock Pin 1
17
Nut M5 1 50
Screw M4X10 2
18
Left Rotation Plate 1 51
Lock Pin Base 1
19
Spring 2 52
Shaft 4
20
Screw M5X16 13 53
Locker Nut M12X1.5 2
21
God 2 54
Washer 12 2
22
Working Table 1 55
Right Rotation Plate 1
23
Guide Bar 1 56
Locker Nut M10 2
24
M8 Screw A 1 57
Knurled Angle Knob 2
25
Screw M6X12 5 58
Tension Spring 2
26
Blade 1 59
Left Angle Position Shaft 1
27
Locker Nut M12 2 60
Screw M8 X16 2
28
Blade Holder 1 61
Bearing 1
29
Nylon Cam Ring 4 62
Locker Nut M8 2
30
Eccentric Cam Bracket 2 63
Slider 1
31
Shaft 2 64
Locker Nut M6 1
32
Special Screw 2 65
Screw M6 X10 2
33
Aluminum Eccentric Cam 1 66
Left Angle Position Shaft 1
Explosive View
Andere D-CUT Cutter Handbücher
D-CUT
D-CUT MD-630 Bedienungsanleitung
D-CUT
D-CUT LT-200 Bedienungsanleitung
D-CUT
D-CUT SC-230 Bedienungsanleitung
D-CUT
D-CUT LT-180 Bedienungsanleitung
D-CUT
D-CUT AK-360 Bedienungsanleitung
D-CUT
D-CUT MH-510 Bedienungsanleitung
D-CUT
D-CUT MD-230 Bedienungsanleitung
D-CUT
D-CUT LU-215 Bedienungsanleitung
D-CUT
D-CUT HC-040 Bedienungsanleitung
D-CUT
D-CUT PL-215 Bedienungsanleitung
D-CUT
D-CUT GC-230 Bedienungsanleitung
D-CUT
D-CUT MH-330 Bedienungsanleitung
D-CUT
D-CUT SC-620 Bedienungsanleitung
D-CUT
D-CUT LX-340 Bedienungsanleitung
D-CUT
D-CUT LX-230 Bedienungsanleitung
D-CUT
D-CUT TC-100 Bedienungsanleitung
D-CUT
D-CUT MD-460 Bedienungsanleitung
D-CUT
D-CUT TC-230 Bedienungsanleitung
D-CUT
D-CUT LH-320 Bedienungsanleitung
D-CUT
D-CUT DP-340 Bedienungsanleitung
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
