D-Link DWC-2000 Bedienungsanleitung
Quick Installation Guide
Краткое руководство по установке
4 x 100/1000Base-T/SFP combo ports to
2 USB ports Wireless Controller
Бе проводной контроллер 4 комбо-портами
100/1000Base-T/SFP и 2 USB-портами
DW -2000
Introduction
This guide gives step-by-step instructions for setting up your D-Link DWC-2000 Wireless Controller. Please
note that the model you have purchased may appear slightly different from those shown in the illustrations.
The DWC-2000 Wireless Controller is a full-featured wireless LAN controller designed for medium to large
network environments. The controller has a range of network and access point management functions, can
control up to 64 access points by default, and up to 256 with license pack upgrades.
The DWC-2000 can be upgraded with three optional license packs:
• The DWC-2000-AP32/DWC-2000-AP32-LIC License Packs allow management of up to 32 additional
access points.
• The DWC-2000-AP64/DWC-2000-AP64-LIC License Packs allow management of up to 64 additional
access points.
• The DWC-2000-AP128/DWC-2000-AP128-LIC License Packs allow management of up to 128 additional
access points.
The DWC-2000 can be upgraded multiple times with license packs, enabling support for up to a maximum of
256 access points.
Package ontents
• DWC-2000 Wireless Controller
• Power Cord
• Console Cable (RJ-45 to DB-9 Cable)
• Ethernet Cable (CAT5 UTP/Straight Through)
• Reference CD
• Rack Mounting Brackets (2)
• Screws Pack
• QIG
Product Overview
Item Part Description
A Reset button System reset
B Power LED Indicates if the wireless controller is powered on
C Fan LED Indicates the fan status on the wireless controller
D USB ports (1-2) These ports can support various USB 1.1 or 2.0 devices
E Hard disk drive module slot Slot for the hard disk drive module
F Gigabit LAN SFP ports (1-4) Connect to Ethernet devices such as computers,
switches, and hubs
G Gigabit LAN RJ-45 ports (1-4) Connect to Ethernet devices such as computers,
switches, and hubs
H Console port Used to access the Command Line Interface (CLI) via an
RJ-45 to DB-9 console cable
I Power switch Powers On/Off the device
J Power outlet Connects to the power cord
Status LEDs and Ethernet Port LEDs
The following table lists the name, color, status, and description of each device LED.
LED
Indicator
olour Status Description
Power/
Status
Orange/
Green
Solid Orange Power-on process in progress
Solid Green Power-on process complete
Blinking Orange Device has crashed and is in recovery mode
Light Off The device is powered off
Fan Green/
Red
Solid Green The fan is operating normally
Solid Red The fan has failed
USB Green Solid Green The link is good
Blinking Green There is activity on this port
Light Off No link
Tx/Rx
Status of
RJ-45 Port
Green Solid Green Link is present
Blinking Green Port is sending or receiving data
Light Off No link
Link Speed of
RJ-45 Port
Green/
Orange
Solid Green Port is operating at 100 Mbps
Solid Orange Port is operating at 1000 Mbps
Light Off Port is operating at 10 Mbps
Link and
TX/RX of
SFP Port
Green/
Orange
Solid Green Port is operating at 100 Mbps
Blinking Green Port is sending or receiving data at 100 Mbps
Solid Orange Port is operating at 1000 Mbps
Blinking Orange Port is sending or receiving data at 1000 Mbps
Default Interface Settings
Ethernet Interface Interface Type IP Address Web-Based
Management
LAN (1-4) Static IP 192.168.10.1/24 Enabled
Installation and onnection
Before You Begin
Observe the following precautions to help prevent shutdowns, equipment failures, and injuries:
• Before installation, always check that the power supply is disconnected.
• Ensure that the room in which you are operating the device has adequate air circulation and that the room
temperature does not exceed 40 °C (104 °F).
• Ensure there is at least one meter (three feet) of clear space in front and back of the device.
• Do not place the device in an equipment rack frame that blocks the air vents on the sides of the chassis.
Ensure that enclosed racks have fans and louvred sides.
• Ensure that none of these hazardous conditions exist before installation: moist or wet floors, leaks,
ungrounded or frayed power cables, or missing safety grounds.
Installation
You can mount the DWC-2000 into a standard 19-inch equipment rack. To install the DWC-2000 into a rack:
1. Attach the mounting brackets to each side of the chassis as shown in Figure 5 and secure them with the
screws provided.
2. Use the screws provided with the equipment rack to mount the device in the rack as shown in Figure 6.
onnecting the Device to a Network
Connect the necessary cables as shown in Figure 7.
1. Connect an RJ-45 cable from one of the ports labelled LAN (1-4) to a switch in the LAN network segment.
2. Connect an RJ-45 to DB-9 cable from the console port to a workstation to use the CLI (Command Line
Interface) for management.
Powering on the Device
To connect the device to a power source, plug one end of the AC power cord into the AC power connector on
the back panel of the device. Plug the other end into an electrical outlet and switch ON the power switch.
Note: We recommend using a surge protector for the power connection.
Initial onfiguration
The wireless controller software is preinstalled on the DWC-2000. When the device is powered on, it is ready
to be configured. It comes with a default factory configuration that allows you to connect to it, but you should
configure the controller for your specific network requirements.
Discovering the Wireless ontroller
Using the Web UI
To use the Web UI, the workstation from which you are managing the device must initially be on the same
subnet as the device. You will also need a compatible browser:
Browser Minimum Version
Microsoft
Internet Explorer
9, 10
Mozilla Firefox 23
Apple Safari iOS: 6.1.3
Windows: 5.1.7
Google Chrome 26
To access the device’s Web UI:
1. Connect your workstation to one of the ports labelled LAN (1-4).
2. Ensure your workstation is configured with a static IP address in the 192.168.10.0/24 subnet.
3. Launch your browser and enter the IP address for the LAN interface
(The default IP address is http://192.168.10.1), then press Enter.
4. Log into the wireless controller Web interface. The default login information is:
• Username: admin
• Password: admin
onnecting via onsole (RJ-45 to DB-9 D E)
The DWC-2000 Wireless Controller provides a serial port that allows you to connect to a computer or
terminal for monitoring and configuring the device. This port is an RJ-45 connector, and is implemented as a
data communication terminal equipment (DCE) connection.
To use the console port connection, you need the following equipment:
1. A terminal or a computer with both a serial port and the ability to emulate a terminal.
2. The included RJ-45 to DB-9 cable.
3. If your laptop or PC does not run RS-232 interface, USB-to-RS232 connector (not included) is required.
To establish a console connection:
1. Plug the RJ-45 connector end of the supplied RJ-45 to DB-9 cable directly into the console port on the
wireless controller.
2. Connect the other end of the cable to a terminal or to the serial connector of a computer running terminal
emulation software (f.i. Hyperterminal, Putty, Mimicom etc). Set the terminal emulation software values as
follows:
• Baud rate: 115200
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
3. Connect the wireless controller following the instructions in the “Powering on the Device” section in this
guide. The boot sequence will be displayed on the terminal.
4. Once the boot sequence is completed, the command prompt will be displayed and the device is ready to
be configured.
Discovering and Managing the Unified AP
To discover and manage the Unified AP:
1. Record the MAC address of each Unified AP on the network.
2. Connect the Unified AP you want to configure to the local area Ethernet network.
3. Log into the DWC-2000 and set the LAN IP address to be in the subnet of the local area Ethernet network.
4. Go through the Wizard to manage your access points.
4.1 Click “Wizard” at the top right corner.
4.2 Click the “Run...” button to run the WLAN Wizard.
4.3 Wireless Global Configuration: Choose the country code.
4.4 Wireless Default Radio Configuration: Create an AP Profile for the radio setting of the wireless network.
Set the radio mode for each radio.
4.5 Wireless Default VAP Configuration: Enter the SSID network name, and then select a security method. If
you select Static WEP or WPA Personal, enter a secure passphrase for your WLAN.
4.6 Below are two methods to add access points in the managed AP list:
a. List of APs Awaiting to be Configured:
Select the access points which are discovered automatically by the wireless controller.
b. Valid Access Point Summary: Enter access point MAC address manually.
List of APs Awaiting to be Configured: This is a list of discovered access points. Switch the Status of the
access point you want to manage to ON.
Valid Access Point Summary: Enter the MAC address of the AP you want to manage.
4.7 When the WLAN Connection Setup Wizard has been completed, click the Connect button to save your
settings and connect your Aps.
Additional Information
You can refer to the additional documentation on the accompanying master CD or you can visit
http://www.dlink.com for more support on how to configure your DWC-2000.
Правила и условия безопасной эксплуатации
Внимательно прочитайте данный раздел перед у тановкой и подключением у трой тва. Убедите ь,
что у трой тво не имеет механиче ких повреждений. У трой тво должно быть и пользовано только по
назначению, в оответ твии кратким руковод твом по у тановке.
У трой тво предназначено для эк плуатации в ухом, чи том, незапыленном и хорошо
проветриваемом помещении нормальной влажно тью, в тороне от мощных и точников тепла. Не
и пользуйте его на улице и в ме тах повышенной влажно тью. Не размещайте на у трой тве
по торонние предметы. Вентиляционные отвер тия у трой тва должны быть открыты. Температура
окружающей реды в непо ред твенной близо ти от у трой тва и внутри его корпу а должна быть в
пределах от 0 до +40 °C.
Электропитание должно оответ твовать параметрам, указанным в техниче ких характери тиках
у трой тва.
Не в крывайте корпу у трой тва! Перед началом у тановки или перед очи ткой у трой тва от
загрязнений и пыли отключите питание у трой тва. Удаляйте пыль помощью влажной алфетки. Не
и пользуйте жидкие/аэрозольные очи тители или магнитные/ татиче кие у трой тва для очи тки.
Избегайте попадания влаги в у трой тво и адаптер питания.
Срок лужбы у трой тва - 2 года.
Гарантийный период и чи ляет я момента приобретения у трой тва у официального дилера на
территории Ро ии и тран СНГ и о тавляет один год.
Вне зави имо ти от даты продажи гарантийный рок не может превышать 2 года даты производ тва
изделия, которая определяет я по 6 (год) и 7 (ме яц) цифрам ерийного номера, указанного на
наклейке техниче кими данными.
Год: 9 - 2009, A - 2010, B - 2011, C - 2012, D - 2013, E – 2014, F - 2015, G - 2016, H - 2017, I - 2018.
Ме яц: 1 - январь, 2 - февраль, ..., 9 - ентябрь, A – октябрь, B - ноябрь, C - декабрь.
Введение
В этом кратком руковод тве по у тановке даны ин трукции по на тройке бе проводного контроллера
DWC-2000. Приобретенная модель может незначительно отличать я от показанной на иллю трациях.
Контроллер DWC-2000 являет я полнофункциональным решением для централизованного
управления у трой твами в бе проводной ети LAN для малого и реднего бизне а. У трой тво
позволяет управлять до 64 бе проводными точками до тупа (ТД) по умолчанию и до 256 ТД при
наличии ра ширенного лцензионного пакета.
Для обновления контроллера DWC-2000 уще твует три типа дополнительных лицензий:
• DWC-2000-AP32/DWC-2000-AP32-LIC позволяет дополнительно управлять 32 ТД.
• DWC-2000-AP64/DWC-2000-AP64-LIC позволяет дополнительно управлять 64 ТД.
• DWC-2000-AP128/DWC-2000-AP128-LIC позволяет дополнительно управлять 128 ТД.
Для контроллера DWC-2000 преду мотрено неоднократное обновление лицензии, что позволяет
увеличить мак имальное количе тво ТД, до тупных для управления, до 256.
Комплект поставки
• Бе проводной контроллер D-Link DWC-2000
• Кабель питания
• Кон ольный кабель (RJ-45 to DB-9)
• Ethernet-кабель (UTP категории 5/кабель прямого подключения)
• CD-ди к
• Крепежный кронштейн – 2 шт
• Крепежные винты
• Краткое руковод тво по у тановке
Е ли что-либо от ут твует, обратите ь к Вашему по тавщику.
Andere Handbücher für DWC-2000
4
Inhaltsverzeichnis
Sprachen:
Andere D-Link Controller Handbücher
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link Nuclias Connect Hub Plus DNH-200 Bedienungsanleitung
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link DWC-2000 Bedienungsanleitung
D-Link
D-Link DHP-P339AV Bedienungsanleitung
D-Link
D-Link DWC-1000 Bedienungsanleitung
D-Link
D-Link PowerLine DHP-W611AV Bedienungsanleitung
