D-Link DFL-1000 Bedienungsanleitung

Important Information

Before you begin installing your new DFL-1000 you must have:

1.1 Internal IP Address: _____._____._____._____

1.2 Internal Netmask: _____._____._____._____

1.3 External IP Address: _____._____._____._____

1.4 External Netmask: _____._____._____._____

1.5 Default Gateway Address: _____._____._____._____

1.6 DMZ IP Address: _____._____._____._____

1.7 DMZ IP Netmask: _____._____._____._____

• Default Gateway Address, External IP and Netmask will be supplied by your

Internet Service Provider.

• DMZ Address and Netmask are only needed if DMZ will be used.

Checking The Package Contents

Includes Power Cord, 1 Crossover Ethernet Cable (blue), 1 Straight Ether-

net Cable (grey),1 Null-Modem Serial Cable, User Manual and

QuickStart Guide.

Powering up the DFL-1000

Connect the power cord to the DFL-1000 and plug it in. The Power

indicator on the front panel will light up and then the Status light will begin

flashing, indicating that startup has begun. After about 45 to 60 seconds

the DFL-1000 will be ready for use.

Configuring the DFL-1000

There are two ways to configure the network interface addresses of the

DFL-1000.

1. Using Microsoft Internet Explorer © web interface:

• Set the IP address of your management computer to 192.168.1.2 with netmask

255.255.255.0

• Connect the management computer to the Internal interface of the DFL-1000

through an crossover ethernet cable or network hub

• In the Internet Explorer Address Bar enter https://192.168.1.99

• Enter "admin" for the user name, leave the password blank and click OK

• Click on System and then on Network. Addresses can be viewed and set on

the IP Address page.

• Once the addresses are set you are ready to connect the DFL-1000 to your

network. Section 6 below will guide you through this process.

2. Using command line interface:

• Connect one end of the null-modem serial cable to the Console connector at

the front of the DFL-1000 and connect the other end to the serial port of an

administration computer or terminal.

• Start a terminal program, for example the HyperTerminal included with the Win-

dows operating system.

• For the terminal port parameters set Bits per Second to 115200, Data bits to 8,

Parity to None and Stop bits to 1.

• At the Login prompt type admin, no password required.

• Follow the instructions in the next section to set the interface addresses.

Setting the IP Addresses

First set the internal interface address to be in your internal network.

For example:

• set interface internal address 192.168.100.165

Next set the mask for your internal subnet:

• set interface internal netmask 255.255.255.0

Now set up the external interface:

• set interface external address 172.16.0.85

• set interface external netmask 255.255.255.224

Set the default gateway to the gateway address provided by your ISP:

• set defaultgw 172.16.0.94

At this point you should check the current settings.

Use the following command:

• get system interface

If the DMZ address is in the same subnet with the Internal or External

interfaces it will have to be changed. Otherwise it does not need to be

set at this point. To change it use:

• set interface dmz address 10.10.10.114

• set interface dmz netmask 255.255.255.0

In the event of difficulties you can restore the factory default settings with

the following command:

• set system status reset

When you are finished with the console you can log out using the com-

mand:

• quit

Connecting to Your Network

Connect the Internal Interface to an Internal Network Hub or Switch using

a straight Ethernet cable.The Link indicator will light up if the connection is

to a 100 megabit device.

Connecting to the Internet

Connect the External Interface to the Internet by running an Ethernet

cable from the DFL-1000 External Interface to the Public Switch or Router

provided by your Internet Service Provider.

Advanced Configuration

Now that you have completed the basic network setup, the DFL-1000

should be operating with the default policy, which is to allow all traffic origi-

nating from Internal to reach outside, and deny all traffic originating from

the Internet. The default security level for Virus Protection is Low. You

can regularly go to visit tsd.dlink.com.tw web site for updating virus scan

database.

Now you are ready to begin the Advanced Configuration of the DFL-1000.

Please refer to the User Manual for more information.

Troubleshooting

At any time during the installation process if the DFL-1000 is not

responding correctly, you can shut it down and restart it.

From the web-based manager:

1. Go to System > Status.

2. Click Restart.

From the CLI:

1. Enter the command.

set system status restart

You can also cycle the power on the DFL-1000 by unplugging it and then

plugging it back in.

If these measures do not work, you can restore the factory default

settings. From the web-based manager:

1. Go to System > Status.

2. Click Reset to default and click OK.

The DFL-1000 is returned to the configuration that it had when you first switched it

on.

From the CLI:

1. Enter the command.

set system status reset

The DFL-1000 is returned to the configuration that it had when you first switched it

on.

Andere Handbücher für DFL-1000

Inhaltsverzeichnis

Andere D-Link Firewall Handbücher

D-Link

D-Link DFL-600 Bedienungsanleitung

D-Link

D-Link DFL-1100 - Security Appliance Bedienungsanleitung

D-Link

D-Link NetDefend DFL-1660 Bedienungsanleitung

D-Link

D-Link NetDefend DFL-800 Bedienungsanleitung

D-Link

D-Link DFL-700 - Security Appliance Bedienungsanleitung

D-Link

D-Link DFL-500 Bedienungsanleitung

D-Link

D-Link NetDefend DFL-260E Bedienungsanleitung

D-Link

D-Link NetDefend Firewall Series Bedienungsanleitung

D-Link

D-Link NetDefend SOHO DFL-160 Bedienungsanleitung

D-Link

D-Link DFL-200 - Security Appliance Bedienungsanleitung

D-Link

D-Link DFL-210 - NetDefend - Security Appliance Bedienungsanleitung

D-Link

D-Link DIR-330 - Wireless G VPN Router Bedienungsanleitung

D-Link

D-Link NetDefend DFL-860 Bedienungsanleitung

D-Link

D-Link DFL-1600 - Security Appliance Bedienungsanleitung

D-Link

D-Link NetDefend DFL-800 Bedienungsanleitung

D-Link

D-Link NetDefend DFL-1660 Bedienungsanleitung

D-Link

D-Link DFL-800 - Security Appliance Bedienungsanleitung

D-Link

D-Link DFL-80 Bedienungsanleitung

D-Link

D-Link NetDefend DFL-260E Bedienungsanleitung

D-Link

D-Link NetDefend DFL-860E Bedienungsanleitung

D-Link

D-Link DFL-200 - Security Appliance Bedienungsanleitung

D-Link

D-Link NetDefend DFL-260E Bedienungsanleitung

D-Link

D-Link NetDefend DFL-260E Bedienungsanleitung

D-Link

D-Link DFL-1100 - Security Appliance Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Cisco

Cisco S190 Bedienungsanleitung

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Cisco

Cisco 3110 Handbuch

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung