D-Link DMC-1001 - Power Supply - hot-plug Bedienungsanleitung

DMC-1001

Redundant Power Supply

User’s Guide

Rev. 01 (JAN. 2002)

Printed In Taiwan

RECYCLABLE

INTRODUCTION

Thank you for choosing the DMC-1001 Redundant

Power Supply of Chassis-Based Media Converter.

When the chassis is equipped with two power supplies,

both power supplies are switched on and share the

current load. In case that one of them should fail, the

other will instantaneously take 100% of the load

without any loss. Similarly, if one power supply is

removed from servicing, it can be switched off and

removed while the chassis continues functioning.

Product Features

9Efficiency: The efficiency is higher than 70% by

measured at nominal line and rated load.

9Protection: Over voltage protection; short circuit

protection.

9Power sharing and redundancy.

9Fan failure Signal: The power supply will provide

a predictive fan failure signal that detects a failure

based on reduced fan RPM.

INSTALLATION

Step 1: Connect the supplied AC power cord to the back of the

chassis.

Step 2: Attach the plug into a standard AC outlet with a voltage

range from 100~240Vac.

Step 3: Turn on the chassis system by flipping the switch beside the

receptacle to ON position. The LED on the front panel of

power supply will come on then.

.Installing and Removing the Power Supply

zTo remove a power supply out the chassis, you have to loose

the hand screw counter clockwise and pull out the power

supply from the chassis.

zTo install a power supply to the chassis, you have to fasten

the hand screw clockwise and slide in the power supply to

the chassis.

Youcanslide inand outthepowersupplyfrom thebay,

fastenorloose thehand screwclockwise orcounter

clockwise byusing hand orscrewdriver.

If the Chassis System needs to work alone, you can

stick up four Rubber foot below the chassis!

Attention!

SPECIFICATIONS

Power Supply

Input Voltage: 85VAC(60Hz)/264VAC(50Hz) label:

110V-240V

Output

Voltage: +12V

Power

Consumption 150 watts. (max.)

Dimension 185 x 160 x 85 mm

Temperature Operating: 0°~40°C,

Storage: -10°~50°C

Humidity Operating: 10% ~ 90%,

Storage: 5% ~ 90%

Overload

Protection

All outputs protected from short circuit

condition, automatic recovery

Emissions FCC Class A, CE Mark Class A,

VCCI Class A

Safty

Standard

UL 1950CSA

CSA 22.2 No.234

Andere Handbücher für DMC-1001 - Power Supply - hot-plug

Inhaltsverzeichnis

Andere D-Link Stromversorgung Handbücher

D-Link

D-Link DPS-510 Bedienungsanleitung

D-Link

D-Link DCS-80-5 Bedienungsanleitung

D-Link

D-Link RPS DPS-200 Bedienungsanleitung

D-Link

D-Link DGS-6604-SK Bedienungsanleitung

D-Link

D-Link DPS-200A Bedienungsanleitung

D-Link

D-Link DMC-1001 - Power Supply - hot-plug Bedienungsanleitung

D-Link

D-Link DPS-520 Bedienungsanleitung

D-Link

D-Link mydlink DSP-W215 Bedienungsanleitung

D-Link

D-Link mydlink DSP-W215 Bedienungsanleitung

D-Link

D-Link DIS-PWR180AC/RU Bedienungsanleitung

D-Link

D-Link DPS-520 Bedienungsanleitung

D-Link

D-Link DMC-1001 - Power Supply - hot-plug Bedienungsanleitung

D-Link

D-Link DIS-PWR40AC/RU Bedienungsanleitung

D-Link

D-Link DPS-300 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung