D-Link DES-3326 Bedienungsanleitung

DES-3326 Layer 3 Switch Example Layer 3

Configuration Guide.

Model: DES-3326

Firmware Version 1.00B19

OS Supported: Windows 95, Windows 98, Windows 98SE, Windows Me,

Windows NT 4.0 and Windows 2000.

Introduction

This guide will help you to setup a routing function to operate between two

TCPIP networks. Its important to have the latest firmware installed in the

switch before embarking on the configuration. At the time of writing this

document the firmware release was 1.00B19. Please visit the UK ftp site for

the latest firmware releases.

ftp://ftp.dlink.co.uk

Network Configuration

Fig 1. Network Configuration.

An illustration of a typical layer 3 application is shown in fig 1. above. Two

departments are segmented using layer 3 routing protocol rather than

segmented at the MAC layer. The engineering department is on ports 1 & 2.

The sales department is on ports 17 to 24.

Fig 2. Mix of Layer 2 & Layer 3

The example configuration can be further extended to include both layer 2 & 3

switches as shown in fig 2. The configuration is complete if PC1 can ping

PC2. The DES-3326 thus has achieved the act of routing between the 2

subnets. For the purpose of this document, fig 1. above will be the reference

configuration. Fig 2. is an illustration of what can be configured if layer 2

switches also exist in your network.

Configuration Procedure

Before you begin the layer 3 configuration, you will need to change the

operating mode of the switch from layer 2 to layer 3. The default setting for

the switch is layer 2. To do this, attach to the switch through its RS232

console port with HyperTerminal and login onto the switch. The default

username and password isno username and no password, simply press

return -return. You will be presented with the main menu options as shown in

fig 3.

Fig 3. Switch Main Menu

Select from the main menu 'Switch Settings'

Fig 4. Switch Settings Menu

From the switch settings menu select 'Switch Operating Mode'

Fig 5. Switch Operating Mode

Using the space bar change the operating mode from layer 2 to 'IP Routing,

support IEEE 802.1Q VLANs' as in fig 5. Apply the changes, the switch will

reboot. Reattach to the switch through HyperTerminal. Please note, you do

not need to change any of the configuration parameters in the 'Remote

management setup' leave them at there default settings, fig 6.

Fig 6. Remote Management Settings

After you have completed the above. Proceed to the next stage of the

configuration, that is to configure the VLAN's.

Fig 7. Main Menu

From the main menu select 'VLAN's'

Fig 8. VLAN Menu

Select 'Configure 802.1Q Port Settings'. You will need to configure the port

VLAN ID (PVID) before configuring the 802.1Q VLAN's. The default PVID for

all ports is set to 1. For setting up VLAN's for the engineering department use

PVID=2, for sales use PVID=3 as shown in Fig. 9.

Fig 9. 802.1Q Port Settings

After the above is completed your ready to configure the 802.1Q VLAN's. Go

to the previous menu and select 'Edit 802.1.Q VLAN's'.

Fig 10. 802.1Q VLAN's

For the VID use the same number as used for the PVID previously. You will

need to leave the default VLAN as is, ie do not change the default VID. Use

the TAB key to cursor to the VID and enter '2', again use the TAB key to

cursor to VLAN name and enter an appropriate name. In this example we

have the first octet of the IP adress. Under the membership, 'Egress' the port

by selecting E. You will need to Egress all the port members of this VLAN. In

this example only ports 1 & 2 are members. In the Tagging section, select 'U'

for Untag. This is so because adapters connected to these ports may not be

Tag compliant. Repeat the procedure for the second subnet.

Your now ready to configure you layer 3 routing configuration within the

switch. From the main menu select layer 3 IP Networking, then select 'Setup

IP Interface'

Fig 11. Layer 3 IP Networking

Fig 12. IP Interface Setup

Once again in this example we have used the fist octet for the interface name.

The IP address is the IP address of the the switch in that particular subnet, we

have choosen 192.168.0.250 MASK 255.255.255.0. The VID is the PVID set

in the VLAN configuration previously done. After the config is applied, the

screen will show you the configuration as in fig 12.

Fig 13. Subnet 192 Config

Fig 14. Subnet 212 Config

Ensure all the configurations have been applied, check the IP interfaces

addresses. If all looks okay return to the main menu and save the

configuration.

Fig. 15 Save Configuration

How to Test the Configuration

To test the configuration, do a ping test from a PC on the192 subnet to a PC

on the 200 subnet. If succesful, the layer configuration is complete. If the ping

test produces a 'request timed out' check the configuration above more

carefully. You may need to perform a factory reset and re-config the switch.

~ End of Document ~

Andere Handbücher für DES-3326

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DKVM-IP16 Bedienungsanleitung

D-Link

D-Link xStack DGS-3610 Series Handbuch

D-Link

D-Link DKVM-2 Bedienungsanleitung

D-Link

D-Link xStack DGS-3627 series Bedienungsanleitung

D-Link

D-Link DGS-1008P Bedienungsanleitung

D-Link

D-Link DGS-1250 Series Handbuch

D-Link

D-Link DXS-3326GSR - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link xStack DGS-3610 Series Bedienungsanleitung

D-Link

D-Link DGS-1016S Bedienungsanleitung

D-Link

D-Link DES-1024D Bedienungsanleitung

D-Link

D-Link xStack DGS-3600 Series Bedienungsanleitung

D-Link

D-Link DGS-1100-05PDV2 Bedienungsanleitung

D-Link

D-Link xStack DGS-3200 Series Bedienungsanleitung

D-Link

D-Link DIS-100G-5PSW Bedienungsanleitung

D-Link

D-Link DSS-5 - 10/100 Switch, Desktop Bedienungsanleitung

D-Link

D-Link DUB-H7 - Hub - USB Bedienungsanleitung

D-Link

D-Link DGS-1210-28FL Bedienungsanleitung

D-Link

D-Link DGS-1224T - Web Smart Switch Bedienungsanleitung

D-Link

D-Link DGS-1248T - Switch Bedienungsanleitung

D-Link

D-Link DGS-1024D/E1 Bedienungsanleitung

D-Link

D-Link DUB-H7 - Hub - USB Bedienungsanleitung

D-Link

D-Link mydlink Smart Plug Lite Bedienungsanleitung

D-Link

D-Link DUB-H4 Bedienungsanleitung

D-Link

D-Link DGS-3024 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung