D-Link DGS-1248T - Switch Bedienungsanleitung

Before Your Begin

This Quick Installation Guide gives step-by-step instructions for setting up the D-Link

DGS-1248T Gigabit Smart Switch. The model you have purchased may appear

slightly different from those shown in the illustrations. For more detailed information

about the switch, its components, making network connections and technical

specifications, please refer to the User’s Manual on master CD included with your

switch.

Check Your Package Contents

These are the items included with your DGS-1248T purchase:

If any of the above items are missing, please contact your reseller.

holders. Software and specifications subject to change without notice.

• DGS-1248

D-Link 48-Port 10/100/1000Mbps + 4 Combo

Mini GBIC Gigabit Smart Switch

• CD-ROM (containing Manual and Utility

Installation)

• 100-240VAC 50/60Hz

Power Adapter

Using a powe

supply with a

different voltage rating

will damage and void

the warranty for this

product.

DGS-1248T

D-Link 48-Port

10/100/1000Mbps + 4 Combo

Mini GBIC Gigabit

Smart Switch

Setup the DGS-1248T Gigabit Smart

Switch

The setup of the Switch can be performed using the following steps:

A. Install the DGS-1248T in a fairly cool and dry place. See Technical

Specification for the acceptable operation temperature and humidity

ranges.

B. Install the DGS-1248T in a site free from strong electromagnetic

field generators (such as motors), vibration, dust, and direct

exposure to sunlight.

C. Leave at least 10cm (about 4 inches) of space at the front and rear

of the hub for ventilation.

D. Visually inspect the DC power jack and make sure that it is fully

secured to the power adapter.

E. Install the DGS-1248T on a sturdy, level surface that can support

its weight, or in an EIA standard-size equipment rack.

F. When installing the Switch on a level surface, attach the rubber feet

to the bottom of each device. The rubber feet cushion the hub and

protect the hub case from scratching.

Attach the adhesive rubber pads to the bottom

Rack Mounting

The DGS-1248T can be mounted in an EIA standard-size, 19-inch rack,

which can be placed in a wiring closet with other equipments. Attach the

mounting brackets to both sides of the Switch (one at each side), and

secure them with the provided screws.

Use the screws provided. Then use screws provided with the

equipment rack to mount the Switch in the rack.

Mount the Switch in the rack

Connecting Network Cable

The DGS-1248T supports 10/100/1000Mbps Gigabit Ethernet. It runs

full/half duplex transfer mode for 10/100Mbps and full duplex transfer

mode for 1000Mbps. Each port on the DGS-1248T supports Auto-

MDI/MDI-X. Auto-MDI/MDI-X is a feature that eliminates the need for

worrying about using either a standard or crossover cable—you can

use either one—and allows any port to be an uplink port.

AC Power

The DGS-1248T can be used with AC power supply 100~240V AC,

50~60Hz. The power switch is located at the rear of the unit adjacent to

the AC power connector and the system fan. The switch’s power supply

will adjust to the local power source automatically and may be turned on

without having any or all LAN segment cables connected.

Connect The DGS-1248T Gigabit

Smart Switch To Your Network

Front Panel

10/100/1000 Base-T Mini GBIC Ports

Twisted-Pair Ports

┌────────────────────────────────────────┐ ┌──┐

1000BASE-T Twisted Pair Ports (Port 1~48)

The DGS-1248T is equipped with two Gigabit twisted pair ports that

are auto negotiable 10/100/1000Mbps and also support auto

MDI/MDIX crossover detection. These two ports can operate in half-

and full- duplex modes.

Mini GBIC Ports (Option Port 45~48)

The Switch is equipped with two Mini GBIC/SFP ports, supported

optional 1000BASE-SX/LX Mini GBIC transceivers.

Note: When the port was set to “Forced Mode”, the Auto

MDI/MDIX will be disabled.

LED Indicators

LED stands for Light-Emitting Diode.

The front panel LEDs provides instant status feedback and simplifies

monitoring and troubleshooting tasks.

LED indicators of the Switch

Power LEDs

On When the Power LED light is on, the Switch is

receiving power.

Off When the Power LED light is off, the power cord

is improperly connected.

CPU LEDs ( Management Indicator)

Blinking When the CPU is working, the System LED is

blinking.

On/Off The CPU is not working.

Ports 1 & 48 Status LEDs

Link/Act

On When the Link/Act LED lights on, the respective

port is successfully connected to an Ethernet

network.

Blinking When the Link/Act LED is blinking, the port is

transmitting or receiving data on the Ethernet

network.

Off No link.

SPEED:

(Green)

: When the green light is on, the respective port is

connected to a 1000Mbps Gigabit Ethernet

network.

(Amber)

When the Amber light is on, the respective port is

connected to a 100Mbps Fast Ethernet network.

Off : When the respective port is connected to a

10Mbps Ethernet or No link

Option Ports 45~48 Mini-GBIC Status LEDs

Link/Act

On When the Mini GBIC module is installed and

connected to a network, the Link/Act LED lights on.

Blinking When the LED is blinking, the Mini GBIC module is

receiving data on a network.

Off No link.

Installing the SmartConsole Utility

Through the Web Browser you can configure the Switch such as VLAN,

Trunking, QoS… etc.

The following instruction guides you to install the SmartConsole Utility.

1. Insert the Utility CD in the CD-Rom Drive.

2. From the Start menu on the Windows desktop, choose Run.

3. In the Run dialog box, type D:\ SmartConsole Utility \setup.exe (D:\

depends where your CD-Rom drive is located) and click OK.

4. Follow the on-screen instructions to install the utility.

5. Upon completion, go to Program Files -> SmartConsole Utility

and execute the SmartConsole Utility. (Figure 1.)

Figure 1

Configuring the Switch

The DGS-1248T has a Web GUI interface for smart switch configuration.

The Switch can be configured through the Web Browser. A network

administrator can manage, control and monitor the switch from the local

LAN. This section indicates how to configure the Switch to enable its

smart functions.

Note: Use Internet Explorer 5.5 or above Web browser to properly

access and view the configuration.

Before you configure this device, note that when the Web Smart Switch

is configured through an Ethernet connection, make sure the manager

PC must be set on the same IP network. For example, when the default

network address of the default IP address of the Web Smart Switch is

192.168.0.1, then the manager PC should be set at 192.168.0.x (where x

is a number between 2 and 254), and the default subnet mask is

255.255.255.0.

Enter IP address http://192.168.0.1 (the factory-default IP address

setting) to the address location. (Figure 2.)

Figure 2.

Or through the SmartConsole Utility, you do not need to remember the IP

Address, select the device shown in the Monitor List of the

SmartConsole Utility to settle the device on the Web Browser.

When the following dialog page appears, remain enter the default

password "admin" and press Login to enter the main configuration

window. (Figure 3.)

Figure 3.

After entering the password, the main page comes up, the screen will

display the device status. (Figure 4.)

Figure 4.

Setup Menu

When the main page appears, find the Setup menu in the left side of the

screen (Figure 5). Click on the setup item that you want to configure.

There are eleven options: System Setting, Trap Setting, Port Setting,

SNMP Setting, Password Access Control, 802.1Q VLAN, Trunking,

IGMP Snooping, 802.1D Spanning Tree, Port Mirroring, 802.1p Default

Priority, Safeguard Engine, Broadcast Storm Control, 802.1X Setting,

Static MAC, Dynamic Forwarding Table and Statistics. (Figure 5).

Figure 5.

Tool

You can also find the Tool menu on the main page (Figure 6). Click on it

and scroll down as shown in Figure 6, and you can see four options:

Reset, Config Backup & Restore, Firmware Backup & Upload and

System Reboot.

Figure 6

Andere Handbücher für DGS-1248T - Switch

Inhaltsverzeichnis

Sprachen:

Andere D-Link Schalten Handbücher

D-Link

D-Link DES-3326SR Bedienungsanleitung

D-Link

D-Link xStack DES-3800 Series Bedienungsanleitung

D-Link

D-Link DGS-3308FG - Switch Bedienungsanleitung

D-Link

D-Link DGS-3024 Bedienungsanleitung

D-Link

D-Link DUB-1340 Bedienungsanleitung

D-Link

D-Link DGS-3710 Series Handbuch

D-Link

D-Link DES-3350SR Bedienungsanleitung

D-Link

D-Link xStack DGS-3600 Series Bedienungsanleitung

D-Link

D-Link DSS-24+ Bedienungsanleitung

D-Link

D-Link DGS-3200-16 - Switch - Stackable Bedienungsanleitung

D-Link

D-Link DKVM-IP8 Bedienungsanleitung

D-Link

D-Link DFE-550TX Bedienungsanleitung

D-Link

D-Link DGS-1210-10P Bedienungsanleitung

D-Link

D-Link DGS-F1018P-E Bedienungsanleitung

D-Link

D-Link DGS-1520-52 Bedienungsanleitung

D-Link

D-Link DES-3526 - Switch - Stackable Bedienungsanleitung

D-Link

D-Link DUB-M520 Bedienungsanleitung

D-Link

D-Link xStack DGS-3420 Series Einrichtungshandbuch

D-Link

D-Link DGS-1024D G2 Bedienungsanleitung

D-Link

D-Link DKVM-222 Bedienungsanleitung

D-Link

D-Link DIR 601 - Dlink Wireless N 150 Home Router Bedienungsanleitung

D-Link

D-Link GO-SW-8G Bedienungsanleitung

D-Link

D-Link xStack DGS-3427 Bedienungsanleitung

D-Link

D-Link DGS-1100-05V2 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung