D-Link DIS-700G-28SW Bedienungsanleitung

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

DIS-700G-28SW

Industrial Layer 2+ Gigabit Managed

Switch with SFP slots

Quick Installation Guide

This document outlines the quick installation of the DIS-700G-28SW series.

Package Checklist

Please verify that the box contains the following items:

Item

Quantity

Rack-mounted Ethernet switch

Rack-mount bracket

Screws (for bracket)

ALM Terminal Block (2-pin)

Quick Installation Guide

RJ45 Ethernet Port Dust Cover

SFP Ethernet Port Dust Cover

Safety Instructions

When a connector is removed during installation, testing, or servicing, or when an energized fiber is

broken, a risk of ocular exposure to optical energy that may be potentially hazardous occurs,

depending on the laser output power.

The primary hazards of exposure to laser radiation from an optical-fiber communication system are:

Damage to the eye by accidental exposure to a beam emitted by a laser source.

Damage to the eye from viewing a connector attached to a broken fiber or an energized fiber.

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Model Layouts

Front Access Models

Front View

DIS-700G-28SW

Rear View

DIS-700G-28SW

Item

Description

System Status Indicators (LED)

Port Status Indicators (LED)

Gigabit Copper RJ45 Ports

100/1000BaseSFP Slot (Port 25 & 26)

1000BaseSFP Slot (Port 27 to 28)

Terminal Block for Alarm Relay output

Grounding Screw

DC terminal block (dual input)

Console Port

Reset Button















DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Dimensions

(unit = mm)

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Rack Mounting

When mounting the switch, practice good safety habits. Relay rack mounting normally requires at

least two people.

1. Obtain the tools required for the mounting hardware.

2. Attach the mounting brackets to the switch in one of two supported positions by using the

screws in the accessory kit.

3. From the front of the relay rack, position the switch in preferred location.

4. Secure the switch in place with the provided screws on both left and right side of mounting

bracket.

Mounting Bracket Position 1 for Standard Mount

Position 1

Position 2

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Mounting Bracket Position 2 for Standard Mount

Ground Connecting

The switch must be properly grounded for optimum system performance.

Alarm Relay Connecting

The 30VDC/1A alarm relay output contacts are located in a 2P terminal block.

The alarm relay contact is “Normal Open”, and it will be closed when detected any power failures.

Power Connecting

AC Power Connection

If you use AC power, connect the AC power cord to the AC supply socket on the rear panel, and

plug the cord into the external power source. The voltage must be 100 to 240 V (±10% tolerance).

Warning:

Ensure that all power sources to the chassis (power distribution panel) are turned off

during the connection.

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Ethernet Interface Connecting (RJ45 Ethernet)

The switch provides two types of electrical (RJ45) and optical (mini-GBIC) interfaces.

Connecting the Ethernet interface via RJ45:

To connect to a PC, use a straight-through or a cross-over Ethernet cable,

To connect the switch to an Ethernet device, use UTP (Unshielded Twisted Pair) or STP

(Shielded Twisted Pair) Ethernet cables.

Ethernet Interface Connecting (Fiber, SFP)

For a 1000 Mbps fiber port available, please use the mini-GBIC SFP. These accept plug in fiber

transceivers that typically have an LC style connector.

For a 100 Mbps fiber port (port 25 & 26 only) available, please prepare the LC connectors or SC

connectors (with the use of an optional SC-to-LC adapter).

They are available with multimode, single mode, long-haul or special-application transceivers.

DANGER:

Never attempt to view optical connectors that might be emitting laser energy.

Do not power up the laser product without connecting the laser to the optical fiber

and putting the cover in position, as laser outputs will emit infrared laser light at this

point.

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Console Connection

The Console port is for local management by using a terminal emulator or a computer with terminal

emulation software.

DB9 connector connect to computer COM port

Baud rate: 115200bps

8 data bits, 1 stop bit

None Priority

None flow control

To connect the host PC to the console port, a RJ45 (male) connector-to-RS232 DB9 (female)

connector cable is required. The RJ45 connector of the cable is connected to the CID port of

DIS-700G-28SW; the DB9 connector of the cable is connected to the PC COM port. The pin

assignment of the console cable is shown below:

Connect & Login to DIS-700G-28SW

1. Connecting to DIS-700G-28SW Ethernet port (RJ45 Ethernet port).

2. Factory default IP: 192.0.2.1

3. Login with default account and password.

Username: admin

Password: admin

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

CLI Initialization & Configuration (Optional)

1. Connecting to DIS-700G-28SW Ethernet port (RJ45 Ethernet port).

2. Enter the command: telnet 192.0.2.1

3. Login with default account and password.

Username: admin

Password: admin

4. Change the IP address with commands listed below:

CLI Command:

SYSTEM RESET

The Reset button is provided to reboot the system without the need to remove power. Under normal

circumstances, you will not have to use it. However, or rare occasions, the DIS-700G-28SW may not

respond; then you may need to push the Reset button.

enable

configure

interface vlan 1

ip-address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx

exit

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

LED STATUS INDICATIONS

LED Name

Indicator /color

Condition

1. System Status Indicators

SYS

On Green

System is working normal

Flash Green

System booting, or database saving or remote download is

in-progress

Off

System is not working or not have supply power

On Green

P1 power line has power

Flashing Green

P1 is DC power and only one pair of power is input

Off

P1 power line disconnect or does not have supply power

On Green

P2 power line has power

Off

P2 power line disconnect or does not have supply power

Alarm

On Red

Alarm event occurs

Off

No alarm

RR (Ring Role)

On Green

One of 3 Ring group is enabled and is Master role.

Off

Ring is slave role

RS (Ring Status)

On Green

Ring fail happen and detected

Off

No ring fail detected

2. Port Status Indicators

Copper port Link/Act

(Port 1 to 24)

On Green

Ethernet link up but no traffic is detected

Flashing Green

Ethernet link up and there is traffic detected

Off

Ethernet link down

Copper port Speed

(Port 1 to 24)

On Yellow

A 1000Mbps connection is detected

Off

No link or a 10 Mbps,100Mbps connection is detected

SFP port Link

(Port 25 to 28)

On Green

Ethernet link up

Flashing Green

Ethernet link up and there is traffic detected

Off

Ethernet link down

SFP Speed

(100/1000M)

(Port 25 to 28)

SFP port speed 1000Mbps

Off

SFP port speed 100Mbps or link down

DIS-700G-28SW Industrial Layer 2+ Gigabit Managed Switch with SFP slots Quick Installation Guide

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Non-modification Statement

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Caution

This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

Innovation, Science and Economic Development Canada (ISED) Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Japan Voluntary Control Council for Interference Statement

この装置は、クラス A 情報技術装置です。この装置を家庭環境で使用すると電波妨

害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求され

ることがあります。 VCCI-A

This is a Class A product based on the standard of the Voluntary Control Council for

Interference (VCCI). If this equipment is used in a domestic environment, radio interference

may occur, in which case the user may be required to take corrective actions.

CE EMI Class A Warning

This equipment is compliant with Class A of CISPR 32. In a residential environment this

equipment may cause radio interference.

Ver 1.01 (EU) 2019/12/16 GP801280X-000

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DKVM-4K - KVM Switch Bedienungsanleitung

D-Link

D-Link DES-3326S - Switch - Stackable Bedienungsanleitung

D-Link

D-Link DGS-3324SR Bedienungsanleitung

D-Link

D-Link DKVM-2KU Bedienungsanleitung

D-Link

D-Link DGS-3710 Series Handbuch

D-Link

D-Link DGS-3130-54PS Bedienungsanleitung

D-Link

D-Link DSS-200G-28MP Bedienungsanleitung

D-Link

D-Link DUB-H7 - Hub - USB Bedienungsanleitung

D-Link

D-Link xStack DGS-3620 Series Bedienungsanleitung

D-Link

D-Link DKVM-4U Bedienungsanleitung

D-Link

D-Link DGS-1248T - Switch Bedienungsanleitung

D-Link

D-Link xStack Handbuch

D-Link

D-Link xStack DGS-3620 Series Bedienungsanleitung

D-Link

D-Link DGS-3024 Bedienungsanleitung

D-Link

D-Link DES-5200 Bedienungsanleitung

D-Link

D-Link KVM-121 Bedienungsanleitung

D-Link

D-Link DES-3326SR Bedienungsanleitung

D-Link

D-Link DMS-1250 Series Handbuch

D-Link

D-Link DGS-1210-10 Bedienungsanleitung

D-Link

D-Link DGS-2205 - Desktop Switch Bedienungsanleitung

D-Link

D-Link GO-SW-5G Bedienungsanleitung

D-Link

D-Link DGS-1005D - Switch Bedienungsanleitung

D-Link

D-Link DES-7000 Series Bedienungsanleitung

D-Link

D-Link DXS-3600-16S Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung