D-Link DIS-F200G Series Bedienungsanleitung

DIS-F200G SERIES

Layer 2+ Gigabit Industrial Smart Managed

PoE Switches with Long Reach PoE Ports

Getting Started Guide for

Industrial Ethernet Switch

This document will guide you through the basic installation process

for your new D-Link Industrial Ethernet Switch.

QUICK INSTALLATION GUIDE

Documentation is also available on the D-Link website, see dlink.com.au

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 2

Before You Begin

This Quick Installation Guide gives you step-by-step instructions for setting up the

DIS-F200G Series Layer 2+ Gigabit Industrial Smart Managed PoE Switch. The model you

have purchased may appear slightly dierent from the one shown in the illustrations.

For more detailed information about the Switch, please refer to the user manual.

Package Contents

This package should include the following items:

• DIS-F200G Series Switch

• Power terminal block

• Relay terminal block

• DIN rail mounts (installed)

• Quick Installation Guide

If any of the above items are damaged or missing, please contact your local D-Link Reseller.

HARDWARE OVERVIEW

LED Status Description

P1, P2 On The corresponding power source is connected

O The corresponding power source is not connected or failed

SYS Flashing The system is operating correctly

O or On The system is not responding

ALM On Alarm has been triggered

O No Alarm

F1, F2 On or Flashing SFP port connected and active

O SFP port not connected

LED Indicators

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 3

Power Terminal Block Relay Terminal Block

Reset Button

RJ45 Console Port

Shortcut Buttons

(DIP Switch)

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 4

Mounting the Switch on a DIN Rail

Before beginning either mounting or removing the DIS-F200G from a DIN rail, please

ensure that the DIN rail is level and that the DIN rail mounting kit is installed correctly on

the DIS-F200G. Use the following instructions to install the DIS-F200G on a DIN rail:

1. With the back of the DIS-F200G facing the DIN rail, lower the top part of the rail

mounting kit onto the DIN rail.

2. Push the DIS-F200G vertically down and rotate the bottom of the DIS-F200G towards

the DIN rail, to attach the Switch to the DIN rail.

Use the following instructions to remove the DIS-F200G from a DIN rail:

1. Push the DIS-F200G vertically down to create enough space at the bottom of the rail

mounting kit to remove the DIS-F200G from the DIN rail.

2. Rotate the DIS-F200G upwards to remove the bottom of the rail mounting kit from the

rail, and lift the DIS-F200G upwards to remove the whole of the Switch from the DIN rail.

Grounding the Switch

To use the DIS-F200G safely, it needs to be grounded. Insert a grounding wire into the termi-

nal grounding connection and use a at head screwdriver to tighten the screw to secure the

wire. Attach the other end of the grounding cable to an appropriate grounding source.

Grounding Wire

Before You Begin

Observe the following precautions to help prevent shutdowns, equipment failures, and

personal injury:

• Install the DIS-F200G in a cool and dry place. Refer to the technical specications in the

user manual for the acceptable operating temperature and humidity ranges.

• Leave at least 10 cm of space at the top, rear and bottom of the Switch for ventilation.

• Visually inspect the power connector and make sure that it is fully secured to the

power cord.

• Do not stack any devices on top of the Switch.

It is also recommended that power and grounding requirements are investigated before

mounting the Switch.

HARDWARE INSTALLATION

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 5

Using the Terminal Connections

Before proceeding, ensure that all power sources have been disconnected from the

DIS-F200G, and that the power source you are wiring to the DIS-F200G is also disconnected.

Use the following instructions to power the DIS-F200G using the terminal connections:

1. Before continuing, consult the diagram above to decide which wires from the power

source need to connect to which contacts on the terminal block. Note that two power

sources can be used; one inserted into -/+ (labelled PWR1) and the other inserted into

-/+ (labelled PWR2). If you only wish to use one power source, insert the wires into

-/+ (PWR1).

2. Using a at head screwdriver, loosen the connections in the terminal block by un-screwing

the terminal connections that you wish to use.

3. Insert the wires into the terminal connections and use the screwdriver to tighten the

screws to secure the wires.

4. Re-insert the terminal block into the terminal block socket on the DIS-F200G.

Connecting to a Power Source

The DIS-F200G can be powered using the in-built terminal connector. This allows dual

power inputs, using wires from the power source(s) screwed-in to the terminal connections.

Input voltage is 48 to 56V DC

The Switch oers built-in over current protection and power supply reverse connection

protection.

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 6

The DIS-F200G can be managed by using the Web User Interface (Web UI), Console Port,

Telnet, SSH, or Simple Network Management Protocol (SNMP).

For management, each Switch must be assigned its own IP address, which is used for

communication with the management PC.

Web User Interface

Once the Switch has been successfully installed, you can begin conguration and monitor

Switch status using a web browser. Supported browsers include Firefox, Chrome and Safari.

You need the following equipment to access the Web UI of your device:

• A PC with an RJ-45 Ethernet connection

• A standard Ethernet cable

1. Connect the Ethernet cable to any of the ports on the Switch’s front panel and to

the Ethernet port on the PC.

2. Congure the PC’s IP address to be in the same network segment as the Switch.

The Switch’s default IP address is 192.168.254.1, with subnet mask 255.255.255.0.

For example, to connect to the Switch using the default settings, your PC should have

an IP address in the range: 192.168.254.2-254 and a subnet mask of 255.255.255.0.

3. Open a web browser and enter http://192.168.254.1/ in the address box.

4. Log in to the switch. To do this, enter admin as the default user name and admin as

default password. It is recommended to apply a secure strong password to“admin”

account under System Settings > User Management.

MANAGEMENT OPTIONS

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 7

Console

To connect to the Switch’s console, use a RS-232 serial to RJ-45 cable. A terminal emulation

program is required to connect to the console port on the Switch. These are widely available

and can be easily downloaded from the Internet.

Using following steps to connect to Switch’s console port:

1. Connect the RS-232 serial interface to the serial port of the management PC.

2. Connect the RJ-45 interface to the console port of the Switch.

3. Open a terminal emulation program on the management PC and congure the

properties of the connection as follows:

• Speed: 115200 baud

• Data bits: 8

• Parity: None

• Stop bits: 1

• Flow Control: None

4. Connect to the Switch and the Command Line Interface (CLI) should be available.

When prompted to log in, enter admin as the default user name and password.

Shortcut Buttons (DIP Switches)

Some Switch settings can be applied using the Shortcut Buttons (DIP Switches), without

the need to log into the Switch interface.

DIP Switch Function when in ON position

AI Loop

Protect

Enables detection of connection loops on the network, disables ports

if detected, preventing broadcast storms.

AI PoE

Automatically restart a remote device by disabling and re-enabling

PoE on the port if it detects the remote device has locked up

(no incoming trac).

AI VLAN

Isolates RJ45 ports from each other, suppress network storms and

improves network performance. Uplink SFP ports continue to

communicate with all ports.

AI Extend Enables Long Reach PoE delivery up to 250m on PoE ports. Port speed

changes to 10Mbps (Cat 5 or better cabling is recommended).

QUICK INSTALLATION GUIDE | DIS-F200G SERIES 8

SAFETY INSTRUCTIONS

The following general safety guidelines are provided to help ensure your own

personal safety and protect your product from potential damage. Remember to

consult the product user instructions for more details.

• Static electricity can be harmful to electronic components. Discharge static

electricity from your body (i.e. touching grounded bare metal) before touching

the product.

• Do not attempt to service the product and never disassemble the product.

For some products with user replaceable battery, please read and follow the

instructions in the user manual.

• Do not spill food or liquid on your product and never push any objects into

the openings of your product.

• Do not use this product near water, areas with high humidity or condensation

unless the product is specically rated for outdoor application.

• Keep the product away from radiators and other heat sources.

• Always unplug the product from mains power before cleaning and use a dry

lint free cloth only.

Device Reset

If you have any problems accessing the DIS-F200G, it can be reset using the following

instructions:

Press and hold the reset button for 2 to 10 seconds. After releasing the button the SYS LED

light will stop ashing and after a moment will start ashing rapidly indicating a restart.

After restart the DIS-F200G will be reset to factory defaults.

Additional Information

You can refer to the user manual or visit https://support.dlink.com.au/ for more support.

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link DUB-M610 Bedienungsanleitung

D-Link

D-Link DXS-3600-32S Bedienungsanleitung

D-Link

D-Link DES-1005P Bedienungsanleitung

D-Link

D-Link DKVM-8E Bedienungsanleitung

D-Link

D-Link xStack DGS-3400 Series Bedienungsanleitung

D-Link

D-Link DGS-1024TG Bedienungsanleitung

D-Link

D-Link DGS-1100-05PD Bedienungsanleitung

D-Link

D-Link xStack DES-3800 Series Bedienungsanleitung

D-Link

D-Link DXS-3250 - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link TM DES-6500 Bedienungsanleitung

D-Link

D-Link DGS-1026MP Bedienungsanleitung

D-Link

D-Link DGS-3130 Series Bedienungsanleitung

D-Link

D-Link DGS-1100-26MP Bedienungsanleitung

D-Link

D-Link xStack DES-6500 Bedienungsanleitung

D-Link

D-Link DGS-1005D - Switch Bedienungsanleitung

D-Link

D-Link DGS-1210-10 Bedienungsanleitung

D-Link

D-Link GS-1510-28P Bedienungsanleitung

D-Link

D-Link DGS-1100-10MP Bedienungsanleitung

D-Link

D-Link DIS-100G-10S Bedienungsanleitung

D-Link

D-Link DUB-CR200 Bedienungsanleitung

D-Link

D-Link DGS-1210/ME series Bedienungsanleitung

D-Link

D-Link DGS-1216T - Switch Bedienerhandbuch

D-Link

D-Link DFE-2600 Series Bedienungsanleitung

D-Link

D-Link DES-3350SR Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

Vimar

Vimar 6592 Montageanleitung