D-Link DXS-3600-16S Bedienungsanleitung

Quick Installation Guide

Краткое руководство по установке

3 Fan, AC Power Supply, 1 Expansion Slot, 8-Port 10GBase-X SFP+,

3 Management Stacked Switch /

Управляемый стекируемый коммутатор 3 уровня с 8 портами

10GBase-X SFP+, 1 слотом расширения, источником питания AC и

3 вентиляторами

DX -3600-16

Introduction

This Quick Installation Guide gives instructions for setting up the D- ink DXS-3600-16S switch. The model

you have purchased may appear slightly different from those shown in the illustrations. For more detailed

information about the device, its components, making network connections and technical specifications,

please refer to the User Manual.

Package Contents

• DXS-3600-16S Switch

• Power Cord

• AC power supply module

• 3 Fan modules

• DB-9 to RJ-45 console cable

• 4 Rubber Feet

• 2 Mounting Brackets

• Mounting kit

• Quick Installation Guide

• Warranty Certificate

• CD ROM

If any of the above items are damaged or missing, please contact your local reseller for replacement.

Hardware Overview

Front Panel

Port Description

SD Card Slot This port can be used to insert an external SD memory card. The maximum

capacity SD card that can be inserted into this port is 32 Gb.

Management port (MGMT) This is a 10/100/1000 Mbps Out-Of-Band management port that can be used to

configure this switch without being connected to the network.

Console Port This port is an RJ-45 connection port that can be used to connect to the Command

ine Interface (C I) of this switch for configuration, management and monitoring.

This port uses a special console cable (included with the packing) with a DB-9

interface to connect the Switch to a PC’s COM port.

Ports 1-8 This switch is equipped with SFP/SFP+ ports. These ports can operate at 10 Gbps

speeds and support a vast collection of SFP, WDM SFP, SFP+, WDM SFP+ and

QSFP+ transceivers.

Expansion Module Slot This slot can be equipped with several kinds of additional modules. These modules

are not included and should be bought separately:

• DXS-3600-EM-4XT (Four 10GBase-T Copper ports).

• DXS-3600-EM-8T (Eight 1000Base-T Copper ports).

• DXS-3600-EM-4QXS (Four 40Gbps QSFP+ transceiver slots).

• DXS-3600-EM-8XS (Eight 10Gbps SFP+ transceiver slots).

LED Indicators

LED Indicative Colour tatus Description

Power 1,

Power 2

Green /

Amber

Solid Green Power on.

Solid Amber Power supply fails.

ight off Power off.

Management

(MGMT)

Green Solid Green A link to the management port was successfully established.

Blinking Green Activity on this port is taking place.

ight off There is no link present or when this interface was shutdown from within

the switch’s configuration.

Console Green Blinking Green During the Power-On Self Test (POST).

Solid Green A user is logged in through the console port.

ight off After the POST finished successfully and no user is connected to the

console port.

Fan1, Fan2,

Fan3

Green /

Amber

Solid Green When the fan is operating normally.

Solid Amber When the switch is booting up or when a diagnostics test is taking place.

Blinking Amber When a fan fails.

ight off When the fan is not receiving power.

SD Green / Red Solid Green If a Secure Digital (SD) card is plugged in.

Blinking Green The Switch is reading or writing data to and from the SD card.

ight off No SD card is plugged into the SD port.

Solid Red An SD card failure has been detected.

ink/Act Green /

Amber

Solid Green There is a secure connection to a 10 Gbps Ethernet device at any of the

ports.

Blinking Green A 10 Gbps port is active.

Solid Amber There is a secure Ethernet connection to a 1 Gbps Ethernet device at

any of the ports.

Blinking Amber A 1 Gbps port is active.

ight off There is no link or activity.

Rear Panel

Component Description

Power Supply Module Slots These slots can be equipped with two kinds of additional modules. Only one power

supply module is included. Any additional modules should be bought separately.

• DXS-PWR300AC (300W AC power supply tray with front-to-back airflow).

• DXS-PWR300DC (300W DC power supply tray with front-to-back airflow).

Fan Module Slots • DXS-3600-FAN-FB (normal fan tray with front-to-back airflow).

Installation

Desktop or helf Installation

When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached

on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and

the objects around it.

Rack Installation

The switch can be mounted in a standard 19-inch rack using the provided mounting brackets.

How to install the mounting brackets onto the switch (figure above) and onto the rack (figure below):

1. Fasten the mounting brackets A and B to the sides of the switch using the screws provided, as seen in the

figure above.

2. Fasten the mounting bracket C in the appropriate open space in the rack using the screws provided, as

seen in the figure below.

3. Simply slide the switch (fastened bracket B into fastened bracket C) into the rack.

4. astly, fasten mounting bracket A to the rack using the screws provided.

Make sure that there is adequate space around the Switch to allow for proper air flow, ventilation, and

cooling.

Installing Transceivers into the Transceiver Ports

The Switch is equipped with Small Form-factor Pluggable plus (SFP+) ports, which supply connecting SFP,

WDM SFP, SFP+, WDM SFP+ and QSFP+ transceivers.

Connecting to Power

Installing an AC Power Module

Connect the one end of the AC power cord supplied to the AC power connector and the other end into a

properly grounded electrical outlet. The switch will automatically adjust the AC power setting to adapt to any

voltage supply in the range from 100~240VAC at 50~60Hz.

In addition, an optional second AC power supply module can be plugged into the second power supply

module slot. When the primary AC power connection fails, the secondary AC power connection will take over

all the power immediately and automatically. The AC power supply modules are hot-swappable, meaning,

that they can be inserted and removed while the switch is powered on.

Install an AC Power Supply Module as shown on the picture below.

Installing a DC Power Module

This switch supports a unique dual power input feature. The DC power module will be activated if the AC

power module turns off.

1. Install a DC Power Supply Module. Use the grounding screw on the DC Power Module and a minimum of

18 AWG stranded copper wire to ground the switch.

2. Connect the one end of the DC power cord supplied to a DC power module, that will be activated when

the AC power is not working, and to a power source (-48VDC/5.2A). Please make sure that connection

polarity (positive and negative) is correct.

The DC power and AC power of the device will back up each other immediately when one of the power

sources fails. If both power sources fail, unplug the switch. When the power source has been restored, plug

the switch’s power back in.

NOTE: the Power Modules all support a specific airflow direction. This air-flow direction must be the same as

the Fan Module installed. By default the airflow direction of the Power Module and Fan Module installed is

front-to-back.

Installing Fan Modules into the Fan Module Ports

ocated on the rear panel of this switch there are three fan module ports.

The user can easily remove and insert fan modules into these ports.

witch Connections

witch to End Node

End node is a generic name for edge networking devices that will be connected to this switch. Typical

examples of end nodes are Personal Computers (PCs), Notebooks, Access Points, Print Servers, VoIP

Phones and more. Each end node will be outfitted with a 10/100/1000 Mbps, RJ-45, networking port.

Normally end nodes will connect to this switch by using a standard twisted-pair, UTP/STP, network cable.

After a successful connection, the corresponding ink/Act light will illuminate and blink to indicate that packet

activity is taking place on that port.The diagram below displays a typical end node connected to the Switch.

witch to another witch

Another popular configuration is to connect this switch to another switch. This network typography is

considered when one Switch does not have enough ports to cater for all the end nodes in the network. There

is a great deal of flexibility in the type of cabling that can be used to interlink switches.

Two or more switches can also be interlinked using fiber-optic cables or direct-attached cables via the

switch’s SFP and SFP+ ports. astly two or more switches can also be interlinked using QSFP+ interfaces

supported by the DXS-3600-EM-4QXS optional modules.

witch tacking

The DXS-3600-16S supports stacking 4 switches together while being managed by one IP address through

Telnet, the Web User Interface, the RJ-45 console port or through SNMP. This cost effective switch provides

an affordable solution for administrators to upgrade their networks using the DXS-3600-EM-4QXS module to

scale and stack the switches.

• Duplex Chain – The Duplex Chain topology stacks switches together in a chain-link format. Each switch in

a chain is connected to the upper and the lower units, while the upper and the lower switches are not

connected. If there is a break in the chain, then data transfer will obviously be affected.

• Duplex Ring – The Duplex Ring stacks switches in a ring or circle format. Each switch in a chain is

connected to the upper and the lower units, the upper and the lower switches are also connected. This

topology is very resilient due to the fact that if there is a break in the ring, data can still be transferred through

the stacking cables between switches in the stack.

The DXS-3600-EM-4QXS module uses the last two QSFP+ ports to make the following stacking topologies.

The figure below illustrates how switches can be stacked in a Duplex Chain formation using the

DXS-3600-EM-4QXS module.

The figure below illustrates how switches can be stacked in a Duplex Ring formation using the

DXS-3600-EM-4QXS module.

witch to a erver

When configuring a network, users will most likely have to add a server or two to this switch. Generally, any

port on this switch can be used to connect to a server.

Andere Handbücher für DXS-3600-16S

Inhaltsverzeichnis

Sprachen:

Andere D-Link Schalten Handbücher

D-Link

D-Link Nuclias DNH-100 Bedienungsanleitung

D-Link

D-Link DSS-200G-28MP Bedienungsanleitung

D-Link

D-Link DES-1026G/E1A Bedienungsanleitung

D-Link

D-Link xStack DGS-3420 Series Bedienungsanleitung

D-Link

D-Link DGS-1005P/A1A Bedienungsanleitung

D-Link

D-Link Dis-200G Series Bedienungsanleitung

D-Link

D-Link DES-105 Bedienungsanleitung

D-Link

D-Link DGS-1024A Bedienungsanleitung

D-Link

D-Link DMS-107/E Bedienungsanleitung

D-Link

D-Link DGS-1008P Bedienungsanleitung

D-Link

D-Link DKVM-8E Bedienungsanleitung

D-Link

D-Link DUB-H4 - Hub - USB Bedienungsanleitung

D-Link

D-Link xStack DES-6500 Bedienungsanleitung

D-Link

D-Link DGS-1005D - Switch Bedienungsanleitung

D-Link

D-Link DGS-3130-54TS Bedienungsanleitung

D-Link

D-Link DGS-1510-52XMP Bedienungsanleitung

D-Link

D-Link DES-3226SM - 1000Mbps Ethernet Switch Bedienungsanleitung

D-Link

D-Link DES-3528 - xStack Switch - Stackable Bedienungsanleitung

D-Link

D-Link DES-3205 Handbuch

D-Link

D-Link DGS-1024D/E1 Bedienungsanleitung

D-Link

D-Link DGS-1250-52XMP Bedienungsanleitung

D-Link

D-Link xStack DGS-3620-28SC Bedienungsanleitung

D-Link

D-Link DWS-3024 Bedienungsanleitung

D-Link

D-Link DGS-3630-28SC Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung