D-Link EasySmart DGS-1100-05 Bedienungsanleitung

1Product Introduction D-Link Smart Managed Switch User Manual

1 Product Introduction

Thank you and congratulations on the purchase of your new D-Link Smart Managed Switch.

D-Link's next generation Smart Managed switch series blends plug-and-play simplicity with exceptional

value and reliability for small and medium-sized business (SMB) networking. All models are housed in a

robust metal case with easy-to-view front panel diagnostic LEDs.

Flexible Port Configurations. The DGS-1100 series is the new generation of Smart Managed Switches,

featuring 5 to 8 10/100/1000 Mbps.

D-Link Green Technology. The DGS-1100 Series features D-Link Green Technology which helps

conserve power without sacrificing operational performance. Using IEEE 802.3az Energy Efficient Ethernet

(EEE), the DGS-1100 Series saves power by automatically putting inactive ports into a sleep mode.

Extensive Layer 2 Features. Designed as comprehensive L2 devices, these switches support a variety of

functions such as FDB, VLAN, Spanning Tree, and Loopback Detection to enhance performance and

network resilience.

Traffic Segmentation and QoS.The switches support 802.1Q VLAN standard tagging to enhance network

security and performance. The switches also support 802.1p priority queues, enabling users to run

bandwidth-sensitive applications such as streaming multimedia by prioritizing that traffic in network. The

Surveillance VLAN will place the video traffic from pre-defined IP surveillance devices to an assigned VLAN

with higher priority, so it can be separated from normal data traffic.

Network Security. Storm Control can help to keep the network from being overwhelmed by abnormal

traffic. Meanwhile, Port Security provides administrators with an additional layer of security to prevent

unauthorized users from accessing the network.

Versatile Management. The DGS-1100-05/05PD/08/08PD feature an intuitive, web-based management

interface that allows administrators to remotely control their network down to the port level. The D-Link

Network Assistant (DNA) easily allows administrators to discover multiple D-Link Smart Managed Switches

within the same L2 network segment and display them on-screen for instant access. With this utility, users

do not need to change the IP address of their PC. This allows for simultaneous configuration and basic

setup of all discovered devices, including password changes and firmware upgrades.

DGS-1100-05

5-Port 10/100/1000Mbps Smart Managed Switch.

Front Panel

Figure 1.1 – DGS-1100-05 Front Panel

Power LED: The Power LED lights up when the Switch is connected to a power source.

Link/Act/Speed LED (Ports 1-5): 10/100/1000 Mbps ports to connect Ethernet devices to the switch.

1 Product Introduction D-Link Smart Managed Switch User Manual

Rear Panel

Figure 1.2 – DGS-1100-05 Rear Panel

Power: Input for a 5V/1A AC adapter.

Reset: Press the Reset button for 1 to 5 seconds to reboot the Switch. Press the Reset button for 6 to10

seconds to reset the Switch back to the default settings. The LED will light up solid amber for 2 seconds.

When pressing the Reset button for longer than 10 seconds, the device will enter loader mode and the LED

will light up solid green for 2 seconds. If the device cannot reboot, it will automatically enter loader mode.

Alternatively, you can press Reset to power up the device and enter loader mode.

Kensington Lock: This is used to attach a physical Kensington security lock.

GND: This is used to connect the Switch to ground.

DGS-1100-05PD

2-Port 10/100/1000Mbps PoE and 3-Port 10/100/1000Mbps with 1 PD port Smart Managed Switch.

Front Panel

Figure 1.3 – DGS-1100-05PD Front Panel

Power LED: The Power LED lights up when the Switch is connected to a power source. If the Power LED is

Blinking, PoE Pass Through is Off.

Link/Act/Speed LED (Ports 1-5):

Flashing: Indicates a network link through the corresponding port.

Blinking: Indicates that the Switch is either sending or receiving data to the port.

Green: Indicates that the port is running at 1000M.

Amber: Indicates that the port is running at 10/100M.

Light off: No link.

PoE PSE LED (Port 1-2):

Solid Green: PD device insert and power feeding.

Solid Amber: PD device insert but failure occurs.

Light off: No PD device insert.

PoE PD (Port 5):

Solid Green: Receiving power from PSE per 802.3at.

Solid Amber: Receiving power from PSE per PSE.

Light off: No link.

Reset: Press the Reset button for 1 to 5 seconds to reboot the Switch. Press the Reset button for 6 to10

seconds to reset the Switch back to the default settings. The LED will light up solid amber for 2 seconds.

When pressing the Reset button for longer than 10 seconds, the device will enter loader mode and the LED

will light up solid green for 2 seconds. If the device cannot reboot, it will automatically enter loader mode.

Alternatively, you can press Reset to power up the device and enter loader mode.

1Product Introduction D-Link Smart Managed Switch User Manual

Rear Panel

Figure 1.4 – DGS-1100-05PD Rear Panel

Power: Use RJ45 to connect the PD port (port 5) and Power over Ethernet Adapter Kit.

Kensington Lock: This is used to attach a physical Kensington security lock.

GND: This is used to connect the Switch to ground.

NOTE: The power budget is 18 Watts with 802.3at and 8 Watts with

802.3af for DGS-1100-05PD.

DGS-1100-08

8-Port 10/100/1000Mbps Smart Managed Switch.

Front Panel

Figure 1.5 – DGS-1100-08 Front Panel

Power LED: The Power LED lights up when the Switch is connected to a power source.

Link/Act/Speed LED (Ports 1-8): 10/100/1000 Mbps ports to connect Ethernet devices to the switch.

Rear Panel

Figure 1.6 – DGS-1100-08 Rear Panel

Power: Input for a 5V/1A AC adapter.

Reset: Press the Reset button for 1 to 5 seconds to reboot the Switch. Press the Reset button for 6 to10

seconds to reset the Switch back to the default settings. The LED will light up solid amber for 2 seconds.

When pressing the Reset button for longer than 10 seconds, the device will enter loader mode and the LED

will light up solid green for 2 seconds. If the device cannot reboot, it will automatically enter loader mode.

Alternatively, you can press Reset to power up the device and enter loader mode.

Kensington Lock: This is used to attach a physical Kensington security lock.

GND: This is used to connect the Switch to ground.

DGS-1100-08P

8-Port 10/100/1000Mbps PoE Smart Managed Switch.

1 Product Introduction D-Link Smart Managed Switch User Manual

Front Panel

Figure 1.7 – DGS-1100-08P Front Panel

Power LED: The Power LED lights up when the Switch is connected to a power source.

Reset: Press the Reset button for 1 to 5 seconds to reboot the Switch. Press the Reset button for 6 to10

seconds to reset the Switch back to the default settings. The LED will light up solid amber for 2 seconds.

When pressing the Reset button for longer than 10 seconds, the device will enter loader mode and the LED

will light up solid green for 2 seconds. If the device cannot reboot, it will automatically enter loader mode.

Alternatively, you can press Reset to power up the device and enter loader mode.

Link/Act/Speed LED (Ports 1-8):

Flashing: Indicates a network link through the corresponding port.

Blinking: Indicates that the Switch is either sending or receiving data to the port.

Green: Indicates that the port is running at 1000M.

Amber: Indicates that the port is running at 10/100M.

Light off: No link.

PoE MAX. LED:

Light up: Indicates the power output to PDs is over 57W. No additional PDs can be powered for

safety consideration.

Blinking: Indicates if the user unplugged certain PDs and made the PoE power budget left over 7W,

the PoE MAX LED will blink 5 seconds.

Light off: Indicates the power budget is using less than 57W.

PoE LED (Ports 1-8):

Green: Indicates the PoE powered device (PD) is connected and the port supplies power

successfully.

Red: The PoE port has failed, possibly due to:

1. PoE total power budget shortage.

2. Over current: Exceeds the power current of powered device's classification.

3. Short circuit: Short circuit has been performed on a powered device.

Light off: Indicates no Powered Device (PD) connected.

PoE Mode LED (Port 1-8):

Solid Green: PD device insert and power feeding.

Solid Amber: PD device insert but failure occurs.

Light off: No PD device insert.

Rear Panel

Figure 1.8 – DGS-1100-08P Rear Panel

Power: Input for a 54V/1.574A AC adapter.

Kensington Lock: This is used to attach a physical Kensington security lock.

GND: This is used to connect the Switch to ground.

1Product Introduction D-Link Smart Managed Switch User Manual

NOTE: The power budget is 64 Watts for DGS-1100-08P.

LED Indicators

The Switches feature LED indicators for Power and Link/Act for each port. The following shows the LED

indicators for the DGS-1100-05/05PD/08/08PD switches along with an explanation of each indicator.

Figure 1.9 –LED Indicators on DGS-1100 series

Location Indicator LED Color Status Description

Per Device

Power Green

Solid Light The device is powered on.

Blinking PoE Pass Through Off (DGS-1100-

05PD only)

Light off The device is powered off.

PoE Max.

(Only DGS-1100-

08P) Red

Solid Light

When the power output to PDs is over

57W. No additional PDs can be

powered for safety consideration.

Blinking

If the user unplugged certain PDs and

made the PoE power budget left over

7W, the PoE MAX LED will blink 5

seconds.

Light off

When the power budget is using less

the 57W.

LED Per

10/100/1000

Mbps Port Link/Act/Speed Green/Amber

Solid Green

Indicates there is a 1000 Mbps

connection on this port.

Blinking

Green

Indicates data is being processed on

this port at 1000 Mbps.

Solid Amber

Indicates there is a 10/100 Mbps

connection on this port.

Blinking

Amber

Indicates data is being processed on

this port at 10/100 Mbps.

Light off

Indicates there is no active link on this

port.

LED Per PoE Port

PoE Status Green/Amber

Solid Green PD device insert and power feeding.

Solid Amber

PD device insert but failure occurs.

(PSE can’

t provide power to PD due to

PD error or power budget is not

enough.)

Light off No PD device inserts.

LED Per PD Port

(DGS-1100-05PD

only) PD Status Green/Amber Solid Green Receiving power from PSE per 802.3at

Solid Amber

Receiving power from PSE per PSE.

1 Product Introduction D-Link Smart Managed Switch User Manual

Light off No link.

Andere Handbücher für EasySmart DGS-1100-05

Dieses Handbuch passt für folgende Modelle

Andere D-Link Schalten Handbücher

D-Link

D-Link DES-1228P - Web Smart Switch Bedienungsanleitung

D-Link

D-Link DGS-1210/ME series Bedienungsanleitung

D-Link

D-Link DES-1008F Bedienungsanleitung

D-Link

D-Link 55443 Bedienungsanleitung

D-Link

D-Link DES-1018P Bedienungsanleitung

D-Link

D-Link DES-1008D Bedienungsanleitung

D-Link

D-Link DGS-3630-52TC Bedienungsanleitung

D-Link

D-Link DWS-1008 Bedienungsanleitung

D-Link

D-Link DGS-3208F Bedienungsanleitung

D-Link

D-Link Web Smart Switch DGS-1210-16 Bedienungsanleitung

D-Link

D-Link DGS-1052 Bedienungsanleitung

D-Link

D-Link DGS-3620-28PC-SI Bedienungsanleitung

D-Link

D-Link DXS-3400 SERIES Bedienungsanleitung

D-Link

D-Link DGS-1016A Bedienungsanleitung

D-Link

D-Link DES-3250TG Bedienungsanleitung

D-Link

D-Link DGS-1100-10MP Bedienungsanleitung

D-Link

D-Link DGS-3120-24PC-SI Handbuch

D-Link

D-Link DUB-2240 - Wireless USB Hub Bedienungsanleitung

D-Link

D-Link DES-7200 Bedienungsanleitung

D-Link

D-Link xStack DES-3228PA Bedienungsanleitung

D-Link

D-Link DGS-1210-52MP Bedienungsanleitung

D-Link

D-Link DGS-3324SR Bedienungsanleitung

D-Link

D-Link DES-3624i Bedienungsanleitung

D-Link

D-Link DXS-3600 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung