D-Link DVG-G1402S - Wireless Broadband VoIP Router Kurzanleitung

DVG-G1402S Configuration for GOtalk

In the following guide we will cover all of the settings required to configure your DVG-G1402S with your

GOtalk VoIP Account.

Factory Reset

It is recommended to factory reset your router before we proceed with the correct settings to ensure that

all the settings that we enter are stored correctly. To factory reset the unit power on the unit and wait for

it to be in a system idle state (about 30-40 seconds after power on) then press and hold the Factory Reset

button. Continue to hold the Factory Reset button for 10-15 seconds then release; this will then restart

the unit In a Factory Default state.

Reset Button is shown above by the red arrow

Accessing the Web Interface

Now to configure your unit from scratch we will need to connect to the interface via a Web Browser. Any

browser will be fine but for this guide we will be using Internet Explorer 6.0 (IE6). To log into the router

open up IE6 and type “http://192.168.15.1” into the address bar. This will now prompt you for a

username and password to configure the DVG-G1402S as shown below:

Username: “admin”, Password: “admin”

You will now need to enter the username and password to access the device. The username will be

“admin” and the password is also “admin”. Once you have entered the username and password press the

OK button.

Configuring the Connection to the Internet

Now that we have accessed the DVG-G1402S’s Web Interface we will now need to configure the router for

Internet connection. Select Home tab on top and then click on WAN button on the left.

You will see several options for different types of Internet connections. It is very common for broadband

modems to carry out the authentication process, so all you need to do on your router is to set it to the

“Dynamic IP Address” option (it is selected by default). If your provider requires PPPoE login and your

modem does not have PPPoE built in (so you had to run PPPoE client on your computer when the modem

was connected to your PC), select the PPPoE option. Specify your ISP’s account username and password.

If you have one of the recent broadband modems which are capable of handling the authentication with

your ISP, leave your router on the “Dynamic IP” option.

Click on Apply when done.

P.S. If you are connecting to Bigpond Cable you will need to select the “Dynamic IP” option in the router

and run the login software on your computer(s). We recommend using the BPALogin client:

http://www.dlink.com.au/tech/faqs/default.asp?model=DVG-G1402S&TemplateId=23678

Configuring the SIP Server for GOtalk

We now need to configure the SIP Settings for your GOtalk VoIP Account. This is done by clicking on the

Home tab at the top of the page and then selecting the VoIP button in the left hand navigation bar. You

should see the below page appear:

From the above selection press on Server Configuration. This will now bring up the SIP Server

configuration page as shown over the page. We will need to change the below settings:

Server FQDN: Enabled

Domain Name: sip.gotalk.com

Secondary Server FQDN: Enabled

Secondary Domain Name: sip.gotalk.com

Secondary Port: 5060

Outbound Proxy State: Enabled

Outbound Proxy Sever FQDN: Enabled

Outbound Proxy Domain Name: sip.gotalk.com

Outbound Proxy Port: 5060

Service Domain: sip.gotalk.com

User Parameter Phone: Disabled

Once all of the settings have been entered it should look like the below, if all is correct then click on the

Apply button to save these changes.

In order to save these changes permanently we will need to do a Reboot of that router but for now just

click on the OK button and we will Save the settings and Reboot the router when all settings are

completed.

Ok now that we have changed all of the SIP Server settings scroll to the bottom of the page and click on

the Back button to return to the main VoIP configuration page.

Configuring the VoIP Phone Account

Now that we have configured the correct values for the GOtalk SIP Server we can now setup the Phone

Account, to do this select User Agent. This will now show the below page and allow us to setup the

Phone Number and logins for VoIP account.

We now need to enter in your settings to get your account to become active. Below is a list of the settings

that you will need to enter into this page:

Same Phone Number: Enabled

Phone Number: <GOtalk Username>

Display Name: <GOtalk Username> or a name to be shown while using Caller ID

Authentication Username: <GOtalk Username>

Password: <GOtalk Password>

Retype Password: <GOtalk Password>

** Please note that you can find your GOtalk Username and Password on a white sticker on the underside of the DVG-G1402S **

Once you have entered all of the above settings into the unit click on the Apply button to Save the

settings. Once again you will see the below message box appear, just click on OK.

We have now configured the unit with all the SIP Server Settings and the Phone Account Settings. The

last thing left to do is save and reboot the unit.

Saving the Settings and Restarting the Router

In order to make all of the above changes effective and save them permanently we will need to click on

Tools at the top of the page then click on Reboot from the left hand navigation bar. This will now show the

below page:

Now click on the Reboot button. This will then Save and reboot the router. You will see the below bar

while the unit is restarting, when the unit is ready it will prompt you for the Web Interface login again.

The DVG-G1402S is now setup for the VoIP account. Your unit should now be connected to the Internet

and allow for you to make VoIP Phone Calls.

Andere Handbücher für DVG-G1402S - Wireless Broadband VoIP Router

Inhaltsverzeichnis

Andere D-Link WLAN-Router Handbücher

D-Link

D-Link DIR-615 - Wireless N Router Bedienungsanleitung

D-Link

D-Link DSL-2750E Bedienungsanleitung

D-Link

D-Link DWR-116 Bedienungsanleitung

D-Link

D-Link DWM-313 Bedienungsanleitung

D-Link

D-Link DIR-300A Bedienungsanleitung

D-Link

D-Link DIR-825/AC Bedienungsanleitung

D-Link

D-Link DWR-116 Bedienungsanleitung

D-Link

D-Link Ethernet Broadband Router DIR-100 Bedienungsanleitung

D-Link

D-Link DIR-620 Bedienungsanleitung

D-Link

D-Link DSL-2750U Bedienungsanleitung

D-Link

D-Link EXO AX DIR-X1870 Bedienungsanleitung

D-Link

D-Link DSL-2877AL Bedienungsanleitung

D-Link

D-Link DI-724P Bedienungsanleitung

D-Link

D-Link DAP-1350 Bedienungsanleitung

D-Link

D-Link DIR-636L Bedienungsanleitung

D-Link

D-Link DSL-2642B Bedienungsanleitung

D-Link

D-Link DWR-161 Bedienungsanleitung

D-Link

D-Link COVR-2202 Bedienungsanleitung

D-Link

D-Link DIR-619L Bedienungsanleitung

D-Link

D-Link DSL-3580L Series Bedienungsanleitung

D-Link

D-Link DIR-602 Bedienungsanleitung

D-Link

D-Link DIR-615 - Wireless N Router Bedienungsanleitung

D-Link

D-Link DIR-605L Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung

Sitecom

Sitecom WLR-4000 Bedienungsanleitung

BlueBOLT

BlueBOLT BB-ZB1 Bedienungsanleitung