Da-Lite Designer Da-Tab Electrol Bedienungsanleitung

INSTRUCTION BOOK FOR

Designer Da-Tab Electrol®

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of ire, electric shock, or

injury to persons.

Save These Instructions

Before proceeding with the installation of the screen, please read the installation and operations instructions thoroughly!

CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le papier d'emballage ou le ruban adhésif avec un couteau ou un outil tranchant.

Retirez à la main.

1. Carefully unpack the screen and remove the outer wrapping.

2. Always handle screen in upright position.

3. Remove the front cover of the screen from the back of the

screen. Lift front cover up approximately 1/2" and pull away

from back of screen. See Figure 1.

4. Remove hex head screws that secure the metal shipping

brackets to the wood board.

5. Remove the Phillips head screws that attach the screen

case to the wood board.

6. Remove the metal shipping brackets from the back

of the slat.

7. There are two methods of mounting the screen, suspended

from ceiling and wall mounted. See Figure 2.

NOTE: Allow 1/2" above screen (when mounted) for front

cover of screen installation and removal.

8. Picture surface is centered in case. Case extends 7" beyond

surface on either end. Do not attach anything to screen slat

on the bottom of the screen.

Pre-Installation

Picture

Surface

Ceiling Mounting

Place “D” Rings

Over Hooks

Well Secured

In Ceiling.

Figure 1

Hanger Bracket

Hanger

Front

Cover

Back

Screen

Picture

Surface

Slat

Picture

Surface

“V” Bar

Mounted

To The

Wall

Wall Mounting

Ceiling

Wall

“V” Bar

Mounted To

The Back Of

The Case At

The Factory

Figure 2

Allow A Minimum Of

1 ¼" From Ceiling

Designer Da-Tab Electrol®Installation

1. Hang screen from wall or ceiling.

For Wall Mounting

Hardware Provided

2 – “V” Bars ( one is factory mounted to the back

of the case; one will be mounted to the wall)

6 – Toggle Bolts, 4"

6 – Lead Shields, #1014 x 11⁄2"

6 – Phillips Flat Head Wood Screws, #10 x 2"

Tools Required

Electric Drill

Masonry Bit 5⁄16" (if mounting in solid masonry

or concrete)

Screw Driver, #2 Flat Tip (if using toggle bolts) or

#2 Phillips (if mounting in solid masonry or concrete)

Determine the height of the top of the case from the

loor. This will be the height of the wall mounted “V” bar.

Hold the loose “V” bar to the wall at the height

determined above (MAKE SURE IT IS LEVEL), and mark

the location for the screw holes. To mount the “V” bar on

solid concrete or masonry wall, drill 5⁄ 16" holes and insert

the lead shields. Fasten the “V” bar to the wall using the

#10 x 2" wood screws. If you are mounting to a hollow

wall, drill 1⁄2" holes and insert the toggle bolts. Then

fasten the “V” bar to the wall with the toggle bolts. Now

set the case in place on the wall with the “V” bar of the

case nestled into the “V” bar on the wall.

For Ceiling Mounting

Position and properly anchor screw hooks into ceiling, beam

or other solid surface. Then proceed to use the two “D” rings

that are factory mounted to the top of the case to hang the

case securely.

2. Install electrical hook-up that applies to your unit. Make

sure to review your electrical installation checklist and

wiring diagrams (included) for either 120 volt switch,

220/240 volt switch or low voltage control. See Figure 3.

3. Test installation by running screen up and down a few

times. Be prepared to stop screen. Standard Duty Cycle:

1 MIN. ON / 3 MIN. OFF.

NOTE: Must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code

(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70.

A = Fabric Width + 14"

B = Fabric Width

Picture

Surface

5 ½"

Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory. If it's necessary

to adjust for more or less drop follow the steps below. The case cover must be removed to access the motor limit switches.

Remove the front cover of the screen from the back of the screen. Lift front cover up approximately 1/2" and pull away from back of

screen. See Figure 1.

Setting The Down Limit Position

To Reduce Screen Drop:

Turn the white limit switch screw clockwise to decrease the

amount of screen drop. Run the screen down to test the stop

position. If the screen drops too far, raise the screen about

one foot and adjust the limit switch again. Repeat until the

desired position is set.

To Increase Screen Drop:

Turn the white limit switch screw counterclockwise to

increase the amount of screen drop. Run the screen down to

test the stop position. If the screen does not drop enough,

raise the screen about one foot and adjust the limit switch

again. Repeat until the desired position is set. Do not adjust

for more drop than what was ordered. At least 11/2 wraps of

fabric must remain on the roller.

Designer Da-Tab Electrol® Installation

Screen Adjustment For 120V And 220V/240V Screens

120V Wiring Diagram

Up Red Limit Switch Knob

In Multiple Control Installations

This Switch Is Replaced By The

Low Voltage Control, Operated

From Push Button Stations.

Operating Switch, Switch

Box, And Plate Furnished

With Screen. (SPDT With

Center Of)

This Switch Cannot Be Used With LVC.

NOTE: A single switch cannot be used to operate more than

one screen. Contact the factory for further information.

Black Down

Black

Red

Down

AC Hot

Of

White Common

Black With Yellow

Red Up

Rocker

Switch

AC Common

120 V. 50/60 Hz.

2.5 Amp. Max

Down White Limit

Switch Knob

Motor

External Wiring

To Be Completed

By Installer.

Side View

Of Switch

And Box

Figure 3

240 Volt Wiring Diagram For Standard Wall Switch:

Da-Lite ofers two styles of 240 volt wall switches for standard

operation. Please see wiring diagram included in wall switch box

included with screen.

To Junction Box, Mounted In Screen Case,

In Which Internal Wiring Terminates In White,

Black And Red Leads.

Troubleshooting

Visit www.da-lite.com to ind installation and troubleshooting

tutorials. You will also ind a link to Live Chat for interactive

support and you can contact us by email at info@da-lite.com or by

phone at (800) 6223737 or (574) 2678101 with any

troubleshooting questions.

Symptom Cause Solution

Screen will not operate

and motor does not hum.

Motor hums.

Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage,

rewire incoming electric line.

Blown fuse. Replace fuse.

Tripped circuit breaker. Reset circuit breaker.

No power to operating switch

or junction.

Check above. Tighten all loose wire connections.

Correct any improper connections.

Down Position

Check for power across black and white leads.

Up Position

Check for power across red and white leads.

Power at junction box

Thermal overload tripped.

Let motor cool down for 15 minutes. Try again.

Broken wire in the “down” or “up” position. Check for continuity. Cut o old splice and reconnect.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Temporary binding. With power “o”, turn roller by hand to free binding.

Capacitor burned out. Replace motor assembly.

Incorrect stopping position in

downward direction. “Down” limit switch out of adjustment. See installation instructions.

Incorrect stopping position in

upward direction. “Up” limit switch out of adjustment. Adjust “up” limit switch. Turn clockwise to expose more fabric.

See installation instructions

Noise.

NOTE: Screen will operate

with a low pitched hum.

Squeaking, rubber end plug rubbing on motor. Adjust roller to center of case.

Grinding. Foreign object in screen rubbing on roller

or fabric. Remove foreign object.

Gear noise. Replace motor assembly.

Coasting. Defective brake. Replace motor assembly.

Roller displaced from

mounting bracket. Pin end slipped out of nylon bearing. Remove pin end mounting.

Re-align motor in tube. Re-attach pin end.

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,

Warsaw, IN 465810137, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

75602

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0263 (Rev. 2) 09.14

Inhaltsverzeichnis

Andere Da-Lite Projektionsfläche Handbücher

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung

Da-Lite

Da-Lite ADVANTAGE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Theater-lite Bedienungsanleitung

Da-Lite

Da-Lite Ascender Electrol Bedienungsanleitung

Da-Lite

Da-Lite C with CSR Bedienungsanleitung

Da-Lite

Da-Lite senIor electrol Bedienungsanleitung

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED DUAL MASKING ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite advantage Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Contour Electrol Bedienungsanleitung

Da-Lite

Da-Lite VERSATOL Bedienungsanleitung

Da-Lite

Da-Lite ADVANTAGE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Tensioned Professional Electrol Bedienungsanleitung

Da-Lite

Da-Lite DESIGNER CONTOUR MANUAL Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite AdvantageManual With CSR Bedienungsanleitung

Da-Lite

Da-Lite DESIGNER MANUAL SCREEN Bedienungsanleitung

Da-Lite

Da-Lite Presenter P-50 Bedienungsanleitung

Da-Lite

Da-Lite Cosmopolitan Electrol Bedienungsanleitung

Da-Lite

Da-Lite DUAL MASKING ELECTROL Bedienungsanleitung

Da-Lite

Da-Lite Contour Electrol Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch