Da-Lite DESIGNER ELECTROL Bedienungsanleitung
ELECTROL
INSTRUCTION BOOK FOR
DESIGNER ELECTROL
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 219/267-8101
800-622-3737
Fax: 219/267-7804
http:// www.da-lite.com
e-mail: [email protected]
Before proceeding with the installation of the screen, please read the installation and operations instructions thoroughly!
CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by hand.
1. Carefully unpack the screen and remove the outer wrapping.
2. Always handle screen in upright position.
3. Remove the front cover of the screen from the back of the screen. Lift front cover up approximately 1/2" and pull
away from back of screen. See Figure 1.
4. There are two methods of mounting the screen: suspended from ceiling and wall mounted. See Figure 2.
NOTE: Allow 1/2" above screen (when mounted) for front cover of screen installation and removal.
5. Picture surface is centered in case. Case extends 5-1/2" beyond surface on either end. Do not attach anything to
screen slat on the bottom of the screen.
PRE-INSTALLATION
1
INSTALLATION
1. Hang screen from ceiling or wall. Make sure screen is level. Use a carpenter’s level and plum level.
2. Remove black tape from slat.
3. Install electrical hook-up that applies to your unit. Make sure to review your electrical installation checklist and
wiring diagrams (included) for either 120 volt switch, 220/240 volt switch or DRC low voltage control. See Figure 3.
NOTE: Screen must be wired to conform to local and national electrical codes.
▲
!
HANGER BRACKET
HANGER
PIN
FRONT
COVER
BACK OF
SCREEN
PICTURE
SURFACE
PICTURE
SURFACE
PICTURE SURFACE
SLAT
SLIP HANGER
EYES OVER
SCREWS WELL
SECURED IN
WALL.
WALL MOUNTING CEILING MOUNTING
PLACE “D”
RINGS OVER
HOOKS WELL
SECURED IN
CEILING.
FIGURE 1 FIGURE 2
2
The screen surface travel is stopped automatically in the fully opened and closed positions by limit switches that are
properly adjusted at the factory. The screen should not be adjusted for more or less drop.
Should the picture surface get out of adjustment and it be necessary to adjust picture surface drop, proceed in the follow-
ing manner.
NOTE: Use a small flat screwdriver or allen wrench to make adjustments. See Figure 3.
CAUTION! When adjusting limit switches and testing, be prepared to stop screen quickly as serious damage may
occur.
More Screen Drop
1. Place operating switch in
"
Down" position.
2. When the screen stops, turn the white "Down" limit knob one-quarter turn counter-clockwise. Test by raising picture
surface approximately two feet, then lower again. Repeat until proper screen drop has been attained.
Less Screen Drop
1. Raise picture surface approximately two feet above desired level.
2. Place operating switch in "Off" position.
3. Turn the white "Down" limit knob one-quarter turn clockwise. Test by lowering screen until it stops. Repeat until
proper screen drop has been attained.
NOTE: The yellow "Up" adjustment knob controls where fabric stops in the case. Do not adjust bottom slat to come
in contact with the fabric on roller.
Replace Front Cover
Center front cover on back of case, raise about 1/2" above the back, push front cover into cover hanger brackets and
lower into place.
SCREEN ADJUSTMENT
SCREEN ADJUSTMENT
▲
!
A
B
6"
5-1/2"
A = FABRIC WIDTH + 11"
B = FABRIC WIDTH
5-1/2" 5-1/2"
PICTURE
SURFACE
3
UP YELLOW LIMIT SWITCH KNOB
TO JUNCTION BOX MOUNTED IN
SCREEN CASE, IN WHICH INTERNAL
WIRING TERMINATES IN WHITE,
BLACK AND RED LEADS.
IN MULTIPLE CONTROL INSTALLATIONS
THIS SWITCH IS REPLACED BY THE LOW
VOLTAGE CONTROL, OPERATED FROM
PUSH BUTTON STATIONS. SEE DIAGRAM
Nos. 46967 AND 74425, AVAILABLE UPON
REQUEST.
OPERATING SWITCH, SWITCH
BOX, AND PLATE FURNISHED
WITH SCREEN. (SPDT WITH
CENTER OFF)
THIS SWITCH CANNOT BE USED WITH LVC.
NOTE: A single switch cannot be used to operate more than
one screen. Contact the factory for further information.
BLACK DOWN
BLACK
UP
RED
DOWN
AC HOT
OFF
WHITE COMMON
BLACK WITH YELLOW
RED UP
ROCKER
SWITCH
AC COMMON
120 VOLTS
50/60 HZ.
2.5 MAX. AMP.
DOWN WHITE LIMIT SWITCH KNOB
MOTOR
EXTERNAL WIRING
TO BE COMPLETED
BY INSTALLER.
SIDE VIEW
OF SWITCH
AND BOX
FIGURE 3
DESIGNER ELECTROL INSTALLATION
220 / 240V
WIRING DIAGRAM
UP YELLOW LIMIT SWITCH KNOB
TO JUNCTION BOX, MOUNTED IN
SCREEN CASE, IN WHICH INTERNAL
WIRING TERMINATES IN BLUE,
BROWN AND BLACK LEADS.
NOTE: MUST BE WIRED TO CONFORM TO
LOCAL WIRING CODE. THIS SWITCH
CANNOT BE USED WITH L.V.C.
OPERATING SWITCH, SWITCH
BOX, AND PLATE FURNISHED
WITH SCREEN.
THIS SWITCH CANNOT BE USED WITH LVC.
NOTE: A single switch cannot be used to operate more than
one screen. Contact the factory for further information.
DOWN WHITE LIMIT SWITCH KNOB
MOTOR
FIGURE 3
BLACK (UP)
UP
DOWN
OFF
BLUE (COMMON)
BROWN /
YELLOW
ROCKER
SWITCH
220 /240V. AC 50HZ.
2 AMP. MAX.
BROWN (DOWN)
BLUE JUMPER WIRE
BLUE AC COMMON
BROWN AC HOT
JUNCTION
BOX
IN MULTIPLE CONTROL INSTALLATIONS
THIS SWITCH IS REPLACED BY THE LOW
VOLTAGE CONTROL, OPERATED FROM
PUSH BUTTON STATIONS.
EXTERNAL WIRING
TO BE COMPLETED
BY INSTALLER.
REAR VIEW OF DPDT,
WITH CENTER OFF.
120V
WIRING DIAGRAM
TROUBLESHOOTING
SYMPTOM
1. Screen will not operate or will
not go “down”.
Motor does not hum.
Motor hums.
2. Screen will not move “up”.
Motor does not hum.
Motor hums.
3. Incorrect stopping position in
downward direction.
4. Incorrect stopping position in
upward direction.
5. Noise
NOTE: Screen will operate with a
low pitched hum.
6. Coasting.
7. Roller displaced from mounting
bracket.
CAUSE
(a) Blown fuse.
(b) Tripped power supply circuit breaker.
(c) No power to operating switch or
junction.
Power at junction box.
(d) Thermal overload tripped.
(e) Broken wire in the "down" position.
(f) Defective motor.
(g) Temporary binding.
(h) Motor burned out.
(a) Blown fuse.
(b) Tripped power supply circuit breaker.
(c) No power to operating switch or
junction.
Power at junction box.
(d) Thermal overload tripped.
(e) Broken wire in the "up" position.
(f) Defective motor.
(g) Temporary binding.
(h) Motor burned out.
(a) "Down" limit switch out of adjust-
ment.
(a) "Up" limit switch out of adjustment.
(a) Squeaking rubber end plug on
motor.
(b) Grinding due to foreign object in
screen rubbing on roller or fabric.
(c) Gear noise.
(a) Defective brake.
(a) Pin end slipped out of nylon bearing.
SOLUTION
(a) Replace fuse.
(b) Reset circuit breaker.
(c) Check above. Tighten all loose wire
connections. Correct any improper
connections.
“Down” Position
Check for power across black and
white leads.
(d) Let motor cool down for 15 minutes.
Try again.
(e) Check for continuity. Cut off old
splice and reconnect.
(f) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(g) With power OFF, turn roller by hand
to free binding.
(h) Replace motor assembly.
(a) Replace fuse.
(b) Reset circuit breaker.
(c) Check above. Tighten all loose wire
connections. Correct any improper
connections.
“Up” Position
Check for power across red and
white leads.
(d) Let motor cool down for 15 minutes.
Try again.
(e) Check for continuity. Cut off old
splice and reconnect.
(f) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(g) With power off, turn roller by hand to
free binding.
(h) Replace motor assembly.
(a) See installation instructions.
(a) Adjust "up" limit switch. Turn clock-
wise to expose more fabric. See in-
stallation instructions.
(a) Adjust roller to center of case.
(b) Remove foreign object.
(c) Replace motor assembly.
(a) Replace motor assembly.
(a) Remove pin end mounting. Realign
motor in tube. Re-attach pin end.
4
Printed in U.S.A. 76401 Rev. 1/98
LIMITED ONE YEAR WARRANTY ON DA-LITE PROJECTION SCREENS
Da-Lite Screen Company, Inc. warrants its screens to the original purchaser only, to be free from defects in materials
and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided they are prop-
erly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after ship-
ment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage, or which has
been tampered with or repaired by person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the
merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the
screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not
responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the product and prepay
all transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS
TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of fitness for use, or merchantability, that may
be mandated by statue or rule of law are limited to the one (1) year warranty period. This warranty gives you specific
legal rights, and you may also have other rights which vary from state-to-state. NO LIABILITY IS ASSUMED FOR
EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL,
DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite Screen, you may contact our Customer
Service Department at P.O. Box 137, Warsaw, Indiana 46581-0137 (219/267-8101) Toll Free (800/622-3737).
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE BOUND BY THIS WAR-
RANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA-LITE’S WRITTEN
INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
5
Inhaltsverzeichnis
Andere Da-Lite Projektionsfläche Handbücher
Da-Lite
Da-Lite Advantage Manual With CSR Bedienungsanleitung
Da-Lite
Da-Lite Contour Electrol Bedienungsanleitung
Da-Lite
Da-Lite Theater-Lite Bedienungsanleitung
Da-Lite
Da-Lite VERSATOL Bedienungsanleitung
Da-Lite
Da-Lite Cosmopolitan Electrol Bedienungsanleitung
Da-Lite
Da-Lite ADVANTAGE ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite DESIGNER DA-TAB ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Cosmopolitan Electrol Bedienungsanleitung
Da-Lite
Da-Lite Wireline Advantage Bedienungsanleitung
Da-Lite
Da-Lite Tensioned Advantage Deluxe Electrol Bedienungsanleitung
Da-Lite
Da-Lite TILT-LOCK Handbuch
Da-Lite
Da-Lite Large Cosmopolitan Electrol Bedienungsanleitung
Da-Lite
Da-Lite PROFESSIONAL ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Model C With CSR Bedienungsanleitung
Da-Lite
Da-Lite Model B Bedienungsanleitung
Da-Lite
Da-Lite IMAGER Bedienungsanleitung
Da-Lite
Da-Lite Parallax Bedienungsanleitung
Da-Lite
Da-Lite Tensioned Conference Electrol Bedienungsanleitung
Da-Lite
Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Bedienungsanleitung
Da-Lite
Da-Lite Model C Bedienungsanleitung
