Daikin FTE09MV2S Bedienungsanleitung
REMOVAL
PROCEDURE
SERVICE MANUAL
Indoor Unit
Non-Inverter
Wall Mounted Type
9000/12000 Btu/h Class
Si041138
Service Manual
Removal Procedure
Indoor Unit
Applicable Models
zCooling Only
FTE09MV2S
FTE12MV2S
Si041138
Removal Procedure 1
Table of Contents
1. Removal of Air Filters..............................................................................2
2. Removal of Front Panel ..........................................................................4
3. Removal of Front Grille ...........................................................................5
4. Removal of Horizontal Blades / Vertical Blades......................................8
5. Removal of Electrical Box .....................................................................11
6. Removal of PCBs..................................................................................14
7. Removal of Drain Pan Unit / Swing Motor.............................................19
8. Removal of Fan Motor...........................................................................23
9. Removal of Indoor Heat Exchanger......................................................25
10.Removal of Fan Rotor ...........................................................................28
Note: The illustrations may be slightly different depending on the model.
Removal of Air Filters Si041138
2Removal Procedure
1. Removal of Air Filters
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1. Appearance features
Warning
Dangerous: High voltage
A high voltage is applied to all
the electric circuits of this
product including
thermistors.
When the signal receiver
catches a signal from the
remote controller, the
receiving tone sounds and
the operation lamp blinks
immediately to confirm the
signal reception.
When the [ON/OFF] button
is kept pressed for 5
seconds, the forced cooling
operation is performed for
about 15 minutes.
2. Remove the air filters.
1
2
3
Open the front panel to
the position where it
stops.
Slightly push up the
center knob of the air
filter and unfasten the
hooks.
Pull out the air filter
downward and remove
it.
The air filter is not marked
for difference between the
right and left sides.
Insert the air filter with the
"FRONT" mark faced up.
The air filter can be set
easily by inserting it along
the guides.
Be sure to insert the hooks
(at 2 lower positions) when
mounting the air filter.
(R12544)
(R15463)
[ON/OFF] button
Operation lamp
TIMER lamp
Signal receiver
Room temperature
thermistor
(R4846)
Front panel
(R4847)
Air filter
Si041138 Removal of Air Filters
Removal Procedure 3
3. Remove the Titanium
apatite photocatalytic air-
purifying filters.
1The Titanium apatite
photocatalytic air-
purifying filter ASSY is
attached to the back of
the air filter.
The right and left filters are
interchangeable.
2
3
Remove the Titanium
apatite photocatalytic
air-purifying filter ASSY
by bending the air filter
and releasing the
projections from the air
filter frame.
Remove the Titanium
apatite photocatalytic
air-purifying filter from
its frame (at 5 positions)
by bending it.
Step Procedure Points
Air filter
(R4309)
Titanium apatite
photocatalytic
air-purifying filter
ASSY
Projection
(R4310)
(R13174)
Removal of Front Panel Si041138
4Removal Procedure
2. Removal of Front Panel
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1Open the front panel
over the position where
it stops.
2Slide the left rotary
shaft to the right and
release it.
3
4
Slide the right rotary
shaft to the left and
release it.
Remove the front panel.
When reassembling the front
panel, fit the right and left
rotary shafts one by one into
the grooves and fully push
them in position.
(R4849)
Rotary shaft
Rotary shaft
(R4313)
(R4315)
Front panel
(R4850)
Si041138 Removal of Front Grille
Removal Procedure 5
3. Removal of Front Grille
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1. Remove the service
cover.
Preparation
Remove the front panel
according to the “Removal of
Front Panel.”
1Remove the screw of
the service cover.
2
3
Pull out the service
cover diagonally down
in the direction of the
arrow.
The figure shows the
inside.
You can remove the front
grille without detaching the
service cover.
2. Remove the front grille.
1Open the horizontal
blades.
(R4851)
Service cover
(R4852)
(R4853)
(R4854)
Horizontal blade
Removal of Front Grille Si041138
6Removal Procedure
2
3
4
5
Remove the screw
covers. (right and left)
Remove the 2 screws.
(right and left)
The front grille has 3
hooks at the top.
Unfasten the left hook.
When mounting the indoor
unit, drive the screws with
the horizontal blades open or
removed.
The convex marks (...) on
the front panel indicate the
position of the hooks.
Step Procedure Points
Hook
(R4321)
(R12769)
(R4324)
Screw cover
(R4855)
Front grille (R12715)
Si041138 Removal of Front Grille
Removal Procedure 7
6
7
8
Unfasten the center
hook.
Unfasten the right hook.
Pull the upper part of
the front grille out and
lift the lower part up,
and then remove the
front grille.
When reassembling the front
grille, make sure that the 3
hooks are fastened as they
were.
When reassembling the front
grille, be sure not to get it
stuck on the spacer of the
drain pan.
Step Procedure Points
(R4325)
(R4326)
(R12545)
Spacer
(R4856)
Front grille
Spacer
Section View
(R4590)
Removal of Horizontal Blades / Vertical Blades Si041138
8Removal Procedure
4. Removal of Horizontal Blades / Vertical Blades
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1. Remove the horizontal
blade (large).
1
2
3
4
Open the horizontal
blade (large).
Unfasten the center
shaft while bending the
horizontal blade (large)
slightly.
Unfasten the left shaft.
Unfasten the right shaft.
Mount the large horizontal
blade to the upper position
and the small horizontal
blade to the lower position.
Do not put them in the wrong
place.
There is a key alignment at
the right shaft. When
mounting, insert the right
shaft first while turning.
After inserting the right shaft,
mount the horizontal blade to
the center shaft and then to
the left shaft.
(R4857)
Horizontal blade (large)
Horizontal blade (small)
(R4329)
(R4330)
Key alignment
(R12734)
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Daikin Klimaanlage Handbücher
Daikin
Daikin DCM601A51 Bedienungsanleitung
Daikin
Daikin Sky Air Alpha Series Anleitung zur Verwendung
Daikin
Daikin CTKS25TVMG Bedienungsanleitung
Daikin
Daikin B-Series Bedienungsanleitung
Daikin
Daikin RoofPak RPS Series Handbuch
Daikin
Daikin ARKC18RV2S Bedienungsanleitung
Daikin
Daikin FTXM42K3V1B Bedienungsanleitung
Daikin
Daikin R-410A Bedienungsanleitung
Daikin
Daikin 2MXU40GV1B Bedienungsanleitung
Daikin
Daikin FTXP60N2V1B Produktinformationsblatt
Daikin
Daikin FXSQ-P7VEB Gebrauchsanweisung
Daikin
Daikin RXS71FAV1B8 Bedienungsanleitung
Daikin
Daikin FXSN20AV1 Bedienungsanleitung
Daikin
Daikin SkyAir RZQ18PVJU Bedienungsanleitung
Daikin
Daikin Altherma EHVZ04S18DA6V Bedienungsanleitung
Daikin
Daikin FTKS20DVMW(L) Bedienungsanleitung
Daikin
Daikin FXDQ20P3VE Bedienungsanleitung
Daikin
Daikin Altherma 3 R ECH2O Produktinformationsblatt
Daikin
Daikin Altherma EABH16DA6V Bedienungsanleitung
Daikin
Daikin VRVIII-S Series Gebrauchsanweisung
