Daikin BRC7E530W Bedienungsanleitung

1English

BRC7E530W

BRC7E531W Wireless Remote Controller Kit Installation manual

CONTENTS

1. SAFETY CONSIDERATIONS ........................................................................................1

2. BEFORE INSTALLATION ..............................................................................................2

3. REMOTE CONTROLLER INSTALLATION ....................................................................2

4. RECEIVER INSTALLATION...........................................................................................3

5. FIELD SETTING.............................................................................................................6

6. TEST OPERATION ........................................................................................................8

1. SAFETY CONSIDERATIONS

Please read this “SAFETY CONSIDERATIONS” carefully before installing air conditioning equipment and be

sure to install it correctly. After completing the installation, make sure at start up operation that the unit oper-

ates properly. Please instruct the customer how to operate the unit and keep maintenance.

Meaning of caution symbols

CAUTION .............. If the caution is not observed, it may cause injury or damage to equipment.

NOTE ............. These instructions will ensure proper use of the equipment.

CAUTION

•Refer also to the installation manual attached to the indoor unit and the installation manual attached to the

decoration panel.

•Confirm that following conditions are satisfied prior to installation.

•Ensure that nothing interrupts the operation of the wireless remote controller. (Ensure that there is nei-

ther a source of light nor fluorescent lamp near the receiver. Also, ensure that the receiver is not

exposed of direct sunlight.)

•Ensure that the operation display lamp and other indicators are easy to see.

•The installation position of this kit is 1 position of the decoration panel. Therefore, confirm that its position

is set so that the single form the wireless remote controller can be easily transmitted and its display can be

easily seen.

English 2

2. BEFORE INSTALLATION

2-1 ACCESSORIES

Check if the following accessories are included with your unit.

2-2 NOTE TO THE INSTALLER

•Be sure to instruct the customer how to properly operate the system showing him/her the attached opera-

tion manual.

3. REMOTE CONTROLLER INSTALLATION

〈Installing wireless remote controller〉

•Do not throw the remote controller or impose large shocks. Also, do not store where it may be exposed to

moisture or direct sunlight.

•When operating, point the transmitting part of the remote controller in the direction of the receiver.

•The direct transmitting distance of the remote controller is approximately 7 meters.

•The signal cannot be transmitted if something such as curtains blocks the receiver and the remote control-

ler.

• Installing to a wall or a pillar

(1) Fix the remote controller holder with the screws.

(2) Slide the remote controller into the remote controller holder

from the top.

Name Receiver Transmitter board Tapping screw for

transmitter board

Wireless remote

controller

Remote controller

holder

Quan-

tity 1 set. 1 pc. 2 pcs. 1 pc. 1 pc.

Shape

Name Dry cell battery

LR03 (AM4)

Unit No.

label

Screw for install-

ing remote control-

ler holder

Operation manual Clamp

Quan-

tity 2 pcs. 1 pc. 2 pcs. 1 pc. 1 pc.

Shape 123

123

(1)

(2)

3English

• How to insert the batteries

1. Open the back cover of the remote controller by sliding it in the

direction of the arrow.

2. Insert the attached dry cell batteries. Properly insert, set the

batteries by matching the (+) and (–) polarity marks as indi-

cated. Then close the cover as before.

4. RECEIVER INSTALLATION

(1) Preparations before installation

1. Detach the brand name plate part of

the decoration corner panel piece,

before attaching the decoration panel.

This part is not needed hereafter.

2. Next, remove the suction grille and the

air filter according to the instructions in

the installation manual attached to the

decoration panel.

3. Remove the control box lid according

to the instructions in the installation

manual attached to the indoor unit.

(Be sure to turn off power, before

removing the control box lid.)

(2) Determination of address and MAIN/

SUB remote controller.

If setting multiple wireless remote control-

lers to operate in one room, perform

address setting for the receiver and the

wireless remote controller.

If setting multiple wired remote controllers

in one room, change the MAIN/SUB switch of the receiver.

SETTING PROCEDURE

1. Setting the receiver

Set the wireless address switch (SS2) on the transmitter board accord-

ing to the table below.

When using both a wired and a wireless remote controller for 1 indoor

unit, the wired controller should be set to MAIN. Therefore, set the MAIN/

SUB switch (SS1) of the transmitter board to SUB.

Unit No. No. 1 No. 2 No. 3

Wireless address

switch (SS2)

MAIN SUB

MAIN/SUB

switch (SS1)

Decoration panel

Brand name plate part

Push three hooks

to detach them

from the holes of

the rear side.

123 MS

SS2 SS1

1 2 3

English 4

2. Setting the address of wireless remote controller (It is factory set to “ 1 ” )

〈Setting from the remote controller〉

1. Hold down the button and the button for at

least 4 seconds to get the Field Set mode.

(Indicated in the display area in the figure at right.)

2. Press the button and select a multiple setting (A/

b). Each time the button is pressed the display switches

between “A” and “b”.

3. Press the “ ” button and “ ” button to set the

address.

Address can be set from 1 to 6, but set it to 1 ~ 3 and to

same address as the receiver. (The receiver does not work

with address 4 ~ 6.)

4. Press the button to enter the setting.

5. Hold down the button for at least 1 second to quit

the Field Set mode and return to the normal display.

Multiple settings A/b

When the indoor unit is being operating by outside control (central remote controller, etc.), it sometimes does

not respond to ON/OFF and temperature setting commands from this remote controller. Check what setting

the customer wants and make the multiple setting as shown below.

3. Stick the Unit No. label on the air outlet of the

decoration panel and the back of the wireless

remote controller.

[PRECAUTIONS]

Set the Unit No. of the receiver and the wireless

remote controller to be equal. If the settings differ,

the signal from the remote controller cannot be

transmitted.

Remote controller Movement when the operation is controlled by the

other air conditioners and equipment

Multiple setting Remote controller display

A: Standard All items displayed.

When operation changeover, temperature setting or

the like is carried out from the remote controller, the

indoor unit rejects the instruction.

(Signal receiving sound “peeh” or “pick-pick-pick”)

As a result, a discrepancy between the operation

state of the indoor unit and the indication of the

remote controller display occurs.

b: Multi System

Operations remain dis-

played shortly after exe-

cution.

Since the indication of the remote controller is turned

off, no discrepancy such as mentioned above occurs.

MODE

TIMER

RESERVE

CANCEL

DOWN

/TEST

SWING

FAN

TIME

TEMP

ON OFF

SETTING

Mode

Address

Multiple setting

/TEST

FAN

UP DOWN

12345 6

RESERVE

/TEST

Unit No. label

Wireless remote controller

Decoration

panel

5English

(3) Receiver installation

1. As shown at right, pass the harness from the receiver through the

wiring hole of the decoration panel. Then, attach the receiver to

the decoration panel.

2. Hook the harness from the receiver on the upper part of the

panel temporary suspension of the decoration panel.

Be sure to push the harness to the groove.

3. Attach the decoration panel to the indoor unit.

(Refer to the installation manual attached to the decoration panel.)

4. Connect the harness from the receiver to the connector X1A on the transmitter board.

After connecting, use the attached clamp to fix the two harnesses to the transmitter board box.

Panel temporary suspension

X2A X1A

Clamp

X2A X1A

English 6

5. Use two tapping screws to attach the transmitter board to

the indoor unit, as shown in the figure.

6. Connect the harness from the transmitter board to the connector X24 on the indoor unit PC board.

5. FIELD SETTING

If optional accessories are mounted on the indoor unit, the indoor

unit setting may have to be changed. Refer to the instruction man-

ual (optional hand book) for each optional accessory.

Procedure

1. When in the normal mode, press the button for a min-

imum of four seconds, and the FIELD SET MODE is entered.

2. Select the desired MODE NO. with the button.

3. Push the “”button and select the FIRST CODE NO.

4. Push the “”button and select the SECOND CODE NO.

5. Push the button and the present settings are SET.

6. Push the button to return to the NORMAL MODE.

Position of the

connector in the case

of the VRV system.

Be sure to wire the harness

as shown to avoid the harness

to be caught by the control box

and the control box lid. X24

Be sure to pass only the harness

connecting to the indoor unit PC

board under the tab.

DOWN

FAN

MODE

TIMER

RESERVE

CANCEL

/TEST

SWING

ON OFF

SETTING

TIME

TEMP

MODE NO.

1, 6

FIELD SET MODE

FIRST CODE NO.

SECOND CODE NO.

/TEST

MODE

DOWN

RESERVE

/TEST

7English

(Example)

If the time to clean air filter is set to “Filter Contamination-Heavy”, set Mode No. to “10”, FIRST CODE NO. to

“0”, and SECOND CODE NO. to “02”.

NOTE

•The SECOND CODE NO. is factory set to “01”. However, for the following cases it is set to “02”.

•Air Flow Direction Range Setting

Do not use any settings not listed in the table.

For group control with a wireless remote controller, initial settings for all the indoor units of the group are equal.

(For group control, refer to the installation manual attached to the indoor unit for group control.)

MODE

NO.

FIRST

CODE

NO.

DESCRIPTION OF SETTING

SECOND CODE NO. NOTE)

01 02 03

Filter Contamination-

Heavy/Light (Setting

for spacing time of dis-

play time to clean air

filter) (Setting for when

filter contamination is

heavy, and spacing

time of display time to

clean air filter is to be

halved)

Long-life

type light

approx.

2,500

hours

heavy

approx.

1,250

hours

Spacing time of display time to

clean air filter count

(Setting for when the filter sign is

not to be displayed)

Display Do not display -

(VRV

system)

ON/OFF input from outside (Set to

enable starting/stopping from

remote.)

Forced OFF input ON/OFF -

Thermostat differential changeover

(Set when using remote controller

thermostat sensor.)

1°C 0.5°C -

13 1

Selection of Air Flow Direction (Set-

ting for when a sealing member of

air discharge outlet kit has been

installed)

FTW

4 Air Flow Direction Range Setting Upper Normal Lower

English 8

6. TEST OPERATION

•Perform test operation according to the instructions in the installation manual attached to the indoor unit.

•After refrigerant piping, drain piping, and electric wiring, operate according to the table to protect the unit.

[PRECAUTIONS]

1. Refer to malfunction code of installation manual attached to the indoor unit, if it does not operate.

2. Refer to the installation manual attached to the outdoor unit for individual operation system types.

Order Operation

(1) Open gas side stop valve.

(2) Open liquid side stop valve.

(3) Electrify for 6 hours.

(4) Set to cooling with the remote controller and push button to start operation.

(5) Push button twice and operate in TEST OPERATION mode for 3 minutes.

(6) Push button and confirm its operation.

(7) Push button and operate normally.

(8) Confirm its function according to the operation manual.

ON/OFF

/TEST

SWING

/TEST

Andere Handbücher für BRC7E530W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Daikin Controller Handbücher

Daikin

Daikin MicroTech III Bedienungsanleitung

Daikin

Daikin BRC1H61W Systemhandbuch

Daikin

Daikin Maverick I Bedienungsanleitung

Daikin

Daikin MicroTech III Handbuch

Daikin

Daikin DCS601B51 Bedienungsanleitung

Daikin

Daikin MicroTech I Bedienungsanleitung

Daikin

Daikin BACnet Handbuch

Daikin

Daikin IM 735-4 Handbuch

Daikin

Daikin MD5 Bedienungsanleitung

Daikin

Daikin Altherma EKWHCTRL1 Leitfaden

Daikin

Daikin SLM Bedienungsanleitung

Daikin

Daikin BRC7C64W Bedienungsanleitung

Daikin

Daikin RoCon+ HP Bedienungsanleitung

Daikin

Daikin ARC447A3 Gebrauchsanweisung

Daikin

Daikin ECFWEB6 Bedienungsanleitung

Daikin

Daikin System Manager Bedienungs- und Wartungsanleitung

Daikin

Daikin FWECSA Bedienungsanleitung

Daikin

Daikin UATYP-AY1(B) Bedienungsanleitung

Daikin

Daikin ALTHERMA Bedienungsanleitung

Daikin

Daikin QUG-Altherma Interface Gebrauchsanweisung

Daikin

Daikin DKN-MP130-24MP Bedienungsanleitung

Daikin

Daikin MicroTech III Installationshandbuch

Daikin

Daikin BRC1H62W Bedienungsanleitung

Daikin

Daikin ACS320 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch