Daintree GE current WWS3 Bedienungsanleitung

(WWS3)

Daintree®Wireless

3-Button Wall Switch

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save these instructions for future use.

1Installation Process

2Packing List

Installation Guide

WWS3 |DT101

The Daintree WWS3 Wireless Wall Switch operates seamlessly

within the Daintree Networked wireless lighting control system.

Using wireless communications, this switch can be used to turn

lights On or Off, as well as half brightness. Installation is quick

and easy without any wires.

Features

• Suitable for many applications, including commercial

  ofce,retail,educationandwarehouse

• Simple wall mount

• Completely wireless installation

Each WWD1 dimmer package includes these items:

• Dimmer base

• Dimmer wall plate cover

• Two AAA 1.5V batteries

• Two mounting screws

1. Determine the mounting location

for the dimmer.

2. Locate the IEEE address on the

back of the dimmer base.

Record the dimmer’s IEEE address

and location on the facility

 oorplan.

3. Remove the cover from the base

(as shown on reverse of this page).

4.Attachthemountingbasetothewallinthespeciedlocation

using two screws. The Network LED should be at the upper left

side of the unit.

5. Install the batteries in the orientation (+ - ) shown on the

bottom of the battery compartments.

6. Press and hold the Utility button for 5 seconds. The Network

 LEDbeginstoashrapidlywhilethedimmerattempts

to join the ZigBee network. See the Green LED: Daintree

Networked Indicator Operation table. When the LED turns

on solid for 10 seconds, the dimmer has successfully joined

the network.

7. Align the round hole in the dimmer cover with the Network

LED on the base. Snap the cover onto the base.

Risk of electrical shock. Disconnect power before servicing or

installing product.

Install in accordance with National Electric Code and local codes.

WARNING

Risk of injury. Wear safety glasses and gloves during installation and

servicing.

CAUTION

IEEE Address

Label

Utility Button

Network

LED

Base

Half Brightness

Off

Network LED

Cover

Installation GuideDaintree®Wireless 3-Button Wall Switch (WWS3)

Joining the Lighting Control Network

LED Operation

Rapid ash (12 times

per second) for up to

30 seconds

Solid for 10 seconds

Flashes twice

On for 2 seconds every

30 seconds

Device is trying to join ZigBee

network. If it fails to join, it will retry

after 15 minutes.

Device successfully joined a ZigBee

network.

Device has been activated

while in the network.

A low battery alert will be generated

in CSM

Green LED:

Network Indicator

Description

The WWS3 communicates using a ZigBee® mesh network

coordinated by a Daintree Wireless Area Controller (WAC)

to effect lighting control in the Daintree Networked system.

Formoreinformationaboutconguringthelightingcontrol

network, see the instructions and on-line help provided with

the Daintree Controls Software web application.

Turn on lights

Half brightness

Turn off lights

Press the top button.

Press and hold the middle.

Press the bottom button.

Function

Dimmer Paddle

Note: Dimming from the highest level to the lowest level takes about 4 seconds.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encourage to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;

• Increase the separation between the equipment

and receiver;

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected;

• Consult the dealer or an experienced radio/TV

technician for help.

5FCC Warning Message

Power Supply Two AAA 1.5V batteries

Battery Life: 5 years

Operating DC 2.3V-3.6V

Voltage

Radio Properties 2.4 GHz, +7dBm transmit power

FCC ID (USA) NRH-ZB-Z100B

IC (Canada) 8984A-Z100B

ICES/NMB-003 CLASS B

Operating Indoor, dry location.

Environment 14° to 122° F (-10° to 50° C)

Storage -40° to 185° F (-40° to 85° C)

Temperature

Mounting Wall; 2 screws

Dimensions 2.76” W x 4.49” H x 0.59” D

(70mm W x 114mm H x 15mm D)

Specications

Product complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

6Industry Canada (IC) Warning Message

Installation GuideDaintree®Wireless 3-Button Wall Switch (WWS3)

Maintenance

Clean the dimmer cover only using a damp cloth and mild

detergent if necessary. Use of harsh chemicals or solvents

could cause permanent damage.

Changing the batteries

The LED indicator light turns On for 2 seconds every 30 seconds

to indicate a low battery condition. Replace the batteries

immediately upon noticing this condition. Under normal use,

the batteries can last up to 5 years.

1. To remove cover:

A. Graspthelongedgesofthecoverwithtwongers

from each hand on one side, and the thumbs of

   bothhandsontheotherside.Usetheindexnger

   ofbothhandstopressdownrmlyonbothendsof

the paddle. Squeeze and lift the long edges of the

cover as you push down on the paddle. The cover

will pop off the base.

-or-

B. Insert a wide blade screwdriver in either the top or

bottom notch in the base of the cover. Press down

   rmlyonthepaddlethentwistthescrewdriverto

loosen the cover. Insert the screwdriver in the notch

on the opposite edge of the cover then twist to pop

off the cover.

3. Remove both old batteries and discard properly. Do not

mix old and new batteries, or batteries from different

manufacturers.

4. Install two new AAA 1.5V batteries. Observe the orientation

(+ -) shown on the bottom of the battery compartments.

5. After replacing the batteries, press the Utility button for two

  seconds.TheNetworkLEDshouldashtwice.

6. Align the round hole in the dimmer cover with the Network

LED on the base. Snap the cover onto the base.

Questions:

Web: products.gecurrent.com

Phone: 1-866-855-8629

CAUTION

RISK OF EXPOSURE IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. DISPOSAL OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS.

WWS3

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation

ormaintenance.Shouldfurtherinformationbedesiredorshouldparticularproblemsarisewhicharenotcoveredsufcientlyforthepurchaser’spurposes,themattershouldbe

referred to GE Current, a Daintree company.

www.gecurrent.com