Dakota Alert AD-01 Kit Bedienungsanleitung

AD-01 Slave

Auto Dialer

Owner’s Manual

AD-01 Slave Manual.indd 1 10/15/2009 10:20:44 AM

2 3

AD-01 Slave Manual.indd 2 10/15/2009 10:20:44 AM

2 3

Features:

Programmable entry/exit delay time; select up to 9 (32 digit) user programmable phone numbers

for each alarm; dierent 10 second recordable message for each alarm; built-in tamper switch;

built-in terminal block for alarm and siren connection; DC adaptor with battery back-up; pro-

grammable as silent alarm (dialer only) or audible (siren + dialer).

Contents:

1 - Auto Dialer

1 - 12V DC Adaptor

1 - Installation & Programming Guide

1 - Telephone Cable

1 - Back-up Battery

AD-01 Slave Manual.indd 3 10/15/2009 10:20:44 AM

4 5

Installation

Tools needed: Small Phillips Screwdriver;

Large Phillips Screwdriver; Small Standard

Screwdriver.

Set Up:

1. Install the back-up battery (included) into the auto

dialer. Use a small Phillips screwdriver to remove screw

above battery cover (Figure 1-2). Remove cover by

sliding downwards. Plug in battery pack making sure

not to force onto pins incorrectly. Put battery pack in

space provided, close battery cover, and replace the

screw.

3. Connect the power supply to the dialer by inserting

the red wire into the 12V+ terminal and the black wire into the OV terminal (Figure 2). Using a

small standard screwdriver, turn the screws on the terminal to secure the wires.

4. The dialer can support two alarm trigger inputs (normally open) plus a tamper alarm output

(normally closed).

Figure 1

1 4 5 3 2

AD-01 Slave Manual.indd 4 10/15/2009 10:20:44 AM

4 5

TAMPER ALARM: The tamper alarm is alarmed

when the button on the back of the dialer

(Figure 1-3) is depressed. If the tamper output is

to be used it is important to be sure the button is

depressed when the unit is mounted.The tamper

terminals can be connected to any existing

security system or alarm that accepts a normally

closed input trigger. If the tamper output is not

connected to any system, the jumper wire must

remain between these terminals.

TR1/TR2: Triggers 1 and 2 support sensors with

normally open outputs. For Trigger 1, the sensor

wires would be connected to the TR1 terminal

and the OV terminal (Figure 2). For Trigger 2,

the sensor wires would be connected to the TR2 terminal and the OV terminal. (Note: Since these

terminals are simply “switches” there is no positive or negative. The wires can be hooked up either

way.)

5. Plug the supplied phone cord into the “LINE” jack (Figure 1-4) and then into your home phone

jack. If you wish to connect a phone at the dialer location, you can connect the phone to the

“PHONE” jack (Figure 1-5) on the dialer.

6. Continue on to the Advanced Operations to program your dialer or refer to the “AD-01 Quick

Reference Programming” on page 14.

TAMP TR2 TR1 OV 12V+

Trig 2

Trig 1 12V

OV = Universal Ground

Figure 2 (from Figure 1-1)

AD-01 Slave Manual.indd 5 10/15/2009 10:20:44 AM

6 7

Advanced Operations

HOW TO PROGRAM THE AUTO DIALER

*If no key is pressed for 30 seconds, the dialer will automatically exit the programming mode.

Notice: The system must be in the OFF mode for all programming.

How to record the voice messages:

Alarm 1 = Trigger 1. Alarm 2 = Trigger 2.

1. Key in the four digit user password code (factory default is 1234.)

2. Press RECORD.

3. Press 1(to save as the message for alarm 1) or 2(to save as the message for alarm 2).

4. Press ENTER to start recording your 10 second message.

5. Press ENTER to stop the recording early or wait for the 10 seconds to end.

Quick guide: Press 1 2 3 4 > RECORD > 1> ENTER, record message now

How to play back the message:

Press 1 2 3 4 > PLAY > 1> ENTER to play back the recorded message.

(Notice: 1= the rst message, 2= the second message).

AD-01 Slave Manual.indd 6 10/15/2009 10:20:44 AM

6 7

How to program phone numbers:

You can enter a maximum of nine telephone numbers for the alarms. Each number can be

a maximum of 32 digits. (If you are using this Auto Dialer on an oce/work phone system

you may have to enter 9 before the number to get a line out.)

1. Key in the four digit user password code (factory default is 1234.)

2. Press PROGRAM > 3 > ENTER.

3. The number you press next will select the position in the sequence you want that

telephone number to dial (1= rst number called, 2= second number called, and so on).

4. Press ENTER and key in the rst telephone number.

5. Press ENTER to exit the programming mode.

6. Repeat the process until you have entered all the numbers you wish the Auto Dialer to

call once it has been activated (maximum 9 dierent numbers.)

Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > 1> ENTER > Telephone # > ENTER

How to delete phone numbers:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 3 > ENTER.

3. Press N(N = 1for the rst number called; 2for the second number called; etc.)

3. Press ESC to exit the programming mode.

Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > N> ESC

AD-01 Slave Manual.indd 7 10/15/2009 10:20:44 AM

How to designate telephone numbers to ALARM 1 and ALARM 2:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 6 > ENTER.

3. Press X (X = 1for alarm 1; 2for alarm 2). Press ENTER.

4. Press N (N = 1for rst phone number; 2for second phone number, etc.). Press ENTER.

5. Repeat the process to designate any other numbers to each alarm.

Quick guide: Press 1 2 3 4 > PROGRAM > 6 > ENTER > X> ENTER > N> ENTER

How to change the user password code (factory default is 1234):

1. Key in the four digit user password code (factory default 1234.)

2. Press PASSWORD

3. The LCD will change to n-p.

4. Key in your new four digit user password code.

5. The LCD will change to c-p.

6. Key in your new four digit user password code again.

7. The LCD will change to acc.

Quick guide: Press 1 2 3 4 > PASSWORD > New Code > Conrm New Code

8 9

AD-01 Slave Manual.indd 8 10/15/2009 10:20:45 AM

8 9

How to program the Auto Dialer to give an audible alarm as well as sending a voice

message (factory default is alarm ON):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 1 > ENTER

3. Press N(N = 0for without audible alarm, 1for with audible alarm). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 1 > ENTER > N> ENTER

How to set the time the alarm will sound on activation (default time is 3 minutes):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 2 > ENTER

3. Press Time (Time = 1for one minute, 2for 2 minutes, etc. up to 99 minutes). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 2 > ENTER > Time > ENTER

AD-01 Slave Manual.indd 9 10/15/2009 10:20:45 AM

10 11

How to set Entry/Exit Delay times (default both delay set at 30 seconds):

The entry/exit times are the times the Auto Dialer gives you to enter/exit the area covered

by the system before it arms/alarms. These are pre-set to 30 seconds. You can also change

the timing to instant or 60 seconds.

Entry Delay:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 4 > ENTER

3. Press N (N = 0for instant; 3for 30 seconds; 6for 60 seconds). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 4 > ENTER > N> ENTER

Exit Delay:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 5 > ENTER

Press N (N = 0for instant; 3for 30 seconds; 6for 60 seconds; 9for 90 seconds). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 5 > ENTER > N> ENTER

How to set an Entry/Exit delay sound (factory setting Entry/Exit delay with sound):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 7 > ENTER

3. Press N(N = 0without sound; 1with sound). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 7 > ENTER > N> ENTER

AD-01 Slave Manual.indd 10 10/15/2009 10:20:45 AM

Andere Handbücher für AD-01 Kit

Inhaltsverzeichnis

Andere Dakota Alert Sicherheitssystem Handbücher

Dakota Alert

Dakota Alert AD-01 Kit Bedienungsanleitung

Dakota Alert

Dakota Alert DCPAS-4000 Bedienungsanleitung

Dakota Alert

Dakota Alert CAD-05 Kit GSM Bedienungsanleitung

Dakota Alert

Dakota Alert WPS-1000 Bedienungsanleitung

Dakota Alert

Dakota Alert CAD-03 Kit GSM Bedienungsanleitung

Dakota Alert

Dakota Alert WPS-1000 Bedienungsanleitung

Dakota Alert

Dakota Alert WTS-1000 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung