dallmeier Panomera S4/8 Bedienungsanleitung
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 1/8
Preparation of the Panomera® S4/8
Open the locking ring counterclockwise.
Open the screw on the rear camera cover.
Lift up the upper camera cover.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 2/8
Pull the cover system back and press the
guiding rails together.
Remove the cover system from the housing.
Put the camera on the front side and open the
screw of the lower cover plate.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 3/8
Remove the lower cover plate on the bottom of
the camera.
Put the camera back on its bottom side and
push down the locking pin of the locking ring.
Remove the locking ring.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 4/8
Loosen the screws of the Mountera® Plug.
Remove the Mountera® Plug.
Insert the cover plate removed from the bottom
on the top of the camera.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 5/8
Tighten the cover plate locking screw.
Turn the camera over and insert the Mountera®
Plug on the intended lower mounting surface.
Tighten all four screws.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 6/8
Insert the locking ring.
Loosen the two outer screws of the upper cover
plate from the cover system and remove them.
Insert the cover plate.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 7/8
Tighten the cover plate locking screw.
Retighten the two outer screws of the rear
cover plate.
Insert the rear cover plate into the guiding rails.
Panomera® S4/8
Conversion of the Panomera® S4/8 Mountera® Plug from top to bottom
© 2020 Dallmeier electronic V1.0.0 2020-01-30 8/8
Close the cover plate.
Tighten the fastening screw of the rear
cover plate.
The conversion of the Panomera® S4/8 is
thus completed.
Andere dallmeier Digitalkamera Handbücher
dallmeier
dallmeier Domera DDZ3018-IM/HS Bedienungs- und Wartungsanleitung
dallmeier
dallmeier DDF3000A Bedienungs- und Wartungsanleitung
dallmeier
dallmeier RDF5000 Series Bedienungsanleitung
dallmeier
dallmeier MDF3000A-CS Bedienungs- und Wartungsanleitung
dallmeier
dallmeier MDF5450HD-DN Kurzanleitung
dallmeier
dallmeier Panomera S Series Bedienungsanleitung
dallmeier
dallmeier Panomera W Series Leitfaden
dallmeier
dallmeier SDF6000DN Series Bedienungsanleitung
