Danby DPA140HB1BDB-6 Bedienungsanleitung

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

MODEL •MODÈLE •MODELO

DPA140HB1BDB-6

2019.10.31

PORTABLE AIR CONDITIONER

Owner’s Manual.............................1 - 14

CLIMATISEUR PORTABLE

Manuel du propriétaire.................15 - 28

AIRE ACONDICIONADO PORTÁTIL

Manual del propietario.................29 - 42

Welcome

Welcome to the Danby family. We are proud of our quality products and we believe in

dependable service. We suggest that you read this owner’s manual before plugging in your new

appliance as it contains important operation information, safety information, troubleshooting and

maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance

call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

You must provide the original purchase receipt to validate your warranty and receive service.

Model Number: _________________________________________________

Serial Number: _________________________________________________

Date of Purchase: _______________________________________________

Need Help?

Before you call for service, here are a few things you can do to help us serve you better.

Read this owner’s manual:

It contains instructions to help you use and maintain your appliance properly.

If you receive a damaged appliance:

Immediately contact the retailer or builder that sold you the appliance.

Save time and money:

Check the troubleshooting section at the end of this manual before calling. This section

will help you solve common problems that may occur.

1-800-26- Danby

(1-800-263-2629)

SAFETY REQUIREMENTS

This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless such

persons receive supervision or training to operate

the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they

do not play with the appliance.

To avoid risk of electric shock, do not operate this

appliance in an area that is likely to accumulate

standing water. If this condition develops, disconnect

the power supply before stepping into the water.

Do not store or use combustible materials such as

gasoline or other ﬂammable vapors or liquids in the

vicinity of this or any other appliance.

Do not insert ﬁngers or other objects into grills or

openings in the appliance.

Do not cover or block the intake and exhaust

openings.

Do not operate the appliance without the ﬁlter

installed.

Do not operate the appliance near heat sources.

This appliance is intended for indoor, residential

applications only. Do not use this appliance

outdoors. Do not use this appliance for commercial

or industrial applications.

If the air conditioner is transported on its back or

side, it must be allowed to stand upright for 6 hours

before plugging in to avoid damage to internal

components.

Keep the appliance away from walls, furniture and

curtains with a clearance of at least 30 cm (12

inches) on all sides.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding

reduces the risk of electrical shock by providing an

escape wire for the electrical current.

This appliance has a cord that has a grounding

wire with a 3-prong plug. The power cord must be

plugged into an outlet that is properly grounded.

If the outlet is a 2-prong wall outlet, it must be

replaced with a properly grounded 3-prong wall

outlet. The serial rating plate indicates the voltage

and frequency the appliance is designed for.

WARNING - Improper use of the grounding

plug can result in a risk of electric shock.

Consult a qualiﬁed electrician or service agent

if the grounding instructions are not completely

understood, or if doubt exists as to whether the

appliance is properly grounded.

Do not connect the appliance to extension cords,

adapters or together with another appliance in the

same wall outlet.

Do not splice the power cord. Do not under any

circumstances cut or remove the third ground prong

from the power cord.

If the power supply cord is damaged, it must be

replaced by the manufacturer, its service agent or

similar qualiﬁed person in order to avoid hazard.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

INSTALLATION INSTRUCTIONS

ACCESSORIES

1. Air outlet adapter

2. Exhaust hose

3. Window slider adapter

4. 2 Bolts

5. Window slider A

6. Window slider B and C

7. Foam seal A (adhesive)

8. Foam seal B (adhesive)

9. Foam seal C (non-adhesive)

10.Security bracket and 2 screws

11.Drain hose

12.Power cord storage band

13.Remote control and batteries

REQUIRED TOOLS

1. Medium sized Phillips screwdriver

2. Tape measure or ruler

3. Knife or scissors

4. Saw (in the event that the window sliders need to

be cut to size)

ON/OFF

TEMP

MOD E

FAN

LED

SLEEP SWING

ION

INSTALLATION INSTRUCTIONS

INSTALLING THE WINDOW KIT

The instructions below can be used for either a hung

window or a sliding window application.

1. Measure the window opening where the window

kit will be installed. Assemble as many sliders

as necessary to ﬁt the window. If the window

opening is less that the minimum length of a

single slider, use the slider that has the hole in it

and cut it to the correct length. Make sure not to

cut the end that has the hole as this is necessary

to attach the exhaust hose adapter. Cut the

adhesive foam seals to the correct length for the

window and attach them to the window sash

and frame.

2. Connect the window slider adapter to the

window slider by gently pressing it into the hole

in the slider until it clicks into place.

3. Attach the exhaust hose to the window slider

adapter by gently pressing it into the adapter

until it clicks into place.

4. Install the slider kit and hose assembly and close

the window to hold it in place.

5. Attach the air outlet adapter to the back of the

appliance by sliding it down into the channel

around the air outlet. Attach the hose to the air

outlet adapter on the back of the appliance by

gently pressing it into the adapter until it clicks

into place.

6. Cut the non-adhesive foam seal to match the

width of the window and insert it between the

glass and the window frame to prevent air and

insects from getting into the room.

7. Install the security bracket in the window frame

with the provided screws.

Note: Do not over extend or bend the hose as this

will impede air ﬂow.

OPERATING INSTRUCTIONS

FEATURES

Front

1. Control panel

2. Louver

3. Handle (both sides)

4. Casters

Rear

1. Upper air ﬁlter and air intake

2. Continuous drain outlet

3. Lower air ﬁlter and air intake

4. Air outlet

5. Power cord storage band

6. Power cord

7. Overﬂow tray drain outlet

LOCATION

Place the air conditioner on a smooth, level ﬂoor

that is strong enough to support it and all included

accessories.

Make sure the appliance is level to minimize noise

and vibration.

The appliance must be installed near a grounded

receptacle and the overﬂow drain outlet on the rear

of the appliance must be accessible.

Do not cover air inlets or outlets or the remote

control receiver on the control panel.

The appliance requires 30 cm (12 inches) of

clearance on the front and sides.

The appliance requires at least 50 cm (20 inches) of

clearance on the back.

CONTROL PANEL

1. Swing and wireless connect button:

• Press to start the auto swing feature. When auto

swing is activated, press again to stop the louver

at the desired angle.

• Press and hold for three seconds to start using

the wireless connect feature.

2. Timer button: Press to start the automatic timer.

Light will indicate whether a timer is set.

3. Mode button: Press to select the desired mode.

Light will indicate current mode.

4. Up and down buttons:

• Used to set the temperature and timer.

• Press and hold both up and down buttons for

three seconds to change the temperature display

from °C to °F.

OPERATING INSTRUCTIONS

3sec3sec

123

6 7 8

5. LED display:

• Shows the set temperature in °C or °F.

• Shows the timer settings.

• While on dry or fan mode, shows the room

temperature.

6. Fan and ionizer button:

• Press to select fan speed; low, medium or high.

Light will indicate current speed.

• Press and hold for three seconds to start the

ionizer.

7. Sleep button: Press to start the sleep feature.

8. Power button: Press to turn the appliance on or

off.

OPERATING INSTRUCTIONS

AUTOMATIC TIMER

To set the automatic off timer:

• Ensure the appliance is turned on

• Press the timer button and the indicator light will

illuminate

• Press the up and down buttons to select the

desired amount of hours before the appliance

turns off

To set the automatic on timer:

• Ensure the appliance is turned off

• Press the timer button and the indicator light will

illuminate

• Press the up and down buttons to select the

desired amount of hours before the appliance

turns on

Notes:

• The timer button will increase the time in 0.5

hour increments up to 10 hours and then in 1

hour increments up to 24 hours

• The display will revert back to showing the

previous temperature setting if the appliance

does not receive a signal within a 5 second

period during programming

• Turning the appliance on or off at any time

or adjusting the timer setting to 0.0 hours will

cancel the timer settings

Using Timer On and Off Simultaneously

If there is a need for the appliance to turn on, run

for a set period of time and then turn off, the on

and off timers can be used at the same time by ﬁrst

setting one and then the other. Both indicator lights

will illuminate and the display will count down to

the appliance either turning off or on, whichever

function was set ﬁrst.

Note: The timer will not cycle the appliance on and

off indeﬁnitely. The on and off timers will function

one time and then the appliance will return to

regular functioning.

OPERATING MODES

• Cool Mode

Choose cool mode to set the cooling function. Use

the up and down buttons to choose the desired

temperature. When cool mode is selected, the fan

speed can be adjusted by pressing the fan button.

The temperature can be set within a range of 17 -

30°C (62 - 86°F).

The exhaust hose should be installed during cool

mode to ensure the best results.

• Dry Mode

Choose dry Mode to remove excess moisture

from the air during periods of high humidity. All

water pulled from the air will condense inside the

appliance and drain out the back.

The humidity and fan speed will be automatically set

and cannot be modiﬁed in dry mode.

• Fan Mode

Choose fan mode to run the internal fan without

engaging the cooling function. Press the fan button

repeatedly to choose the fan speed.

• Auto Mode

Auto mode is a pre-set factory program that

automatically deﬁnes the mode and fan speed

based on the set temperature, the ambient

temperature and the ambient humidity.

• Heat Mode

Choose heat mode to set the heating function. Use

the up and down arrows to choose the desired

temperature. Press the fan button to adjust the fan

speed.

The temperature can be set within a range of 17 -

30°C (62 - 86°F).

OPERATING INSTRUCTIONS

FOLLOW ME FUNCTION

There is a temperature sensor built into the remote

control that will continuously collect the current

room temperature. Keep the remote control with

you and the appliance will automatically adjust the

set temperature based on the current temperature

where you are located to reach the most

comfortable condition and temperature.

Press the follow me button to activate the follow

me function. The remote will display the current

temperature at its location. The remote will send

a signal to the air conditioner every 3 minutes, so

long as you remain within range of the appliance.

The follow me light on the control panel of the

appliance will illuminate for 5 seconds every three

minutes to indicate that it has received a signal

from the remote. If the appliance does not receive a

signal from the remote during any 7 minute interval,

it will beep to indicate that the follow me mode has

ended.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

SLEEP FUNCTION

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The sleep function can be canceled at any time by

pressing the sleep button.

IONIZER FEATURE

The ionizer feature is a form of air puriﬁcation that

negatively charges the air. Dust particles, pollen and

other particles in the air cannot pass through the

ﬁlter when they are negatively charged. This ensures

that the maximum amount of dust and dirt are

removed from the air. Additionally, the ionizer helps

to remove unwanted odors from the air.

WIRELESS CONNECTION

This appliance can be controlled with a wireless

application on your wireless device.

Visit https://www.danby.com/support/#apps

to download the application and learn about its

operation.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Power button: Press to turn the appliance on or

off.

2. Mode button: Press to select the desired mode.

3. Fan button: Press to select fan speed.

4. Ionizer button: Press to activate the ionizer.

5. Sleep button: Press to start the sleep feature.

6. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

7. Follow me button: Press to activate the follow

me feature.

8. LED button: Press to turn the LED display on or

off.

9. Timer off button: Press to set the automatic off

timer.

10.Timer on button: Press to set the automatic on

timer.

11.Shortcut button: Press to set and activate the

short cut function.

12.Up and down buttons:

• Used to set the temperature.

• Press and hold both up and down buttons for 3

seconds to change the temperature display from

°C to °F.

13.LED display:

• Shows the set temperature in °C or °F or the

auto-timer settings.

• While on dry or fan mode, shows the room

temperature.

5 6 7 8

Shortcut function (only available on remote):

• Used to save a favourite setting.

• Set the appliance to the temperature and fan

speed that you would like to set as a favourite.

• Press and hold the shortcut button for 2 seconds.

• Press the shortcut button at any point in future to

return to the favourite setting.

• If no favourite is set, pressing the shortcut button

will cause the appliance to run in auto mode at

29°C (79°F), with fan speed set to auto.

Inhaltsverzeichnis

Sprachen:

Andere Danby Klimaanlage Handbücher

Danby

Danby DPAC120090 Montageanleitung

Danby

Danby DAC060ECB4GDB Montageanleitung

Danby

Danby APAC8040 Bedienungsanleitung

Danby

Danby DPA080UB1GDB Bedienungsanleitung

Danby

Danby DAC6007EE Bedienungsanleitung

Danby

Danby Premiere DAC15009EE Montageanleitung

Danby

Danby DAC120EB8WDB Bedienungsanleitung

Danby

Danby Premiere DAC8075EE Bedienungsanleitung

Danby

Danby DAC060EB2GDB Montageanleitung

Danby

Danby DPA120CB5BP Montageanleitung

Danby

Danby DAC080EB1WDB Bedienungsanleitung

Danby

Danby DPA060CB4WDB Bedienungsanleitung

Danby

Danby DPA080CB7WDB Bedienungsanleitung

Danby

Danby DPAC7008 Bedienungsanleitung

Danby

Danby Designer DPAC11012 Bedienungsanleitung

Danby

Danby Premiere DPAC 11010 Montageanleitung

Danby

Danby DPA120E1WDB-6 Bedienungsanleitung

Danby

Danby DTAC100B1WDB-RF Bedienungsanleitung

Danby

Danby DPAC8KBLDB Bedienungsanleitung

Danby

Danby DPA110DHA1CP Montageanleitung

Danby

Danby DPAC11007 Bedienungsanleitung

Danby

Danby Designer DAC12003D Bedienungsanleitung

Danby

Danby DPA080BAUWDB Bedienungsanleitung

Danby

Danby ArcticAire AAC5040 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung