Danby Silhouette DDW2405W Bedienungsanleitung

Installation Instructions Built-In Dishwasher

Model(s):

DDW2405W DDW2405BL DW2406BLS

BEFORE YOU BEGIN: Read

these instructions completely

and carefully.

IMPORTANT: Observe all governing codes

and ordinances.

Note to the Installer: Be sure to leave

these instructions for the consumer’s and local

inspectors use.

Note to Consumer: Keep these instructions

with your Owner’s Manual for future reference.

Skill Level: Installation of this dishwasher

requires basic mechanical and electrical skills.

Proper installation is the responsibility

of the installer. Product failure due to

improper installation is not covered

under the Dishwasher Warranty.

Completion Time 1 to 3 Hours.

New installations require more time than

replacement installations.

IMPORTANT: The dishwasher MUST be installed to

allow for removal from the enclosure in the event

future service is required.

FOR YOUR SAFETY: Read and observe all

CAUTIONS and WARNINGS shown throughout

these instructions. While performing

installations described in this booklet, gloves,

safety glasses or goggles should be worn.

WARNING: To reduce the risk

of electrical shock, fire or

injury to persons, the installer

must ensure that the dish-

washer is completely enclosed

at the time of installation

STOP

ver. 1 07.19.04

READ CAREFULLY.

KEEP THESE

INSTRUCTIONS.

Installation Preparation

PARTS SUPPLIED:

• Two #8 Phillips flat head wood screws 5/8”

long to secure dishwasher to underside of

countertop. (Screws can be found inside the

literature package)

2 Wood Screws

90 Elbow,

Ferrule and

Compression

Nut

Hand Shut-Off

Valve Thread Seal

Tape Wire Nuts (3)

Waste Tee 48” Electrical Cable 72” Stainless Steel

Braided Flex Hose

Air Gap

Screw Type

Hose Clamps

Coupler

Phillips Head

Screwdriver

1/4” & 5/16”

Nut-driver

Level

Flashlight Tube Cutter

Carpenters

Square

6” Adjustable

Wrench

Bucket Safety Glasses

Measuring Tape

Gloves Hole Saw Set

Drill & Bits

MATERIALS YOU WILL NEED: (Not included)

• Ferrule, compression nut and elbow

(3/8” NPT external thread on one end,

opposite end sized to fit water supply)

• Thread seal tape

• cUL Listed wire nuts (3)

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• 48” Electrical cable (power supply)

• Screw type hose clamps

• Hand shut-off valve

• Water line; Stainless steel braided flex hose

• Coupler for extending drain line, if applicable

TOOLS YOU WILL NEED:

• Phillips Head Screwdriver

• 5/16” and 1/4” Nut-driver

• 6” Adjustable Wrench

• Level

• Carpenters Square

• Measuring Tape

• Safety Glasses

• Flashlight

• Bucket to Catch Water

(flushing the line)

• Gloves

• Tube Cutter

• Drill and appropriate bits

• Hole Saw Set

INSTALLATION PREPARATION

PREPARE DISHWASHER ENCLOSURE

• The dishwasher must be installed so that the

drain hose is no more than 10 feet in length for

proper drainage.

• The dishwasher must be fully enclosed on the

top, side and back, and must not support any

part of the enclosure.

Plumbing and

Electric Service

Must Enter

Shaded Area

• The rough cabinet opening must be at least

24” deep and to 24” wide. The opening

should be to 35” max height.

CLEARANCES: When

installed into a corner,

allow 2” min. clearance

between dishwasher and

adjacent cabinet, wall or

other appliances. Allow

25-5/8” min. clearance

from the front of the dish-

washer for the door

opening. Fig. 2

Method 1 Air Gap with Waste Tee or disposer

Method 2 High Drain with Waste

Tee or Disposer

Provide a method to attach drain hose to

underside of countertop.

DRAIN REQUIREMENTS:

• Follow local codes and ordinances.

• Do not exceed 10 feet in distance to the drain.

• Do not connect drain lines from other devices

to the dishwasher drain hose.

• Dishwasher must be connected to waste line

with an air gap (not supplied) or 32” minimum

high drain loop, depending on local codes and

ordinances to prevent back flow into the dish-

washer. Air gap must be used if waste tee or

disposer connection is less than 18” above the

floor to prevent siphoning.

DRAIN PREPARATION:

The type of drain installation depends on answers

to the following questions:

Do local codes or ordinances require installation

of an air gap?

Will waste tee or disposer connection be less

than 18” above the floor?

If the answer to ANY of the 2 questions above is

YES, METHOD 1 MUST BE USED. Otherwise

either Method 1 or Method 2 may be used.

Fig. 3 or Fig. 4

CAUTION:

An air gap MUST BE USED if the drain hose is

connected to waste tee or disposer lower than 18”

above the floor.

Failure to provide the proper drain connection

height with an air gap or 32” minimum high

drain loop will result in improper draining of

the dishwasher.

CABINET PREPARATION:

• Drill a 1-1/2” dia. hole in the cabinet wall within the

shaded areas shown in Fig. 1 for drain hose

connection. The hole should be smooth with no

sharp edges.

Floor must be

even with

room floor.

PREPARE ELECTRICAL WIRING

WARNING:

FOR PERSONAL SAFETY:

Remove house fuse or open circuit

breaker before beginning installation.

Do not use an extension cord or adapter

plug with this appliance.

Electrical Requirements:

• This appliance must be supplied with 120V / 60 Hz.,

and connected to an individual properly grounded

branch circuit, protected by a 15 or 20 ampere circuit

breaker or time delay fuse.

• Wiring must be two wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

Grounding Instructions

This appliance must be connected

to a grounded metal, permanent wiring system, or an

equipment grounding conductor must be run with the

circuit conductors and be connected to the equipment

grounding terminal or lead on the appliance.

WARNING:

Improper connection of the equipment

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if

you are in doubt that the appliance is

properly grounded.

Cabinet Preparation & Wire Routing:

• The wiring may enter the opening from either

side, rear or the floor within the shaded area.

• Cut a 1-1/2” max. dia. hole to admit the electrical

cable. The hole must be free of sharp edges. If

the cabinet wall is metal, the hole edge must be

covered with a bushing/grommet.

• Cable direct connections may pass through the

same hole as the drain hose and hot water line,

if convenient.

Electrical Connection to Dishwasher:

• The electrical connection is located on the right

front side of the dishwasher.

• The cable must be routed as shown in Fig. 5

Cable must extend a minimum of 24” from the

rear wall.

INSTALLATION PREPARATION

PREPARE HOT WATER LINE:

•

The hot water line may enter from either side, rear or

floor within the shaded area shown in Fig. 6

• The line may pass through the same hole as the

electrical cable and drain hose. Or, cut an additional

1-1/2” dia. hole to accommodate the water line.

BEFORE YOU BEGIN

Locate and set aside the package containing the

2 Phillips Head Countertop Mounting Screws.

STEP 1 CHECK DOOR BALANCE

To check the door balance, hold the top of the dish-

washer firmly.

• Open the door slowly, if the door drops when

released, increase spring tension. If the door

closes when released, decrease spring tension.

• Pull the spring adjustment pin out of the holes,

insert into the next highest or lowest hole and

test again.

• Adjust both door springs to the same tension.

• Continue moving the spring pin until the door

is balanced.

CAUTION:

DO NOT OPEN THE DOOR UNTIL

YOU ARE READY TO INSTALL

THE DISHWASHER.

Opening the door will cause the dishwasher to tip forward.

If it is necessary to open the door, hold the top of the

dishwasher securely with one hand and hold the door with

the other hand.

WATER LINE CONNECTION:

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location,

such as under the sink.

• The water connection is located on the left front side of

the dishwasher. Install the hot water inlet line, using a

braided flexible hose (available at most hardware

stores). Route the line as shown in Fig. 6 and extend it

forward at least 18” from the rear wall.

• Adjust water tank (heater) for 120 F to 150 F (49C to

65.5C) temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20 ~ 120psi

INSTALLATION INSTRUCTIONS

STOP

STEP 2 ADJUST LEVELING LEGS

Measure installation height and dishwasher

height. Extend leveling legs out from the dish-

washer base, 1/4” less than installation height.

STEP 3 Remove Kick Plate

Remove the kickplate screws. Lift off the 2 piece

kickplate.

STEP 4 INSTALL 90o ELBOW

Wrap the 90o elbow with thread seal tape, then install

it onto the water valve. To avoid damage to the

water valve bracket and/or fitting, do not over-

tighten the 90oelbow. Position the end of the elbow

to face the rear of the dishwasher.

INSTALLATION INSTRUCTIONS

2 Kickplate

Screws

STEP 5 POSITION WATER LINE AND HOUSE

WIRING

• Position water supply and house wiring on the

floor of the opening to avoid interference with

base of dishwasher and components under

dishwasher.

STEP 7 SLIDE DISHWASHER

PARTIALLY INTO CABINET

TO AVOID DAMAGING THE FRONT PANEL, DO NOT PUSH CABINET IN WITH KNEES.

• Slide dishwasher into the opening a few inches at

a time.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the

dishwasher is a few inches forward of adjacent

cabinetry.

• Make sure drain hose is not kinked under the

dishwasher and there is no interference with the

waterline and wiring or any other component.

STEP 6 INSERT DRAIN HOSE

THROUGH CABINET

• Position the dishwasher in front of he opening.

Insert drain hose into cabinet wall hole.

TIP: Position water line and house wiring on the floor

to avoid interference with base of dishwasher.

INSTALLATION INSTRUCTIONS

STEP 8 POSITION DISHWASHER UNDER COUNTERTOP

• Check to be sure that wires are secure under the

dishwasher and not pinched or in contact with

door springs or other dishwasher components.

TIP: Check tub insulation blanket.

It should be positioned so it is not bunched up or

interfering with door springs. Check by opening

and closing door.

• Push dishwasher into cabinet. The front corners

of the dishwasher door should be flush with

cabinet doors. Be careful not to dent front panel

with knees or damage countertop or cabinets

with dishwasher parts.

STEP 9 LEVEL DISHWASHER

IMPORTANT -

Dishwasher must be

level for proper dish rack operation and

wash performance.

TIP: Pull lower rack out, about halfway. Check

to be sure the rack does not roll forward or

back into dishwasher. If the rack rolls in either

direction, the dishwasher must be leveled

again.

• If the door hits the tub, the dishwasher is not

installed correctly. Adjust leveling legs to align

door to tub.

• Level the

dishwasher by

adjusting the four

leveling legs

individually.

• Place level on door

and rack track inside

the tub as shown to

check that the dish-

washer is level.

INSTALLATION INSTRUCTIONS

STEP 10 SECURE DISHWASHER

TO CABINET

The dishwasher must be secured to

the countertop.

• Position the dishwasher so that the tub flange

aligns with the front face of the cabinet frame.

IMPORTANT -

Check to be sure the dishwasher

is centered in the opening and there is no interfer-

ence with the adjacent cabinets when opening or

closing the door.

• Fasten the dishwasher to the underside of the

countertop with the 2 Phillips screws provided.

IMPORTANT -

Drive screws straight and flush.

Protruding screw heads will scratch the top of the

control panel and can interfere with door

opening/closing.

STEP 11 CONNECT WATER

SUPPLY

Connect water supply line to 90oelbow.

Method 1 - Braided flex hose

• Connect the stainless steel braided flex hose

directly to the 90oelbow (as show in Figure 19)

IMPORTANT -

Check to be sure that door spring

does not rub or contact the fill hose or water supply

line. Test by opening and closing the door. Re-route

the lines if a rubbing noise or interference occurs.

INSTALLATION INSTRUCTIONS

STEP 12 CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES

AND ORDINANCES

The drain hose molded end will fit 5/8”, 3/4” or 1”

diameter connections on the air gap, waste tee or

disposer. Cut the marked line as required for your

installation.

• If a longer drain hose is required, add up to 42”

length for a total of 10ft. to the factory installed

hose. Use 5/8” or 7/8” inside diameter hose and

a coupler to connect two hose ends. Secure the

connection with hose clamps.

• Secure the drain hose to the air gap, waste

tee or disposer with clamps.

NOTE:

TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED

10 FEET FOR PROPER DRAIN OPERATION.

DRAIN LINE INSTALLATION

• Connect drain line to air gap, waste tee or disposer

using either of the previously determined method.

Method 1 - Air gap with waste tee or disposer

Method 2 - High drain loop with waste tee or disposer

IMPORTANT -

When connecting the drain line to

the disposer, check to be sure that

the drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

TIP: Avoid unnecessary service call charges. Always

be sure disposer drain plug has been removed before

attaching dishwasher drain hose to dispenser.

INSTALLATION INSTRUCTIONS

Andere Handbücher für Silhouette DDW2405W

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Danby Spülmaschine Handbücher

Danby

Danby Designer DDW1805W Bedienungsanleitung

Danby

Danby DDW396W Bedienungsanleitung

Danby

Danby Designer DDW1805W Bedienungsanleitung

Danby

Danby Silhouette DDW2405W Bedienungsanleitung

Danby

Danby DDW18D1EW Bedienungsanleitung

Danby

Danby Designer DDW399W Bedienungsanleitung

Danby

Danby DDW1899BLS Kurzanleitung

Danby

Danby DDW496W Bedienungsanleitung

Danby

Danby DDW1805EWP Bedienungsanleitung

Danby

Danby DDW18D1EW Bedienungsanleitung

Danby

Danby DDW621WDB Bedienungsanleitung

Danby

Danby DDW1801MW Bedienungsanleitung

Danby

Danby DDW1899BLS-1 Montageanleitung

Danby

Danby DDW1899BLS Montageanleitung

Danby

Danby DDW1832ESS Bedienungsanleitung

Danby

Danby Silhouette DDW2405W Bedienungsanleitung

Danby

Danby Designer DDW1802W Bedienungsanleitung

Danby

Danby DDW496W Bedienungsanleitung

Danby

Danby Designer DDW1802W Bedienungsanleitung

Danby

Danby DDW1804EW Bedienungsanleitung

Danby

Danby Designer DDW1805W Bedienungsanleitung

Danby

Danby DDW631WDB Bedienungsanleitung

Danby

Danby DDW1809W Montageanleitung

Danby

Danby DDW1802 - 14352 Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

KitchenAid

KitchenAid KUDB230B Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung