Danby DDEF03813BD13 Bedienungsanleitung

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

www.Danby.com

2022.08.18

ELECTRIC FIREPLACE WITH HEATER

Owner’s Manual.............................1 - 14

FOYER ELECTRIQUE AVEC CHAUFFAGE

Manuel du propriétaire.................15 - 28

CHIMENEA ELÉCTRICA CON CALENTADOR

Manual del propietario.................29 - 42

MODEL •MODÈLE •MODELO

DDEF03813BD13

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

• WARNING: Read and understand this entire owner’s manual,

including all safety information, before plugging in or using this

ﬁreplace. Failure to do so could result in ﬁre, electric shock or serious

personal injury.

• CAUTION: Keep this owner’s manual for future reference.

• CAUTION: Risk of electric shock. Do not open or try to repair the

ﬁreplace yourself.

• This ﬁreplace may get hot when in use. To avoid burns, do not let

bare skin touch hot surfaces.

• Keep combustible materials, such as furniture, pillows, bedding,

paper, clothes and curtains at least 3 feet from the front of the

ﬁreplace and keep them away from the sides, top and rear. Do not

place towels or other objects on the ﬁreplace.

• Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating and

unattended.

• The ﬁreplace is not intended for use in bathrooms, laundry areas,

showers or swimming pools and similar locations. Never locate the

ﬁreplace where it may fall into a bathtub or other water container. To

protect against electrical hazards, do not immerse the power cord in

water or other liquids.

• Do not touch the control panel or plug with a wet hand.

• Always use on a dry, level surface.

• Do not use outdoors.

• Always use in an upright position.

• Do not attempt to repair or adjust any electrical or mechanical

functions on this ﬁreplace. Doing so will void your warranty. The

inside of the ﬁreplace does not contain any user serviceable parts.

• Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock or ﬁre or

damage to the ﬁreplace.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

• WARNING: To reduce the risk of ﬁre or electric shock, do not use this

ﬁreplace with any solid-state speed control devices.

• Do not operate any ﬁreplace with a damaged power cord or after

the ﬁreplace malfunctions, has been dropped or damaged in any

manner. Return the ﬁreplace to an authorized service facility for

examination, electrical or mechanical adjustment or repair.

• Do not run the power cord under carpeting. Do not cover the power

cord with throw rugs, runners or similar coverings. Arrange the

power cord away from trafﬁc area where it will not be tripped over.

• To prevent possible ﬁre, do not block the air intakes or exhaust in any

manner. Do not use the ﬁreplace on soft surfaces like a bed or thick

carpeting where the air intakes may become blocked.

• This ﬁreplace has hot and arcing or sparking parts inside. Do not

use the ﬁreplace in areas where gasoline, paint, explosive and/or

ﬂammable liquids are used or stored. Keep the ﬁreplace away from

heated surfaces and open ﬂames.

• To avoid ﬁre or shock hazard, plug the ﬁreplace directly into a 120 V

AC electrical outlet. Never use an extension cord or power strip.

• To disconnect the ﬁreplace, turn the controls to off and then remove

the plug from the outlet. Pull ﬁrmly on the plug, do not unplug by

pulling on the cord.

• Always unplug the ﬁreplace before moving or cleaning it. Unplug the

ﬁreplace when it is not in use.

• Use only for intended household use as described in this manual.

Any other use not recommended by the manufacturer may cause

ﬁre, electric shock or injury to persons. The use of attachments is not

recommended.

OPERATING INSTRUCTIONS

OVERHEAT SAFETY FEATURE

This ﬁreplace is equipped with an overheat safety feature. When the

ﬁreplace’s internal components reach a certain temperature that could

cause overheating and possible ﬁre, the ﬁreplace will automatically shut

off. Operation can only resume when the user resets the ﬁreplace.

To reset the ﬁreplace, ensure the power is turned off, unplug the unit and

wait 15 to 20 minutes for the internal components to cool down.

Follow the instructions for use to return the ﬁreplace to normal

functioning.

WARNING: It is normal for the power cord to feel warm to the touch;

however, a loose ﬁt between the outlet and the plug may cause

overheating of the plug. If this occurs, try inserting the plug into a

different outlet. Contact a qualiﬁed electrician to inspect the original

outlet for damage.

INCLUDED ACCESSORIES

• Electric ﬁreplace with heater

• Remote control

• Clear crystals

• Wall hanging bracket

• Wall hanging bracket hardware:

• 4 x 45 mm screws x4

• Four screw expansion brackets

• 4 x 12 mm screws x2

• Two feet

• 4 x 16 mm screws x8 (to assemble feet)

IMPORTANT WARNING

Do not leave this appliance unattended in a space where people

or animals who cannot react to a malfunction are located. A

malfunction can cause extreme overheating or death in an

enclosed, unattended space.

OPERATING INSTRUCTIONS

FEATURES

1. Glass

2. Air outlet

3. Control panel

4. Power switch

5. Wall hanging bracket

6. Ember bed

7. Free standing feet

OPERATING INSTRUCTIONS

CONTROL PANEL

1. Timer indicator light: Illuminates when the timer is active.

2. Display panel: Shows the set temperature.

3. High heat mode indicator: Illuminates when high heat mode is active.

4. Low heat mode indicator: Illuminates when low heat mode is active.

5. Power button: Used to turn the ﬁreplace on or off.

6. Mode button: Used to set the desired mode; low heat or high heat.

Press and hold for 3 seconds to change between °F and °C.

7. Flame colour button: Used to turn the ﬂame on or off. Used to change

the colour of the ﬂame.

8. Timer button: Used to set the timer feature. Press the timer button

repeatedly to set the number of hours that the ﬁreplace should run

before turning off. The timer can be set between 0 and 12 hours

and can be adjusted in 1 hour increments. The timer indicator light

will remain illuminated while the timer is active. The ﬁreplace will

automatically turn off when the timer reaches zero.

9. Up and down buttons: Used to increase or decrease the set

temperature.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Power button: Used to turn the ﬁreplace on or off.

2. Mode button: Used to set the desired mode; low heat or high heat.

3. Flame colour button: Used to turn the ﬂame on or off. Used to change

the colour of the ﬂame.

4. Timer button: Used to set the timer feature.

5. Up and down buttons: Used to increase or decrease the set

temperature.

3 4

1 2

REMOTE CONTROL BATTERY

This remote control uses one CR2025

battery.

To remove the battery, push the latch

on the battery compartment upwards

and then pull the battery tray out.

To replace the battery, place the new

battery in the battery tray and push it

gently into the remote control until it

clicks into place.

WARNING: Never dispose of

batteries in ﬁre. Failure to observe this

precaution may result in an explosion.

Dispose of batteries at your local

hazardous material processing center.

If the ﬁreplace will not be used for

a long time, remove the batteries to

prevent corrosion. Store the remote

control in a safe place.

Remove the insulating ﬁlm from the

battery compartment before using the

remote control.

WARNING:

• Keep batteries out of childrens’

reach. Discard them carefully.

• Do not allow children to play with

batteries.

• Never put button batteries in or

near your mouth for any reason,

they are slippery and easy to

swallow accidentally.

OPERATING INSTRUCTIONS

INSTRUCTIONS FOR USE

1. Remove the insulating ﬁlm from the remote control battery

compartment.

2. Ensure the power is turned off.

3. Decide which installation method to use and install the ﬁreplace as

directed.

4. Plug the ﬁreplace directly into a 120V AC electrical outlet.

5. Turn the ﬁreplace on by pressing the power button.

6. Press the mode button to set low or high heat mode.

7. Press the up and down buttons to set the desired temperature. The

ﬁreplace will remain on until the set temperature is reached and it

will then cycle on and off to maintain the set temperature.

8. Turn the ﬁreplace off by pressing the power button. When the power

is turned off the heating element will stop working immediately but

the fan will continue to run for 30 seconds or until the ﬁreplace has

cooled.

Important

When the heat feature is used for the ﬁrst time, a slight odor may be

present. This is normal and should not occur again unless the ﬁreplace is

not used for an extended period of time.

It is normal for the ﬁreplace to cycle on and off as it maintains the set

temperature.

For the ﬁreplace to function properly, the set temperature must be higher

than the ambient temperature in the room. If the ﬁreplace does not

seem to be heating, increase the set temperature to engage the heating

element.

INSTALLATION INSTRUCTIONS

PREPARATION

WARNING: This product includes glass. Always use extreme caution

when handling glass. Failure to do so could result in personal injury or

property damage.

Remove all parts and hardware from the carton and place them on a

clean, soft, dry surface.

WARNING: Make sure all parts are dry and the power cord and plug

are not damaged. See the Important Instructions section.

The ﬁreplace can be wall-mounted or placed on a solid, level surface

when the free standing feet are assembled. The ﬁreplace must be

plugged into a 120V 60Hz electrical outlet.

FREE STANDING FOOT ASSEMBLY

Carefully lay the ﬁreplace on a ﬂoor or table. Place the ﬁreplace on a

blanket or soft surface to avoid scratching it or causing damage to your

furniture or ﬂooring.

Attach the free standing feet using eight 4 x 16 mm screws as shown.

Place upright on a solid, level surface and plug into a 120V 60Hz

electrical outlet.

Note: If you attach the solid feet for freestanding installation, you do not

need to install the wall bracket onto the back of the ﬁreplace.

Andere Handbücher für DDEF03813BD13

Inhaltsverzeichnis

Sprachen:

Andere Danby Kamin im Innenbereich Handbücher

Danby

Danby DDEF02213BD13 Bedienungsanleitung

Danby

Danby DDEF03813BD13 Bedienungsanleitung

Danby

Danby DDEF02213BD13 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch