Danby DPA120HB1WDB Bedienungsanleitung

Thank you for purchasing a Danby air conditioner. Please

read this onwer’s manual carefully before using your new

air conditioner.

Remote Control Instructions

MODEL

AIR CONDITIONER

DPA120HB1WDB

DPA140HB1WDD

02.01.14

DPA140HB1BDD

Handling the Remote Control...................................................

Function Buttons ......................................................................

Indicators on LCD Display .......................................................

Operating the Buttons ..............................................................

Auto Operation Setting .............................................................

Swing Setting.............................................................................

Timer Setting..............................................................................

Economy Setting........................................................................

CONTENTS

Remote Control Specifications................................................

Cooling/ Fan Setting .................................................................

Dehumidifier Setting .................................................................

Use the remote control within a distance of 8

meters from the appliance, pointing it towards the

receiver. Reception is confirmed by a beep.

Location of the Remote Control.

CAUTIONS

The air condiitioner will not respond if curtains, doors or other materials

block the signal from the remote control to the unit. esopxetonoD.lortnocetomerehthtiwtcatnocmorfdiuqilynatneverP

the remote control to direct sunlight or heat.

If the infrared signal receiver on the indoor unit is exposed to direct

sunlight, the air conditioner may not function properly. Use curtains to

prevent the sunlight from falling on the receiver.

If other electrical appliances react to the remote control,either move

these appliances to another location or consult your local dealer..

The remote control is powered by two dry

part and protected by a cover.

(1) Remove the cover by pressing down and sliding it off.

(2) Remove the old batteries and insert the new

batteries,placing the(+) and (-) ends correctly.

(3) Reattach the cover by sliding it back into

position.

NOTE: When the batteries are removed, the

remote control erases all programming.

After inserting new batteries, the remote

controll must be reprogrammed.

Replacing the Batteries

Handling the Remote Control

batteries(2-AAA) located in the rear

Model

Rated Voltage

Remote Control Specifications

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range: 17°C ~30°C (62°F~86°F).

4. Full Function of LCD (Liquid Crystal Display)

Environment

Signal Receiving Range

Performance Feature

CAUTION

Do not mix old and new batteries or batteries of different types.

Do not leave the batteries in the remote controller if it is not going

to be used for more than 2 months.

Dispose of the old batteries in special containers such as those

foundin the sales outlets.

NOTE:

All the illustrations in this manual are for explanatory purposes only.

Your air conditioner may be

NOTE :

3.0V(

2-AAA

)

1. Operating Mode: AUTO, COOL, DRY,

and FAN.

RG 51I46/BGE

-5°C to 60°C (-41°F to 140°F)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

1) Reorient or relocate the receiving antenna

2) Increase the separation between the equipment and receiver

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4) Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not approved by the party responsible for FCC compliance could void the user’s

authority to operate the equipment.

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired

operation.

CAN ICES-3 (B) / NMB-3 (B)

Temperature setting display: press and hold the UP and DOWN buttons at the same time for

3 seconds to alternate the temperature display between °C and °F.

Function Buttons

nottuBNWODPMET

Push this button to decrease the indoor temper-

ature setting by 1°C (2°F) increments to 30°C (86°F)

nottuBPUPMET

Push this button to increase the indoor temper-

ature setting by 1°C (2°F) increments to 17°C (62°F)

Each time the button is pressed, the operation

mode changes in the following sequence:

MODE Button

Used to stop or start louver movement and

move the airflow direction up/down as desired.

Button

Once the recessed RESET button is pressed,

all of the current settings will be cancelled

and the controller will return to default settings.

Button

Operation starts when this button is pressed

and stops when the button is pressed again.

AUTO

COOL

DRY

FAN

Used to select the fan speed in four steps:

Auto Low Med High

Button

Press this button to activate the Auto-on time

setting. Each time it’s pressed will increase the start

time by 30 minute increments, up to 10 hours, then

by 1 hour increments up to 24 hours.To cancel the

Auto-on time setting, just press the button until

the time setting is 0.0.

Button

Select this function if you want the unit to maintain

a comfortable setting and save energy while you sleep.

mode only.

Model: RG51I46/BGE

Button

This function is available on COOL, or AUTO

Press and hold the UP and DOWN buttons at the same

time for 3 seconds to alternate the temperature display

between °C and °F.

Function Buttons (continued)

Button: Press the timer button to activate

the AUTO-OFF setting. Each time it’s pressed

increases the time setting by 30 minute increments

for the first 10 hours, then by 1 hour increments up

to 24 hours. To cancel the AUTO-OFF setting, press

the button until the setting displays 0.0.

Button: Press this recessed button to lock all

current settings, and the remote control will not

accept any changes except for unlocking. Use the

LOCK mode when you want to prevent settings from

changing accidentally. Press the LOCK button again

to cancel the LOCK function. A LOCK symbol will

appear on the remote control display when the

LOCK function is activated.

LED Display Button: Press this button to clear the

unit’s display, press it again to light the display.

NOTE: While the unit is running in sleep mode, it

MODE buttons

are pressed. ro,,filecnaclliw

TIMER ON OFF

SET TEMPERATURE

Transmission Indicator

Temp./Timer Display

FAN SPEED Display

MODE display

ON/OFF Display

This transmission indicator will light up when the remote

control transmits signals to the indoor unit.

Displays the current selected mode. Including AUTO,

COOL, DRY

, and FAN.

The temperature setting, from 17°C (62°F)

30°C (86°F) or timer setting (0~24h) will be displayed.

If FAN mode is selected, there will be no display

This indicator will be displayed when the unit is

operating.

Displays the selected fan speed: AUTO, HIGH, MED

or LOW. Nothing is displayed when the fan speed is

on AUTO speed. WhenAUTO or DRY Mode are

selected, there will be no signs displayed.

MODE Display (FAN mode)

Indicators on the LCD

TIMER DISPLAY:

This display area shows the TIMER settings. That is, if

only the Auto-on function is set, it will display TIMER

ON. If only the Auto-off time function is set, it will

display TIMER OFF. If both functions are set, it will

display TIMER ON OFF which indicates you have

chosen both the Auto-on and Auto-off setting.

LOCK INDICATOR:

The LOCK icon is displayed after pushing the LOCK

button. Push the LOCK button again to clear display.

Ensure theunit isplugged inand has power.

How to use the buttons

Auto Operation

Ensure that the unit is plugged in and has power.

The OPERATION indicator will illuminate on the

display panel of the unit.

1. Press the MODE button until AUTO is selected.

2. Press the TEMP button to set the desired

temperature. The temperature can be set within a

range of 17°C (62°F) to 30°C (86°F) by 1°C (2°F)

increments.

conditioner.

NOTE

1. In the auto mode, the air conditioner can

automatically choose the mode of Cooling, Fan,

difference between

the actual room temperature

and the set

temperatrue on the remote control.

2. In the auto mode, you can’t switch the fan speed.

3. If the auto mode doesn’t suit you, the desired

mode can be controlled manually.

Cooling / Fan Operation

1. Press the MODE button to select COOL,

FAN mode.

2. Press the TEMP button to set the desired

temperature. The temperature can be set within a

range of 17°C (62°F) to 30°C (86°F) in 1°C (2°F)

increments.

3. Press the button to select one of

4 fan speeds -Auto, Low, Med, or High.

4. Press the button to start the air

conditioner.

NOTE

In the FAN mode, the temperature setting is not

displayed in the remote control and you are not

able to control the room temperature either. In this

case, only step 1, 3, and 4 may be performed.

Dehumidifying by sensing the

3. Press the button to start the air

)F°2(C°1ni)F°68(C°03~)F°26(C°71foegnaranihtiw

Ensure theunit isplugged inand has power.

The

OPERATION

indicator onthe display

panel of

the unit

illuminates.

Swing Setting

airflow direction.

2 seconds, the auto-swing feature of the louver

is activated. The horizontal louver will swing

up/down automatically. Press it again to stop.

NOTE: When the louver swings or moves to a

position which would affect the cooling

it will

automatically change the swing/

moving

direction.

Dehumidifying Setting

selected.

2. Press the TEMP button to set the desired

temperature. The temperature can be set within a

range of 17°C (62°F) to 30°C (86°F) by 1°C (2°F)

increments.

ing mode.

Use the button to adjust the Up/Down

ability of the air conditioner,

1. Press the MODE button until DRY mode si

3. Press the

button to start dehumidify-

1. If the button is held down for more than

time of the unit. Pressing the button

Timer Setting

will set the auto-off time of the unit.

control will display TIMER ON, the last auto-on

time setting and the LCD display area will show

an ‘h.’ Now it’s ready to reset the auto-on time.

auto-on time. Each time you press the button,

the time increases by 30 minute increments, up

to 10 hours, then by 1 hour increments up to 24

hours.

3. After turning the TIMER ON, there will be a one-

half second delay before the remote control

transmits the signal to the air conditioner. Then,

after approximately 2 more seconds, the “h”

will disappear and the set temperature will

re-appear on the LCD display window.

To Set theAuto-On Time.

To Set theAuto-Off Time.

control will show TIMER OFF, the last auto-off

time setting, and the LCD display area will show

an “h.” Now it is ready to reset the auto-off time.

desired auto-off time. Each time you press the

button, the time increases by 30 minute

increments up to 10 hours, then by 1 hour

increments up to 24 hours.

3. After setting the TIMER OFF ,there will be a one-

half second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "h" will disappear and the set temperature

will re-appear on the LCD display window.

Pressing the

button will set the auto-on

1. Press the button. The remote

2. Push the button again to set the desired

1. Press the button. The remote

2. Push the button again to set the

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Danby Fernbedienung Handbücher

Danby

Danby DPA100E1WDB Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung