Danelec DM100 S-VDR Bedienungsanleitung

Operator’s Manual

For the DM100 S-VDR

Document Number DBS10912

Version Number 1.0

Date October 2014

P/N (hard copy) 9302539-10

Operator's Manual for the DM100 S-VDR

Revision record

Version

Date

Description

1.0

October 2014

Original issue of document

DBS10912-10 Page 2/36

Operator's Manual for the DM100 S-VDR

Contents

REVISION RECORD ...........................................................................................................2

1SCOPE AND PURPOSE ...........................................................................................5

1.1 References.................................................................................................................5

1.2 Terms and Abbreviations ...........................................................................................5

2SYSTEM OVERVIEW................................................................................................6

2.1 System overview for an S-VDR..................................................................................6

2.1.1 Data Acquisition Unit (DAU) ................................................................................6

2.1.2 Bridge Alarm Unit (BAU)......................................................................................6

2.1.3 Bridge Microphone Units (BMU)..........................................................................6

2.1.4 Fixed Data Capsule.............................................................................................6

2.1.5 Float-free data capsule........................................................................................7

2.1.6 Remote video interface (RVI) ..............................................................................7

3OPERATION..............................................................................................................9

3.1 Bridge alarm Unit .......................................................................................................9

3.1.1 Alarm display.......................................................................................................9

3.1.2 Method for initiating a backup on the VDR data disk...........................................9

4OPERATION DM100 DAU ......................................................................................11

4.1 DPU .........................................................................................................................12

4.1.1 Power LEDs ......................................................................................................12

4.1.2 AC breaker ........................................................................................................12

4.1.3 AC inlet..............................................................................................................12

4.1.4 Battery switch ....................................................................................................13

4.1.5 VDR status LED ................................................................................................14

4.1.6 Main CPU LED ..................................................................................................14

4.1.7 LEDs in the Ethernet connectors.......................................................................14

5OPERATION OF STANDARD RVI 02-004 AND RVI 02-004D (POE) ....................15

6OPERATION OF RVI WITH AC POWER SUPPLY.................................................16

6.1.1 RVI address.......................................................................................................16

6.1.2 Ethernet ports....................................................................................................16

6.1.3 ST LED..............................................................................................................16

7ERROR CODES ......................................................................................................17

7.1 Error codes for a basic S-VDR installation...............................................................17

7.2 Additional error codes for installations utilizing a SIU and 2nd RVI...........................23

8SERVICE AND MAINTENANCE .............................................................................25

DBS10912-10 Page 3/36

Operator's Manual for the DM100 S-VDR

8.1Verification of the S-VDR functionality following service on any sensor...................25

8.2 Setting the IP address of the PC, windows 7 ...........................................................26

8.3 Connecting the PC to the S-VDR.............................................................................29

8.3.1 Run the VDR Verifier program...........................................................................29

8.3.2 Examination of the report ..................................................................................32

8.4 List of most common spare parts .............................................................................36

DBS10912-10 Page 4/36

Operator's Manual for the DM100 S-VDR

1 Scope and purpose

Operator's Manual for the DM100 S-VDR

1.1 References

DBS10704 Installation Manual for DM100/DM400 VDR compact Sensor Interface Unit

DBS10885 Installation Manual for DM100 S-VDR

DBS10911 Inspectors and Authorities Manual for DM100 S-VDR

DBS10919 Installation manual for Remote Video Interface RVI 02-004(D)

1.2 Terms and Abbreviations

BAU Bridge Alarm Unit

BMU Bridge Microphone Unit

DAU Data Acquisition Unit

DPU Data Processing Unit (located inside the DAU)

SIU Sensor Interface Unit

RVI Remote Video Interface

NAS Network Attached Storage (option used for external extended backup)

DBS10912-10 Page 5/36

Operator's Manual for the DM100 S-VDR

2 System overview

2.1 System overview for an S-VDR

The S-VDR is composed of the following units:

S-VDR System overview (typical configuration)

2.1.1 Data Acquisition Unit (DAU)

The Data Acquisition Unit contains the Data Processor Unit (DPU). The DAU must be installed

indoors in the proximity of the bridge.

2.1.2 Bridge Alarm Unit (BAU)

The BAU must be installed on the bridge either in a console or mounted on a bulkhead. System

errors will generate a visual and audible alarm.

2.1.3 Bridge Microphone Units (BMU)

A number of BMUs must be installed on the bridge (console, ceiling or bulkhead mounted).

Watertight outdoor BMUs for the bridge wings are available.

2.1.4 Fixed Data Capsule

The data capsule (“the orange box”) must be installed on an “external deck close to the vessel’s

center line”; typically on the external deck above the bridge.

BMU

DAU

BAU

Capsule

BMU

VHF

Serial inputs (12)

e.g. GPS

Video inputs (2) for

RADAR

RS-422

Power

Ethernet PoE

STP CAT5

Remote

video I/F

Ethernet PoE

STP CAT5

5 x BMU

DBS10912-10 Page 6/36

Operator's Manual for the DM100 S-VDR

2.1.5 Float-free data capsule

As an alternative to the fixed data capsule, a float-free capsule may be used instead.

2.1.6 Remote video interface (RVI)

RADAR video is acquired using a Remote Video Interface (RVI). The RVI must be installed

indoors; typically close to the RADARs. It must be connected to the DAU with a cable which may

be up to 100m long.

DBS10912-10 Page 7/36

Operator's Manual for the DM100 S-VDR

2.1.6.1 Maximum number of supported interfaces

If needed, additional equipment may be used to make larger or non-standard configurations. The

maximum number of supported interfaces for an S-VDR is listed below:

Interface type

Maximum configuration

Serial inputs

28 (12 on DAU + 2 modules)

Analog inputs

32 (2 modules)

Digital inputs

128 (8 modules)

Audio inputs

18 (10 on DAU + 8 on RAI)

Video inputs

4 (2 RVIs)

DBS10912-10 Page 8/36

Operator's Manual for the DM100 S-VDR

3 Operation

3.1 Bridge alarm Unit

The BAU is the primary user interface for an installed operational S-VDR. It serves two purposes:

•Alarm display

•Interface for initiating a backup on the VDR data disk

3.1.1 Alarm display

The S-VDR will generate an alarm message if a system error is detected. The alarm messages will

be displayed on the BAU. An audible alarm will be generated with each new alarm and the error

LED will start flashing. Pressing ACK will mute the audible alarm. The error LED will be

illuminated as long as there is any error in the system, the cause of the error(s) will be displayed in

the LCD display.

3.1.1.1 Protection against intermittent errors

Intermittent errors can be a source of irritation. The S-VDR will regard a system component or a

data source which fails 3 times within 12 hours as permanently failed; i.e. that system

component/data source will not be able to generate more audible alarms. A permanent visual alarm

will be displayed instead and the S-VDR will still try to recover from the problem, e.g. record data

even if is contains many errors. Repetitive alarms are marked with an “R” after the error code.

The “repetitive” error status for a failed system component/data source will be automatically reset if

no error has been generated for 12 hours. The “Purge List” button on the BAU will force reset of

“repetitive” error status for all system components/data sources.

3.1.1.2 Dimming

The button with the light bulb symbol may be used to alter the brightness of the keyboard, error

LEDs and the LCD display simultaneously.

3.1.2 Method for initiating a backup on the VDR data disk

The S-VDR system is only guaranteed to record data for twelve hours, i.e. important data may be

overwritten after twelve hours unless a backup of data is made following an incident.

The crew on the bridge must initiate the backup procedure shortly after the ship has been involved

in an incident or if an incident involving other vessels is observed.

The backup procedure is started when the two “Save” buttons are pressed simultaneously. The S-

VDR is able to make the backup within seconds.

The system is capable of storing three incidents. The “Save” LED indicates when there is multiple,

one or no save opportunity left (disk full). A backup will be protected for 30 days after which the

space on the disk will be released automatically.

DBS10912-10 Page 9/36

Operator's Manual for the DM100 S-VDR

This VDR data disk must be replaced if it becomes full (which is unlikely under normal

circumstances). Alternatively, data from the disk must be transferred to another media, and space on

the disk can be manually released. This requires proper authorization and cannot be done from the

BAU.

The VDR data disk, which is easily removed from the DAU, must be retrieved if the vessel is

abandoned after a serious incident.

DBS10912-10 Page 10/36

Inhaltsverzeichnis

Andere Danelec Datenlogger Handbücher

Danelec

Danelec DM100-2014 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung