Danfoss Link SCM Bedienungsanleitung
MAKING MODERN LIVING POSSIBLE
Danfoss Heating Solutions
Danfoss Link™ SCM
Simple Communication Module
Installation Guide
2VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
Introduction .................................................. 5
Installation ................................................... 5
Mounting..................................................... 5
Wiring ........................................................ 6
Adding the device ............................................ 6
Perform network test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmission test (optional) ................................... 7
Factory reset.................................................. 7
Status indicator ............................................... 7
Getting started with Danfoss Link™ SCM ....................... 8
Technical specications ....................................... 9
Disposal instructions .......................................... 9
Table of Contents
3
VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
The Danfoss Link™ SCM (Simple Communication Module) is an
electronic controller for turning the Away function ON/OFF in a
Danfoss Link™system.
The Danfoss Link™ SCM is powered by 230 V~.
Introduction
Installation
The Danfoss Link™ wireless system’s transmission range is suf-
cient for most applications; however each building has dierent
obstacles aecting communication and maximum transmission
distance.
If communication problems occur Danfoss suggests to support
the system with repeaters. In exceptional cases the wireless
system may not be suitable for your installation.
Note: Be aware that installation and placement must be according
to local building regulations.
Mounting
GB
4VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
Wiring
The process of adding the Danfoss Link™ SCM
to a system is performed on the Danfoss
Link™ CC.
Note that the Danfoss Link™ SCM
must be added as a Service
Device.
When adding, press and
release the install button,
and observe that the LED
gives a fast green ash.
If adding is successful the LED turns green (HOME) or red (AWAY)
permanently - depending on input stage.
For further information, see the Danfoss Link™ CC installation
guide.
Note: If adding the Danfoss Link™ SCM to the Danfoss Link™ CC is
unsuccessful, make sure the right Danfoss Link™ CC software
version is applied. Correct version: 2.5.57 or higher.
Adding the device
1.
2.
PWR+
NC
COM
PWR-
Note: Refer to the Danfoss Link™ Mobile Phone Butler (Danfoss
Link™ MPB) manual for wiring connections to the Danfoss
Link™ MPB.
Black (+)Black/white (-)
5
VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
Green LED ON Away OFF
Red LED ON Away ON
Green LED fast ash Adding or link test
Green LED short ash Ready for adding
Red LED slow ash
for 5 seconds Adding not OK
Red LED slow ash
continously
Transmission test not OK or lost
connection to Danfoss Link™ CC
Status indicator
Turn o the power to the device, then press and hold the install
button in front of the device for approx. 5 seconds while the
power is switched on again. The button must be held until LED
gives a red ash.
Factory reset
Once the Danfoss Link™ SCM and all other
devices in the system have been registered
and the Danfoss Link™ CC is placed in its nal
position, perform a full network test (see
separate Danfoss Link™ CC manual).
Perform network test
Transmission test (optional)
Initiate a transmission test on the Danfoss Link™ SCM by pressing
and holding the install button for more than 2 seconds. If the test
is satisfactory the green LED will ash and a message is displayed
on the Danfoss Link™ CC. If the test fails the red LED will slow
ash continuously.
GB
6VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
The away temperature can only be set on the Danfoss Link™ CC,
default setting is 15° C.
A SIM-card for the Danfoss Link™ Mobile Phone Butler is not
included. Before inserting the SIM-card please remember to dis-
able the PIN-code.
System test
After installation it is recommended to perform a
system test by texting (0000#0) to the Danfoss Link™
MPB in order to set the Danfoss Link™system to AWAY
mode (OFF).
On the Danfoss Link™ MPB and the SCM the AWAY mode is
indicated by a red LED. On the Danfoss Link™ CC the AWAY mode
is indicated by the suitcase icon.
After 10 minutes the AWAY mode screen will be replaced by the
Standby screen for security reasons.
Send another text message (0000#1) to revert the system to
the HOME mode (ON). The LED turns green and the AWAY icon
disappears. See the Danfoss Link™ MPB User Manual for further
information.
Smartphone app
For Android phones and iPhones you can download the Danfoss
ButlerApp for easy communication with the Danfoss Link™ MPB.
Other ON / OFF devices like sensors, manual switches, etc.
can also be used and connected to the SCM for turning
AWAY mode ON / OFF in the Danfoss Link™ system. The
ON / OFF device must be connected to the SCM via its NC and
COM slots.
Getting started with Danfoss Link™ SCM
7
VIFZT102 © Danfoss 03/2013
Installation Guide Danfoss Link™ SCM
Technical specications
Operating voltage Danfoss Link™ SCM 8 - 32 VDC
Operating voltage (Net adapter) 220 - 240 V~, 50 Hz
Standby consumption 0.9 W
Ambient temperature 0˚ to +45˚C
Transmission frequency 868.42 MHz
Transmission range in normal
buildings Up to 30 m
Transmission power Max. 1 mW
Pollution degree 2
Ball pressure test temperature 75˚C
Software classication Class A
IP class 20
Dimensions 80 × 80 × 30 mm
Disposal instructions
GB
013R9559 VIFZT15X © Danfoss 01/2013
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone: +45 7488 8000
Fax: +45 7488 8100
Email: heating.solutions@danfoss.com
www.heating.danfoss.com
Inhaltsverzeichnis
Andere Danfoss Steuereinheit Handbücher
Danfoss
Danfoss 38E Bedienungsanleitung
Danfoss
Danfoss TUA Bedienungsanleitung
Danfoss
Danfoss MCO 101 Bedienungsanleitung
Danfoss
Danfoss MSV-C Bedienungsanleitung
Danfoss
Danfoss AFQM Bedienungsanleitung
Danfoss
Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung
Danfoss
Danfoss PVG 32 Handbuch
Danfoss
Danfoss KP 15 Bedienungsanleitung
Danfoss
Danfoss RLV-X Bedienungsanleitung
Danfoss
Danfoss PVG 32 Handbuch
Danfoss
Danfoss Pilot-controlled PCVQ Bedienungsanleitung
Danfoss
Danfoss 176F3417 Bedienungsanleitung
Danfoss
Danfoss PM3 Bedienungs- und Wartungsanleitung
Danfoss
Danfoss EV220BW 15-50 Bedienungsanleitung
Danfoss
Danfoss OSPE Bedienungsanleitung
Danfoss
Danfoss EV250B NC Installationsanleitung
Danfoss
Danfoss AVTB Bedienungsanleitung
Danfoss
Danfoss TWA-Z Gen. 2011 Bedienungsanleitung
Danfoss
Danfoss EV251B Installationsanleitung
Danfoss
Danfoss ASV-PV Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
