Danfoss VACON 20 X Bedienungsanleitung

Vacon 20 X - Simple operator panel vacon • 1

Service support: find your nearest Vacon service center at www.vacon.com 1

1. VACON 20 X - SIMPLE OPERATOR PANEL

1.1 Mounting instructions

Document code: DPD01577A

1.1.1 QDSH Simple operator panel kit

Figure 1. The Simple operator panel option spare kit (MU2 example) .

Frame

size Description and type code Item Quantity

MU2 MU2 QDSH option spare kit

60S01208

Main switch 40A NLT40 and operator

panel assembly 1

MU2 cover for main switch 1

M4x14 screw 2

M5x23 screws 4

MU3 MU3 QDSH option spare kit

60S01209

Main switch 40A NLT40 and operator

panel assembly 1

MU3 cover for main switch 1

M4x14 screw 2

M5x23 screws 6

Table 1. Simple operator panel kit content.

vacon • 2 Vacon 20 X - Simple operator panel

1.1.2 Installation

Figure 2. Cover open.

1• Remove the cover from the drive. See the Figure 2.

2• Open only the inlet holes where you need to run the cables. Cables pass

through this inlet hole.

3• Connect the supply cable to the Mains switch passing through the cable gland

from the bottom side (use the cable gland for sealing the cable to the drive)

and then through the terminal box as shown in the figure below.

4• Place the Simple Operator panel assembly with the cables inside the drive and

fix it with its screws.

5• Connect the cables from the Mains switch to the line terminals. The cables

have to be connected to the terminals L1, L2 and L3.

6• Fix the cables with the cable clamp.

Vacon 20 X - Simple operator panel vacon • 3

Service support: find your nearest Vacon service center at www.vacon.com 1

Figure 3. Simple operator panel connected.

7• Connect the GROUND wire to the proper terminal (see the yellow-green cable

on Figure 3.

8• Connect the cables from the potentiometer and from the selector to the I/O

control terminals. The cables have to be connected to the I/O terminals as

shown in the Figure 3 and in the Table 2.

9• RED, BLUE and BLACK wires are signals from the potentiomenter.

10 • YELLOW, WHITE and GREY wires are signal from the selector switch.

vacon • 4 Vacon 20 X - Simple operator panel

Table 2. Control I/O terminal signal connections to the simple operator panel.

Standard I/O terminals

Terminal Signal

ARS485_A Serial bus, negative

BRS485_B Serial bus, positive

1+10 Vref Reference output

2AI1+ Analogue input,

voltage or current

3GND I/O signal ground

624Vout 24V aux. voltage

7DIN COM Digital inputs com-

mon

8DI1 Digital input 1

9DI2 Digital input 2

10 DI3 Digital input 3

4AI2+ Analogue input,

voltage or current

5GND I/O signal ground

13 DO1- Digital output 1 com-

mon

14 DI4 Digital input 4

15 DI5 Digital input 5

16 DI6 Digital input 6

18 AO1+ Analogue signal

(+output)

20 DO1+ Digital output 1

Function Description Wire colors Terminal

Potentiomenter

10V reference output RED wire 1

AI1+ BLUE wire 2

AI1- BLACK wire 3

Switch selector

24V auxiliary voltage YELLOW wire 6

digital input DI1 WHITE wire 8

digital input DI2 GREY wire 9

Table 3. Simple operator panel connection description.

11 • Mount the plastic cover onto the drive with its screws and the HMI cap: the

installation process has been completed.

YELLOW WIRE

WHITE WIRE

GREY WIRE

RED WIRE

BLUE WIRE

BLACK WIRE

Andere Danfoss Gleichstromantrieb Handbücher

Danfoss

Danfoss VLT AutomationDrive FC 360 Bedienungsanleitung

Danfoss

Danfoss VLT FC Series Bedienungsanleitung

Danfoss

Danfoss VLT HVAC FC 100 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Drive Metasys N2 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 200 Bedienungsanleitung

Danfoss

Danfoss VLT 6000 HVAC Profibus Bedienungsanleitung

Danfoss

Danfoss VLT series Bedienungsanleitung

Danfoss

Danfoss FC 300 Interbus Bedienungsanleitung

Danfoss

Danfoss VLT Micro Drive PK18 Leitfaden

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss FC 300 Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 360 Bedienungsanleitung

Danfoss

Danfoss FC 300 Leitfaden

Danfoss

Danfoss VLT AutomationDrive FC 301 Betriebsanleitung

Danfoss

Danfoss VLT 5000 Series Bedienungsanleitung

Danfoss

Danfoss VLT CANopen MCA 105 Betriebsanleitung

Danfoss

Danfoss VLT Betriebsanleitung

Danfoss

Danfoss vlt fcd 302 Leitfaden

Danfoss

Danfoss vlt aqua Bedienungsanleitung

Danfoss

Danfoss VLT 6000 HVAC Series Leitfaden

Danfoss

Danfoss VACON OPTEA Bedienungsanleitung

Danfoss

Danfoss Native BACnet VLT HVAC Drive Bedienungsanleitung

Danfoss

Danfoss VLT 4000 ME Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive EZ FC 321 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch