Danfoss VLT CDS 803 Bedienungsanleitung

MAKING MODERN LIVING POSSIBLE

Quick Guide

VLT®Compressor Drive CDS 803

vlt-drives.danfoss.com

Contents

1 Quick Guide 2

1.1 Safety 2

1.1.1 Warnings 2

1.1.2 Safety Instructions 2

1.2 Introduction 2

1.2.1 Available Literature 2

1.2.2 Approvals 3

1.2.3 IT Mains 3

1.2.4 Avoid Unintended Start 3

1.3 Installation 3

1.3.1 Before Starting Repair Work 3

1.3.2 Enclosure Types 3

1.3.3 Side-by-side Installation 4

1.3.4 Electrical Installation in General 5

1.3.5 Connecting to Mains and Compressor 5

1.3.6 Fuses 7

1.3.7 EMC-Correct Electrical Installation 8

1.3.8 Control Terminals 9

1.3.9 Electrical Overview 10

1.4 Programming 11

1.4.1 Local Control Panel (LCP) 11

1.4.2 Main Menu Structure 20

1.5 Acoustic Noise or Vibration 22

1.6 Warnings and Alarms 22

1.7 General Specications 23

1.7.1 Mains Supply 3x200–240 V AC 23

1.7.2 Mains Supply 3x380–480 V AC 24

1.7.3 EMC Test Results 25

1.8 Special Conditions 28

1.8.1 Derating for Ambient Temperature and Switching Frequency 28

1.9 Options for VLT®Compressor Drive CDS 803 28

Contents Quick Guide

1 Quick Guide

1.1 Safety

1.1.1 Warnings

WARNING

HIGH-VOLTAGE WARNING

The voltage of the frequency converter is dangerous

whenever it is connected to mains. Incorrect installation

of the compressor or frequency converter may cause

death, serious injury, or equipment damage. To avoid

death, serious injury, or equipment damage:

•Comply with the instruction in this manual as

well as local and national rules and safety

regulations.

WARNING

DISCHARGE TIME!

Frequency converters contain DC-link capacitors that can

remain charged even when the frequency converter is

not powered. To avoid electrical hazards, disconnect AC

mains, any permanent magnet type compressors, and

any remote DC-link power supplies, including battery

back-ups, UPS, and DC-link connections to other

frequency converters. Wait for the capacitors to fully

discharge before performing any service or repair work.

The waiting time is listed in Table 1.1. Failure to wait the

specied time after power has been removed before

doing service or repair could result in death or serious

injury.

Voltage [V] Cooling capacity [TR] Minimum waiting time

(minutes)

3x200 4–6.5 15

3x400 4–5 4

3x400 6.5 15

Table 1.1 Discharge Time

CAUTION

Leakage Current

The ground leakage current from the frequency

converter exceeds 3.5 mA. According to IEC 61800-5-1 a

reinforced protective earth connection must be ensured

with a minimum 10 mm2Cu or an extra PE wire with the

same cable cross-section as the mains wiring. Terminate

the PE connection separately.

Residual Current Device

This product can cause a DC current in the protective

conductor. Where a residual current device (RCD) is used

for extra protection, only an RCD of Type B (time

delayed) shall be used on the supply side of this

product. See also Danfoss Application Note on RCD.

Protective earthing of the frequency converter and the

use of RCDs must always follow national and local

regulations.

NOTICE

INSTALLATION AT HIGH ALTITUDES

For altitudes above 2000 m, contact Danfoss regarding

PELV.

1.1.2 Safety Instructions

•Make sure that the frequency converter is

properly connected to ground.

•Do not remove mains connections, compressor

connections, or other power connections while

the frequency converter is connected to power.

•Protect users against supply voltage.

•Protect the compressor against overloading

according to national and local regulations.

•The ground leakage current exceeds 3.5 mA.

•The [O/Reset] key is not a safety switch. It does

not disconnect the frequency converter from

mains.

1.2 Introduction

1.2.1 Available Literature

This quick guide contains basic information necessary for

installing and running the frequency converter. Supple-

mentary publications and manuals are available from

Danfoss. See www.danfoss.com/BusinessAreas/DrivesSo-

lutions/ Documentations/VLT+Technical+Documentation.htm

for listings.

Quick Guide VLT®Compressor Drive CDS 803

1.2.2 Approvals

Certication IP20

EC Declaration of

Conformity ✓

UL Listed ✓

C-tick ✓

Table 1.2 Approvals

The frequency converter complies with UL 508C thermal

memory retention requirements. For more information,

refer to the section Motor Thermal Protection in the

product-specic design guide.

1.2.3 IT Mains

CAUTION

IT MAINS

Installation on isolated mains source, that is, IT mains.

Maximum supply voltage allowed when connected to

mains: 440 V (3x380–480 V units).

Open the RFI switch by removing the screw on the side of

the frequency converter when at IT grid.

130BB612.10

1 RFI switch

Illustration 1.1 IP20

CAUTION

If reinserted, only use M3x12 screw.

1.2.4 Avoid Unintended Start

While the frequency converter is connected to mains, the

compressor can be started/stopped using digital

commands, bus commands, references or via the LCP.

•Disconnect the frequency converter from mains

whenever personal safety considerations make it

necessary to avoid unintended start of any

compressors.

•To avoid unintended start, always press [O/

Reset] before changing parameters.

Equipment containing electrical components

must not be disposed of together with domestic

waste.

It must be separately collected with electrical

and electronic waste according to local and

currently valid legislation.

1.3 Installation

1.3.1 Before Starting Repair Work

1. Disconnect from mains (and external DC supply, if

present).

2. Wait as stated in Table 1.1 for discharge of the

DC-link.

3. Remove the compressor cable.

1.3.2 Enclosure Types

Cooling capacity 400 V IP20 enclosure

4 TR/VZH028 H3

5 TR/VZH035 H3

6.5 TR/VZH044 H4

Table 1.3 H3–H4, 400 V

Cooling capacity 200 V IP20 enclosure

4 TR/VZH028 H4

5 TR/VZH035 H4

6.5 TR/VZH044 H5

Table 1.4 H4–H5, 200 V

Quick Guide Quick Guide

1.3.3 Side-by-side Installation

The frequency converter can be mounted side-by-side and requires the clearance above and below for cooling.

Enclosure IP class Clearance above/below [mm/(in)]

H3 IP20 100/(4)

H4 IP20 100/(4)

H5 IP20 100/(4)

Table 1.5 Clearance

NOTICE

With IP21/NEMA Type1 option kit mounted, a distance of 50 mm (2 in) between the units is required.

NOTICE

The illustration in Table 1.6 is with LCP, but all dimensions are the same without LCP.

D

130BB614.10

130BC246.10

Enclosure Height [mm/(in)] Width [mm/(in)] Depth

[mm/

(in)]

Mounting hole [mm/(in)] Maximum

weight

Enclosure IP class A A1) a B b C d e f [kg/(lb)]

H3 IP20 255

(10.0)

329

(13.0)

240

(9.4)

100

(3.9)

(2.9)

206

(8.1)

(0.4)

5.5

(0.2)

8.1

(0.3)

4.5

(9.9)

H4 IP20 296

(11.7)

359

(14.1)

275

(10.8)

135

(5.3)

105

(4.1)

241

(9.5)

12.6

(0.5)

(0.3)

8.4

(0.3)

7.9

(17.4)

H5 IP20 334

(13.1)

402

(15.8)

314

(12.4)

150

(5.9)

120

(4.7)

255

(10.0)

12.6

(0.5)

(0.3)

8.5

(0.3)

9.5

(20.9)

Table 1.6 Dimensions

1) Including decoupling plate

The dimensions are only for the physical units, but when installing in an application, it is necessary to add space for free air

passage both above and below the units. The amount of space for free air passage is listed in Table 1.5.

Quick Guide VLT®Compressor Drive CDS 803

1.3.4 Electrical Installation in General

All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper

conductors required, (75 °C/167 °F) recommended.

Enclosure Torque [Nm(in-lb)]

Enclosure IP class Line Compressor

connection

DC connection Control

terminals

Ground Relay

H3 IP20 1.4 (12.4) 0.8 (7.1) 0.8 (7.1) 0.5 (4.4) 0.8 (7.1) 0.5 (4.4)

H4 IP20 1.2 (10.6) 1.2 (10.6) 1.2 (10.6) 0.5 (4.4) 0.8 (7.1) 0.5 (4.4)

H5 IP20 1.2 (10.6) 1.2 (10.6) 1.2 (10.6) 0.5 (4.4) 0.8 (7.1) 0.5 (4.4)

Table 1.7 Enclosure H3–H5

1.3.5 Connecting to Mains and Compressor

The frequency converter is designed to operate Danfoss

VZH Compressors. For maximum cross-section on wires, see

chapter 1.7 General Specications.

•To comply with EMC emission specications, use

a shielded/armored compressor cable and

connect this cable to both the decoupling plate

and the compressor metal.

•Keep compressor cable as short as possible to

reduce the noise level and leakage currents.

•For further details on mounting of the decoupling

plate, see VLT

Compressor Drive CDS 803

Decoupling Plate Installation Instructions.

•Also see EMC-Correct Installation in the VLT

Compressor Drive CDS 803 Design Guide.

1. Mount the ground wires to ground terminal.

2. Connect compressor to terminals U, V, and W, see

Table 1.8.

U T1

V T2

W T3

Table 1.8 Connection of Compressor to Terminals

3. Mount mains supply to terminals L1, L2, and L3

and tighten.

130BB634.10

Motor

UVW-DC+DC

MAINS

1 Line

2 Ground

3 Compressor

4 Relays

Illustration 1.2 H3–H5 Enclosure

IP20 200–240 V 4–6.5 tons

IP20 380–480 V 4–6.5 tons

Quick Guide Quick Guide

-DC+DC

BR- BR+ U V W

M A I N S

RELAY 1 RELAY 2

- LC +

130BA261.10

Illustration 1.3 Mount the 2 screws in the mounting plate,

slide it into place and tighten fully.

MOTOR

U V W

130BT302.12

Illustration 1.4 H3–H5 Enclosure

130BA262.10

I N S

+DC

BR- BR+ UVW

RELAY 1 RELAY 2

Illustration 1.5 When mounting cables, rst mount and tighten

the ground cable.

130BA263.10

MAINS

+DC

BR- BR+ UVW

91 92 93

L1 L2 L3

RELAY 1 RELAY 2

Illustration 1.6 Mount mains plug and tighten wires.

Quick Guide VLT®Compressor Drive CDS 803

+DC

BR- BR+ UVW

MAINS

L1 L2 L3

91 92 93

RELAY 1 RELAY 2

- LC -

130BA264.10

Illustration 1.7 Tighten support bracket on mains wires.

1.3.6 Fuses

Branch circuit protection

To protect the installation against electrical and re hazard, all branch circuits in an installation, switch gear, machines, and

so on, must be short circuit and overcurrent protected according to national and local regulations.

Short-circuit protection

Danfoss recommends using the fuses listed in Table 1.9 to protect service personnel or equipment if there is an internal

failure in the unit or a short circuit on the DC-link. The frequency converter provides full short-circuit protection if there is a

short circuit on the compressor.

Overcurrent protection

To avoid overheating of the cables in the installation, provide overload protection. Overcurrent protection must always be

carried out according to local and national regulations. Design circuit breakers and fuses for protection in a circuit capable

of supplying a maximum of 100000 Arms (symmetrical), 480 V maximum.

UL/Non UL compliance

To ensure compliance with UL or IEC 61800-5-1, use the fuses listed in Table 1.9.

NOTICE

In the event of malfunction, failure to follow the protection recommendation may result in damage to the frequency

converter.

Fuse

UL Non-UL

CDS 803 Bussmann

Type RK5

Bussmann

Type RK1

Bussmann

Type J

Bussmann

Type T

Maximum fuse

Type G

3x200–240 V IP20

4 TR/VZH028 FRS-R-50 KTN-R50 JKS-50 JJN-50 50

5 TR/VZH035 FRS-R-50 KTN-R50 JKS-50 JJN-50 50

6.5 TR/VZH044 FRS-R-80 KTN-R80 JKS-80 JJN-80 65

3x380–480 V IP20

4 TR/VZH028 FRS-R-25 KTS-R25 JKS-25 JJS-25 25

5 TR/VZH035 FRS-R-25 KTS-R25 JKS-25 JJS-25 25

6.5 TR/VZH044 FRS-R-50 KTS-R50 JKS-50 JJS-50 50

Table 1.9 Fuses

Quick Guide Quick Guide

1.3.7 EMC-Correct Electrical Installation

General points to be observed to ensure EMC-correct electrical installation.

•Use only screened/armoured motor cables and screened/armoured control cables.

•Connect the screen to ground at both ends.

•Avoid installation with twisted screen ends (pigtails), since this ruins the screening eect at high frequencies. Use

the cable clamps provided instead.

•Ensure the same potential between frequency converter and ground potential of the PLC.

•Use star washers and galvanically conductive installation plates.

Com.

Warn.

Alarm

Hand

On Reset Auto

Menu Status Quick

Menu Main

Minimum 16 mm2

equalizing cable

Control cables

All cable entries in

one side of panel

Earthing rail

Cable insula-

tion stripped

Output con-

tactor

Motor cable

Motor, 3 phases and

PLC Panel

Mains-supply

Minimum 200 mm

between control

cable, mains cable

and between mains

motor cable

PLC

protective earth

Reinforced protective earth

130BB761.11

Illustration 1.8 EMC-correct Electrical Installation

Quick Guide VLT®Compressor Drive CDS 803

Andere Handbücher für VLT CDS 803

Inhaltsverzeichnis

Andere Danfoss Gleichstromantrieb Handbücher

Danfoss

Danfoss VLT AutomationDrive Betriebsanleitung

Danfoss

Danfoss VLT HVAC Drive Metasys N2 Bedienungsanleitung

Danfoss

Danfoss VLT Midi Drive FC 280 Betriebsanleitung

Danfoss

Danfoss VLT series Leitfaden

Danfoss

Danfoss Native BACnet VLT HVAC Drive Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 360 Bedienungsanleitung

Danfoss

Danfoss FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss VLT DriveMotor FCP 106 Bedienungsanleitung

Danfoss

Danfoss VLT CDS302 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Leitfaden

Danfoss

Danfoss VLT AutomationDrive FC 301 Betriebsanleitung

Danfoss

Danfoss VLT 6000 HVAC Series Leitfaden

Danfoss

Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT Midi Drive FC 280 Betriebsanleitung

Danfoss

Danfoss VLT FC Series Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung

Danfoss

Danfoss FC 300 Betriebsanleitung

Danfoss

Danfoss FC 300 Leitfaden

Danfoss

Danfoss VLT DriveMotor FCP 106 Bedienungsanleitung

Danfoss

Danfoss VLT OneGearDrive Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Leitfaden

Danfoss

Danfoss AME 23 Bedienungsanleitung

Danfoss

Danfoss FC 302 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch