Danfoss HG7 Bedienungsanleitung
AX450533577373en-000201
HG88e
HG7
Repair instruction electric motor
Service guide
2 | AX450533577373en-000201 © Danfoss | Climate Solutions | 2023.07
Contents
1 Liability and Warranty......................................................................................................................2
2 Additional Safety Information............................................................................................................2
3 Disassembly .......................................................................................................................................4
4 Assembly ............................................................................................................................................8
1 Liability and Warranty
Liability and the manufacturer‘s warranty are excluded if
• Alterations and functional modications have been carried out,
• no original replacement parts have been used.
2 Safety Information
Target group for this repair information
¾Work on the compressor may only be carried out by persons whose technical training, skills and
experience along with their knowledge of pertinent regulations and documentation means that they
are capable of assessing the work to be carried out and detecting any possible dangers.
¾A specialist can mean a refrigeration technician for example. Note that electrical work may only be
carried our by a qualied electrician. Alternatively, on a country-specic basis, persons who have
undergone electrotechnical instruction and who have proof of their qualication are also permitted
to carry out the work.
• DANGER! This symbol refers to instructions for avoiding direct severe
dangers to persons or plant by electrical current.
• DANGER! This symbol refers to instructions for avoiding direct severe dangers
to persons.
• WARNING! This symbol is used to indicate that inaccurate compliance or
total failure to comply with the instructions could cause injury to persons or
damage to the compressor or refrigerating machine.
• This symbol is used to indicate that parts with refrigeration oils (for oil types see
compressor name plate) should be moistened prior to installing.
• This symbol indicates the permitted tightening torque for the screw.
60 Nm
© Danfoss | Climate Solutions | 2023.07 AX450533577373en-000201 | 3
Safety Information
Important prerequisites
DANGER
Risk of electric shock.
XBefore you carry out any repair work, disconnect the compressor from the electricity network.
XTurn the main switch to „O“ (OFF).
XSecure the main switch against an unauthorised restart.
WARNING
The heavy weight of the compressor can be potentially dangerous.
Use all the seals included in the kit.
4 | AX450533577373en-000201 © Danfoss | Climate Solutions | 2023.07
Disassembly
3 Disassembly
WARNING
Ensure that the compressor is depressurised before starting work.
3.1 Draining the oil
NOTE
Do not dispose of oil in domestic waste.
XDispose of the old oil in accordance with the environmental regulations and observe national regulations
© Danfoss | Climate Solutions | 2023.07 AX450533577373en-000201 | 5
Disassembly
3.2 Disconnecting the electrical connections
XDo not damage any cables and components.
Damaged parts must be repaired or replaced immediately.
HG7/HGZ7
¾Remove the terminal box (4 hexagon head screws M6,
AF10).
¾Remove the terminal board (10 hexagon head screws
M10x35, AF17).
¾Remove the electrical lines from the underside of the
terminal board.
¾Remove the terminal box (4 hexagon head screws M8,
AF13).
¾Remove the socket head screws (10x M10x20, AF8) from
the terminal board.
¾The terminal board must be pushed off the compressor
housing.
To do so, completely remove the nuts (M6, AF10 and M8,
AF13) from the threaded pins of the earthing connector.
Now rotate the threaded pins (socket head AF3 and AF4)
further in order to push the terminal board out of the
compressor housing. The silicon bonded joint is dest-
royed in the process!
¾Remove the electrical lines from the underside of the
terminal board.
HG8/HG88e
6 | AX450533577373en-000201 © Danfoss | Climate Solutions | 2023.07
3.3 Remove housing cover
WARNING
The heavy weight of the compressor and parts can potentially be dangerous; risk of falling,
danger of crushing.
XATTENTION! The residual oil ows out when the case cover is removed.
Lay an absorbent material under the area and dispose of it in accordance with the environmental regulations.
Disassembly
© Danfoss | Climate Solutions | 2023.07 AX450533577373en-000201 | 7
3.4 Removing the stator
WARNING
The heavy weight of the stator can potentially be dangerous; risk of falling, danger of crushing.
XUse a suitable hoist for the removal.
XTake the measures required to safely remove the stator by placing a square of the correct height at the
open end of the motor housing. Prevent inadvertent rolling of the removed stator.
¾Carefully pull the stator out of the compressor housing and pay attention to the cable!
¾Remove the feather key from the compressor housing.
¾Remove both stator screws (M8x20). ¾Remove both stator screws (M8x10, M8x20).
HG7/HGZ7 HG8/HG88e
max.
75kg
Disassembly
8 | AX450533577373en-000201 © Danfoss | Climate Solutions | 2023.07
Assembly
4 Assembly
We recommend cleaning the inside of the case before the installation.
There must not be any particles and dirt in the compressor.
To assemble, reverse the order of the steps. Note any particular features such as observance of different torques.
4.1 Connecting the stator to the motor housing
WARNING
The heavy weight of the stator can potentially be dangerous; risk of falling, danger of crushing.
XUse a suitable hoist for the removal.
XNote the direction of the feather key — stator.
You must align the parts in order to install them.
HG7/HG8/HG88e
XDo not damage any cables and components. Push the stator with the cables leading into the motor housing as far
as it will go. At the same time, carefully pull the cables upwards through the terminal board opening.
¾Align the stator so that the feather key can be pushed in the the groove ush with the housing surface.
max.
75kg
© Danfoss | Climate Solutions | 2023.07 AX450533577373en-000201 | 9
Assembly
HGZ7/1620+1860
XDo not damage any cables or component parts. Push the stator with the cables leading into the motor housing to a
depth of 13.5 mm. At the same time, carefully pull the cables upwards through the terminal board opening.
¾Align the stator such that the feather key can be pushed in the the groove on the motor housing ush with the stator.
¾Fix the feather key and stator in this position using the new stator screws, as described on page 10.
max.
75kg
13,5 mm
Motor housing
Feather key
Stator
10 | AX450533577373en-000201 © Danfoss | Climate Solutions | 2023.07
¾Screw in the new stator screws. The hardening time of the thread coating is 6 hours. The stator screw must
only be used once.
HG8/HG88e
AA
BB
A - A
B - B
Threaded pin presses
on stator assembly
Threaded pin presses
on feather key
C - C
C C
10 Nm 10 Nm
HG7/HGZ7
Assembly
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Danfoss Motor Handbücher
Danfoss
Danfoss K Frame Series Bedienungsanleitung
Danfoss
Danfoss MP1 Bedienungsanleitung
Danfoss
Danfoss G 4500 Bedienungsanleitung
Danfoss
Danfoss H1B 060 Bedienungsanleitung
Danfoss
Danfoss EM-PMI240 Bedienungsanleitung
Danfoss
Danfoss EM-PMI540-T1500 Bedienungsanleitung
Danfoss
Danfoss VLT DriveMotor FCP 106 Bedienungsanleitung
Danfoss
Danfoss VLT AutomationDrive FC 300 Series Bedienungsanleitung
Danfoss
Danfoss MAH Series Bedienungsanleitung
Danfoss
Danfoss VLT OneGearDrive Bedienungsanleitung
Danfoss
Danfoss EM-PMI540-T2000 Bedienungsanleitung
Danfoss
Danfoss EM-PMI540-T2000 Bedienungsanleitung
Danfoss
Danfoss EM-PMI300-T310 Bedienungsanleitung
Danfoss
Danfoss VLT OneGearDrive ExtensionBox Bedienungsanleitung
Danfoss
Danfoss VLT DriveMotor FCP 106 Betriebsanleitung
Danfoss
Danfoss 51 Series Handbuch
Danfoss
Danfoss EM-PMI375-T200 Bedienungsanleitung
Danfoss
Danfoss VLT OneGearDrive Bedienungsanleitung
Danfoss
Danfoss Series 20 Einrichtungshandbuch
Danfoss
Danfoss EM-PMI540-1500 Bedienungsanleitung
