Danfoss Ikargo2 Bedienungsanleitung

User Manual

Ikargo2 Transmitter

Remote Control

www.danfoss.com

Revision history Table of revisions

Date Changed Rev

February 2021 Changed name Ikargo10 to Ikargo2 0201

July 2019 Rebranded to Danfoss. 0101

User Manual

Ikargo2 Transmitter

2 | ©Danfoss | February 2021 BC312438493831en-000201

Safety instructions General safety....................................................................................................................................................................................4

Safety warnings.................................................................................................................................................................................4

Technical description Ikargo2 Dimensions.........................................................................................................................................................................5

Ikargo2 Start-up................................................................................................................................................................................ 6

Maintenance Ikargo2 Maintenance Recommendations............................................................................................................................... 8

Troubleshooting............................................................................................................................................................................... 8

Charger and battery BC70K and BT11K specifications.................................................................................................................................................9

BC70K Battery Charger Set-up.....................................................................................................................................................9

BC70K Charger LEDs Status .......................................................................................................................................................10

Battery Charging Recommendations..................................................................................................................................... 10

BC70K Battery Charger Dimensions........................................................................................................................................11

User Manual

Ikargo2 Transmitter

Contents

©Danfoss | February 2021 BC312438493831en-000201 | 3

Ikargo2 General Safety

The following safety instructions must be read carefully to install and use the product properly, and to

keep it in perfect working condition, and to reduce the risk of misuse.

•Strictly adhere to the installation instructions contained in this document.

•Make sure that professional and competent personnel carry out the installation.

•Ensure that all site and prevailing safety regulations are fully respected.

•Make sure that this document is permanently available to the operator and maintenance personnel.

•Keep the transmitter out of reach of non-authorized personnel.

•Remove the transmission key when the set is not in use.

•Check each working day the STOP button and other safety measures. When in doubt, press the STOP

button.

•Whenever several sets have been installed, make sure the transmitter is the right one. Identify the

machine controlled on the label for this purpose on the transmitter or by using the display (in case it

has one).

•Service the equipment periodically.

•When carrying out repairs, use spare parts supplied by Danfoss only.

Warning

Potential damage to the operator or the product. Do not use this product on machines in potentially

explosive atmospheres unless the model is ATEX/RATEX certified to work in such conditions.

Ikargo2 Safety Quick Guide

Follow the Safety Quick Guidelines below to reduce risk of injury to the operator or the product.

Changes or modifications not approved by Danfoss can void the user's authority to operate this product.

Remove the transmission key only when the

set is not in use or to deny the access.

When in doubt, press the STOP button. Make sure the transmitter works with the

machine to be handled.

After use set the contact key and the STOP

button.

Do not use the set when visibility is limited. Avoid knocking or dropping the set.

User Manual

Ikargo2 Transmitter

Safety instructions

4 | ©Danfoss | February 2021 BC312438493831en-000201

Ikargo2 Dimensions

Dimensions (mm)

1. Range limiter

2. RGB display

3. Status LED

4. Maneuver push button

5. Multi-key/START

6. STOP button

7. Movement pictogram housing

8. BT11K battery housing

9. Extractable EEPROM housing

User Manual

Ikargo2 Transmitter

Technical description

©Danfoss | February 2021 BC312438493831en-000201 | 5

Ikargo2 Start-up

In order to turn the transmitter on - OPERATION mode, follow the steps bellow:

1. Insert the charged BT11K battery model in the transmitter and ensure the EEPROM module is in place.

The battery must be charged according to the charger manual's instruction.

2. Turn the multi-key from the position 0to the 1position.

The multi-key cannot be removed while in the 1position.

3. Push and pull out the stop button.

The LED will blink in blue-green colors and the battery level will appear in the display. It is

recommended to introduce the machine identifier (example: EOT crane number).

User Manual

Ikargo2 Transmitter

Technical description

6 | ©Danfoss | February 2021 BC312438493831en-000201

4. Press START with the multi-key until the radio link is performed.

The LED color will turn green to indicate that the transmitter and receiver link is confirmed.

5. After confirmation, press the maneuver buttons to verify corresponding movements.

User Manual

Ikargo2 Transmitter

Technical description

©Danfoss | February 2021 BC312438493831en-000201 | 7

Ikargo2 Maintenance Recommendations

This product is designed for use in an industrial environment that may shorten the product's lifespan. Use

these recommendations to maximize the lifespan of the product.

•Use the hook/belt provided with the transmitter to prevent the transmitter from falling

•Do not clean the transmitter with solvents or pressurized water; use a damp cloth or soft brush for

cleaning

•If the push buttons show signs of deterioration, contact the Authorized Technical Service for repair

•Check if the battery contacts are correct, otherwise replace them.

•Be sure to recharge or replace battery regularly

Maintenance tips quick reference

Ikargo2 Troubleshooting

The transmitter has status monitoring LED's which help identify irregularities. The most common signals

are contained in the table below:

LED color | Frequency Pulse Frequency Description Action

Green | continuous The transmitter works properly. Operation

mode is OK. No action needed.

Green | pulses STANDBY mode. If transmitter is 4 minutes

ON and no action has been taken. Press START to return to operation mode.

Red | slow pulses Low battery signal. In 5 minutes you need to replace with full

battery.

Red | fast pulses EEPROM module missing or corrupted. Check EEPROM module or reprogram if

necessary.

Red | double pulses A maneuver is activated at transmitter start up

process; may indicate hardware damage if no

order is active.

Release maneuver or replace transmitter if

necessary.

Red | continuous General hardware failure or damage. Replace transmitter

User Manual

Ikargo2 Transmitter

Maintenance

8 | ©Danfoss | February 2021 BC312438493831en-000201

BC70K and BT11K specifications

BC70K battery charger

Specification Value

AC power supply 110 – 230 V, 50/60 Hz, ± 10%, automatic switching

DC power supply, nominal 12 – 24 V

BT11K battery

Specification Value

Voltage 3.7 V

Capacity 1130 mAh Li-Ion

Charging temperature 0°C to 45°C

Discharge temperature -20°C to 60°C

Charging mode Fast (<2.5 h) and intelligent

Weight 23 g

BC70K Battery Charger Set-up

The battery charger has two charging compartments that can simultaneously charge two BT11K

batteries. Use the information below to set up the BC70K battery charger.

1. Connect the charger to a power source using the cable provided.

The red LED will switch on if the charger is properly connected.

2. Place the batteries in the charger.

3. Optional: If charging two batteries, wait at least five seconds before inserting the second battery into

the compartment.

Warning

Possible damage to battery.

Be sure to charge batteries in environments with temperatures over 0°C.

User Manual

Ikargo2 Transmitter

Charger and battery

©Danfoss | February 2021 BC312438493831en-000201 | 9

BC70K Charger LEDs Status

The BC70K charger has a LED for each compartment (BAT 1 and BAT 2) and a common indicator

(POWER).

LED color / frequency Description

Green LED / pulsing (BAT 1, BAT 2) The battery is being charged

Green LED / continuous (BAT 1, BAT 2) The battery is completely charged

Red LED / pulsing or continuous (BAT 1, BAT 2) The battery charger fault

Red LED / continuous (POWER) The charger is properly connected to power source

Battery Charging Recommendations

The battery lifespan is estimated to 500 recharging cycles and is largely dependent on the conditions of

use. To maximize the lifespan of the batteries and battery charger, follow these recommendations:

•Do not recharge the battery until it is completely flat, as shown with red LED slow pulse on the

transmitter

•Always charge the batteries at temperatures between 0° and 45°C (the batteries will not become fully

charged at temperatures exceeding 45°C)

•Do not leave the battery charger or batteries in a direct sunlight

•Charge batteries at least once every six months

•Avoid short circuits between the battery contacts; do not carry charged batteries in toolboxes or next

to other metal objects (keys, coins, etc.)

•Always keep contacts clean

User Manual

Ikargo2 Transmitter

Charger and battery

10 | ©Danfoss | February 2021 BC312438493831en-000201

Inhaltsverzeichnis

Andere Danfoss Fernbedienung Handbücher

Danfoss

Danfoss CF-RC Bedienungsanleitung

Danfoss

Danfoss R06 Bedienungsanleitung

Danfoss

Danfoss IK2 Bedienungsanleitung

Danfoss

Danfoss TM70 Bedienungsanleitung

Danfoss

Danfoss MPCAN Bedienungsanleitung

Danfoss

Danfoss WS103 Bedienungsanleitung

Danfoss

Danfoss MP08A Bedienungsanleitung

Danfoss

Danfoss CF-RC Bedienungsanleitung

Danfoss

Danfoss CF-RC Bedienungsanleitung

Danfoss

Danfoss Ikompact Bedienungsanleitung

Danfoss

Danfoss SET3M Bedienungsanleitung

Danfoss

Danfoss FP975 Montageanleitung

Danfoss

Danfoss IKORE Bedienungsanleitung

Danfoss

Danfoss T70 1 HALL Bedienungsanleitung

Danfoss

Danfoss 102E7 Bedienungsanleitung

Danfoss

Danfoss 103E7 Montageanleitung

Danfoss

Danfoss IKP1000 Bedienungsanleitung

Danfoss

Danfoss IKORE B Bedienungsanleitung

Danfoss

Danfoss R13 F Bedienungsanleitung

Danfoss

Danfoss 175G9004 Bedienungsanleitung

Danfoss

Danfoss Ikompact Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung