Darfon DL-300 Bedienungsanleitung
INSTALLATION MANUAL
DL-300 DATA LOGGER
Rev. 01 ©2020 Darfon Electronics Corp. 2| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
TABLE OF CONTENTS
IMPORTANT INFORMATION .............................................................3
What You Need Before You Begin .................................................3
FCC Compliance ...............................................................3
PRODUCT OVERVIEW ..................................................................3
What’s in the Box ..............................................................3
Connections ..................................................................4
LED Definitions ................................................................4
MOUNTING THE DATA LOGGER..........................................................4
Location Requirements ..........................................................4
CONNECTING TO THE INVERTER ........................................................5
CONFIGURING FOR WIFI................................................................8
MONITORING PORTAL .................................................................12
Registering a new system .......................................................12
APPENDIX A: TECHNICAL SPECIFICATIONS ..............................................15
APPENDIX B: TROUBLESHOOTING......................................................16
Rev. 01 ©2020 Darfon Electronics Corp. 3| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
IMPORTANT INFORMATION
The DL-300 data logger is the hardware that connects Darfon hybrid inverters to the Darfon cloud monitoring system. Please read all
instructions before installing this data logger. And, store this installation manual where it can be accessed easily.
What You Need Before You Begin
■ Internet service
■ A computer with WiFi
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the
following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and the receiver.
■ Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
PRODUCT OVERVIEW
What’s in the Box
Parts Description Qty
1. DL-300 Data Logger
2. Wi-Fi Antenna
3. RS485 Cable
4. Power Adapter
5. RJ-45 Cable
6. USB Flash Drive
7. Din Rail
8. Din Rail Mount
9. Self-Tapping Screws
10. M3 Screws
11. Power Connector Adapter
1
1
1
1
1
1
1
2
2
4
1
Rev. 01 ©2020 Darfon Electronics Corp. 4| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
Connections
Port Description
ANT Attach the antenna for WiFi connection.
WAN Connect the RJ-45 cable for a LAN connection.
3G/4G Connect a 3G/4G dongle for a cellular connection.
DATA USB flash drive.
(T0) RS485 Connects to the hybrid inverter for two-way communication.
(T1) RS485 External RS485 sensor device reserved.
RESET Factory default reset button. Insert a pin and hold for 30 seconds.
LED Definitions
LED Activity Description
WAN ●●Solid
●●Flashing
●●Off
The LAN is connected.
Data is being transmitted or received.
No connection established.
WIFI ●●Solid
●●Flashing
●●Off
The WIFI is enabled.
Data is being transmitted or received.
WIFI is disabled.
DL PWR ●●Solid
●●Solid
●●Off
Power is on.
System initialization.
There is no Power.
(T0) RS485 ●●Solid
●●Solid
●●Off
A command is transmitted to the inverter(s).
A command is received from the inverter(s).
No commands are being transmitted or received.
(T1) RS485 ●●Solid
●●Solid
●●Off
A command is transmitted to the device(s).
A command is received from the device(s).
No commands are being transmitted or received.
MOUNTING THE DATA LOGGER
Location Requirements
■ The DL-300 has an IP20 rated enclosure, which means it must be installed indoors.
■ The RS485 cable is about 4’ long, so the data logger should be mounted no more than 3 feet away from the inverter.
■ The data logger requires an internet connection, be it wired, WiFi or cellular.
■ The data logger can be mounted to the wall, or elsewhere with the use of the din rail and din rail mounts.
Step 1. If the data logger cannot be secured to a stud in the wall, insert drywall anchors prior to installation.
Step 2. Place the data logger against the wall and secure with two screws.
Rev. 01 ©2020 Darfon Electronics Corp. 5| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
CONNECTING TO THE INVERTER
Step 1. Unlock Bypass switch. If there is a screw on the rocker
arm that keeps the Bypass off, remove it with a small
Philips screwdriver.
Step 2. Switch on Bypass, so your load runs from grid while the
inverter is turned off. Make sure the breakers are in the
correct position. Grid and Bypass are on. Load is off.
Step 3. Turn off the main switch that is located on the side of
the inverter.
Step 4. Insert the black wire of the RS485 cable into the first pin,
(T0) D-, and the red wire into the second pin, (T0) D+, of
the data logger. Then use a small flathead screwdriver to
tighten the screws.
Step 5. Open the door on the inverter and remove the dead front cover if needed (See inverter manual for instructions). Look inside and
on the top bulkhead panel you should find a green socket (with 4 pins) labeled “RS485 S”.
Rev. 01 ©2020 Darfon Electronics Corp. 6| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
Step 6. Connect the RS485 connector into the first two pins of
the port labeled “RS485 S” on the inverter. Push the
connector in hard so that it seats properly.
RS485 S RS485 M
Step 7. Insert the USB flash drive into the data logger.
Step 8. Internet Connection. There are three ways to establish an internet connection: LAN, WiFi or Cellular.
LAN Connection
Connect the ethernet cable to the
data logger and to the network/router.
WiFi Connection
Connect the antenna to the data logger.
Cellular Connection
Connect a non password protected
3G/4G dongle to the data logger.
Step 9. Connect the power adapter into the data logger and then to the power outlet.
Note: The power outlet needs to be a backed up so
the data logger will still work when there is no grid.
Rev. 01 ©2020 Darfon Electronics Corp. 7| Page
MIG300 MICRO INVERTER INSTALLATION MANUAL
Step 10. Turn the inverter on by the using Main Switch on the inverter. Wait for the inverter to boot up before going to the next step.
Step 11. Turn the load breaker back on.
Rev. 01 ©2020 Darfon Electronics Corp. 8| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
CONFIGURING FOR WIFI
Step 1. Connect the computer to the DL-300 through WiFi. The password is SBC700ap. The
network name will be “DL300_” followed by the last 6 characters of the WiFi MAC address.
The WiFi MAC address label is located on either the front or side of the DL-300.
Step 2. Open a web browser and go to “192.168.100.1”. If you are redirected to a warning page, click on “Advanced” and then “Proceed”.
If not, then go to the next step.
Note: The wording and appearance of the warning page will vary depending on which browser is used.
Step 3. Log in with username root and password SBC700pw.
Step 4. In the sidebar menu, click on “Network”.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00
Notes:
■ The data logger must have power and the antenna must be attached.
■ If power was just connected to the DL-300, it will take 1 minute before
the network appears on your computer.
Rev. 01 ©2020 Darfon Electronics Corp. 9| Page
INSTALLATION MANUAL DL-300 DATA LOGGER
Step 5. In the sidebar menu, click on “Interfaces”.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00
Step 6. Click “edit” in the “LAN” section.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Step 7. Change protocol from “DHCP client” to “Static address”.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Step 8. Click “Switch protocol”.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Step 9. Enter 192.168.10.1 into the IPv4 address and
255.255.255.0 in the IPv4 netmask.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on Unsaved Changes: 2
255.255.255.0
192.168.10.1
Step 10. Scroll down and click “Save & Apply”. Wait until you are
redirected back the network interfaces page.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Rev. 01 ©2020 Darfon Electronics Corp. 10 | Page
INSTALLATION MANUAL DL-300 DATA LOGGER
Step 11. Click “edit” in the “WIFI_AP” section.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Step 12. Scroll down to the “DHCP Server” section and check the
“Ignore interface” checkbox.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Step 13. Click “Save & Apply”, and wait until you are redirected
back the network interfaces page.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Step 14. In the sidebar menu, click on “Wireless”.
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Step 15. Click on “Scan” to search for available networks.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Step 16. Find your network and click on “Join Network”.
SBC700 | OpenWrt 18.06.2 r7676-cddd7b4c77 | Load: 0.00 0.00 0.00 | Auto Refresh: on
Powered by LuCI openwrt-18.06 branch (git-19.020.41695-6f6641d)
Inhaltsverzeichnis
Andere Darfon Datenlogger Handbücher
