DAS AUDIO INTEGRAL-WPM1 Bedienungsanleitung
INTEGRAL-WPM1
User manual
www.dasaudio.com
2INTEGRAL-WPM1 Manual
INTEGRAL
Overview
DAS Audio is a unique brand. We
create sound solutions for businesses,
always adapted to the different needs
of our clients.
The Integral Series is the heart and brain of our installation
solutions. It comprises of a series of devices that in addition
to feeding and processing the signal of our speakers,
allow an absolute control to our users, guaranteeing the
protection and quality of the equipment.
You are about to discover what it means to work with our
brand, and this is just the beginning. You will have access
to quality training materials on our website, where you will
discover specific business solutions and learn how to use
them: dasaudio.com/en/training/
This user manual is designed to guide you, swiftly and
smoothly, during the installation of our equipment, but
in case you have any questions or doubts, do not hesitate
to contact our technical support team by writing directly
to [email protected]om or, if you prefer, through our
website, contacting your nearest office at dasaudio.com/
contact
3INTEGRAL-WPM1 Manual
INTEGRAL
Description and features
INTEGRAL-WPM1 is a 2-channel wall-panel format audio
mixer. It includes one balanced XLR microphone input
(Phantom 12V can be activated with internal jumper) and
an unbalanced Stereo Line input (2 x RCA or 1x1/8” jack).
Each channel (mic and line) has its own independent level
control. The microphone´s signal can be prioritized over
the line signal by engaging the talk-over functionality
(internal jumper). It allows mixing these two signals
getting a balanced mono output that can be sent to
Matrix amplifiers, matrix or amplifiers.
• 2 channel mixer, wall-panel format
• Unbalanced Stereo Line input (2xRCA, 1x1/8” jack)
• Balanced Microphone input (XLR) with integrated
High Pass Filter
• Balanced mono signal output
• Independent volumecontrolforMICandLine channels
• Priority (Talk-over) function available (MIC over Line)
• Phantom power available for MIC channel
• External 12-24Vdc External PSU required, INTEGRAL-
PS12
• 86 x 86 mm electrical box included
4INTEGRAL-WPM1 Manual
INTEGRAL
Front panel
A
B
C
D
E
Balanced Microphone input XLR connector. Pin
assignments:
1or S = GND (Ground)
2or T = (+) Non inverted input
3or R = (-) Inverted input
Microphone´s level control. For minimum level rotate
completely to the left
Unbalanced Stereo Line input RCA connectors
Line´s level control. For minimum level rotate
completely to the left
3.5mm audio mini-jack input for connecting external
audio sources as tablets, phones, PCs etc. The mini-
jack input would be added to the unbalanced RCA
inputs
AB
E
CD
12
3
5INTEGRAL-WPM1 Manual
INTEGRAL
Rear panel
A
B
C
D
Audio Output Connector and Vdc in. The 6 pin
Euroblock type connector is used to connect the
analog audio cables and the Vdc voltage from the
external power supply. Pin assignments:
1V+ from the power supply
2V- from the power supply
3OUT + , Audio Signal, Pin 2 of an XLR connector
4OUT- , Audio Signal, Pin 3 of an XLR connector
5not used
6Earth
Link Jumper: used to connect EARTH and V- of the
Power Supply. Normally has to be connected to avoid
noise or hum.
PHT Jumper: When inserted the Phantom power will
be available at the XLR connector
TKO Jumper: Remove it to activate Talk Over
functionality of the Microphone´s signal over the line
signal
CA D
B
1
2
3
4
5
6
6INTEGRAL-WPM1 Manual
INTEGRAL
Connections
The image on the right shows INTEGRAL-
WPM1 panel connected to a paging
MC01 microphone using the input XLR
connector. A stereo line signal has been
injected using the two RCA connectors
with a minijack cable connected to the
mobile phone (or computer).
Other possibility would be using the
minijack input connector for the line input.
Use the level knobs at the front panel for
each input channel to define your mix of
the two signals (line and mic).
7INTEGRAL-WPM1 Manual
INTEGRAL
Connections
Remember that Phantom power for the
microphone can be activated at the rear
panel of the WPM1 before installation by
connecting the dedicated PHT jumper
(see image on page 5). As well, the talk-over
functionality (priority) of the microphone
signal over the line input can be activated
by removing the TKO jumper located at
the rear panel as shown in the figure be-
low.
The INTEGRAL-WPM1 needs to be con-
nected to an external 12-24Vdc power sup-
ply. DAS Audio´s INTEGRAL-PS12 with uni-
versal mains is ideal to be installed inside
walls and construction structures.
V+
V-
OUT +
V +
V -
Earth
N
L
OUT -
EARTH
INTEGRAL-PS12
INTEGRAL-Axxx or MAxxx models
Analog Audio from WPM1
LNK TKO
PHT
11
2
3
4
5
6
8INTEGRAL-WPM1 Manual
INTEGRAL
Installation
With each unit an electrical 86 x 86 mm box is included.
Contact a professional installer or authorized dealer for
the mounting process.
• Cut a squared hole in the wall to place the electrical
box.
• Place the electrical box and fix it to the wall. Previously
all cabling (speaker outputs, AC power and signal
input) has been installed in the wall with sufficient
length to provide proper stress relief.
• Run the cables out of the wall through the electrical
box.
• Attach the metal mounting ring to the electrical box
with the provided screws.
• Mount the connectors on the extremes of the installed
cabling.
• Connect the unit (speaker outputs, AC power etc.) and
secure it to the mounting ring.
9INTEGRAL-WPM1 Manual
INTEGRAL
Specifications
Line: -10dBV / 10Kohm
MIC: -40 or -20dBV / >1kohm
0dBV / 600ohm (max. + 17dBV)
Line: 20Hz – 20kHz
MIC: 120Hz – 20kHz
Line: <0.005%
MIC: <0.01%
Line: >105dB
MIC: >90dB
-30dB/ 2s
12Vdc
12-24Vdc, recommended INTEGRAL-PS12
25mA
86 x 86 x 34mm (3.38 x 3.38 x 1.34 in)
250g
Input Sensitivity / Impedance
Output Level / Minimum Load
Frequency Response
THD
Signal Noise Ratio
Talk-Over
Phantom Voltage
External Power Supply
Power Consumption
Dimensions (H x W x D)
Weight
10INTEGRAL-WPM1 Manual
INTEGRAL
Line drawings
H
WD
Inhaltsverzeichnis
Andere DAS AUDIO Stereoanlage Handbücher
