Data I/O FLX500 Bedienungsanleitung
096-0257-002D
Flash Programming Handler
500
Maintaining
the
After initial set up—
Please run and record the Performance Verifica-
tion Kit to establish a reference speed.
Contents
Contact Us
FLX500
Data I/O endeavors to ensure that the information in
this document is accurate.
Data I/O assumes no liability for errors, or for any
incidental, consequential, indirect, or special damages,
including, without limitation, loss of use, loss or
alteration of data, delays, or lost profits or savings,
arising from the use of this document or the product
which it accompanies.
No part of this document may be reproduced or
transmitted in any form or by any means, electronic or
mechanical, for any purpose, without written
permission from Data I/O.
Data I/O is a registered trademark of Data I/O
Corporation. FLX500 is a trademark of Data I/O
Corporation.
Data I/O Corporation acknowledges the trademarks of
other organizations for their respective products or
services mentioned in this document.
© 2007-2009 Data I/O Corporation
All rights reserved
—i—
Contents
1 … Tools and Materials • 1
Installing a Keyboard and Mouse • 1
Log File • 3
Adding Antivirus Software • 4
Run PV-Kit • 5
Spares Kits • 6
Hazardous Substance
Restrictions • 6
2 … Periodic Maintenance • 9
Gantry Movement and
Alignment • 10
Daily Maintenance • 10
Weekly Maintenance • 11
Monthly or Quarterly
Maintenance • 15
Annual Maintenance • 20
3 … Troubleshooting • 25
Rerunning the PV-Kit • 26
Actuating a Programmer Without
Power • 27
Fiducial Scan Errors • 28
Insufficient Vacuum • 30
Failures Picking and Placing • 30
PIN•31
Electrical Fuse • 31
4 … Correspondence • 33
Information We Need • 34
Customer Support • 35
5 … Sign-off Charts • 37
Daily Sign-off • 38
Weekly Sign-off • 43
Monthly/Quarterly Sign-off • 45
Annual Sign-off • 46
PV-Kit Performance • 47
Index • 49
Data I/O
FLX500
—ii—
—1—
Installing a Keyboard and
Mouse
The FLX500 incorporates a touch screen; however,
some maintenance procedures require the use of
a keyboard and mouse. The keyboard and
mouse plug into the back of the FLX500. See Fig-
ure 1 on the next page.
1 … Tools and
Materials
Data I/O
FLX500 Chptr 1
—2—
On early models using PS/2 ports, the system
power must be recycled after connecting a key-
board and mouse.
Connecting a keyboard and mouse depends on
your model. See the configuration in Figure 1
that matches your model.
Connecting a PS/2 Keyboard and
Mouse:
1. End a job if one is running.
2. Exit the FLX500 application–
3. Plug in the keyboard and mouse according
to the label. See Figure 1.
4. Switch off the power by pressing the power
switch (right side) once and releasing. Then
push it and release once more to turn the
power back on again.
Figure 1—Keyboard and Mouse Connections on the
back of the
FLX500
. Early models require PS/2 con-
nections (A). Later models require USB
connections (B).
PS/2
USB
A.
B.
1 … Tools and Materials Log File
—3—
Figure 2—Power Switch on the right side of the
FLX500
is a spring-loaded rocker switch.
Connecting a USB Keyboard and
Mouse:
Plug in the keyboard and mouse using either
USB port first. See Figure 1. (Power does not
need to be cycled.)
Log File
The FLX500 provides a log file that helps when
diagnosing problems. The file name has the date
and time the log was created and ends with .txt.
For example: FLX_20070607_162818.txt.
Log files are typically saved to the C: drive of the
FLX500 —C:\Flx_500\Log.
You can also save a log file to a different location:
1. Tap the Version button –
2. Tap Save Log –
3. Select a drive and path where you want the
FLXLog.zip file written, or insert a USB
memory stick and select (tap) the USB drive
listed.
4. Tap OK [], then OK, and close the dialog.
Data I/O
FLX500 Chptr 1
—4—
Two good ways to view the log files are:
• In the diagnostics—Tap Tools > Enter PIN
(Personal Identification Number) > Tap OK >
and View Log at bottom.
• Connecting a keyboard and mouse— see
previous headings. Then navigate to the Log
folder listed above.
Adding Antivirus Software
The FLX contains a CPU that runs Windows®XP
operating system.
Tools Required:
• Keyboard and Mouse
CAUTION: Possible virus hazard. The FLX
has no antivirus software installed from the
factory.
It is highly recommend that customers install
their own antivirus software. The software
should be set to run virus scans manually rather
than at a scheduled time unless you are sure that
the FLX will not be running jobs at that time. A
mouse and keyboard may be required for instal-
lation; see Installing a Keyboard and Mouse on
page 1.
NOTE: An antivirus program may affect
performance.
1 … Tools and Materials Run PV-Kit
—5—
Run PV-Kit
Running the Performance Verification Kit estab-
lishes a reference speed (PPH) to compare to if
you experience trouble in the future.
All hardware required to run the PV-Kit job,
including 16 devices, came with the FLX500. Con-
tact Data I/O for information about ordering
replacement parts for the PV-Kit.
NOTE: Be sure the Socket Adapters are
clean before running the PV-Kit job.
1. Set up for the PV-Kit job (Trays, Socket
Adapters, Actuator Plates). For instructions
see the on-screen Help.
2. Tap the Job File button.
3. Select the PV-Kit job from the Job Window
and tap OK.
4. Tap Run.
5. When it finishes, tap the Statistics button on
the Run Window and read the Throughput
displayed on the statistics window.
Record the PPH in the PV-Kit Performance
chart on page 47.
Figure 3—The Statistics Window displays
Throughput
, often abbreviated as PPH.
Data I/O
FLX500 Chptr 1
—6—
Spares Kits
A Basic Spares Kit is available for the FLX500.
Hazardous Substance
Restrictions
Disposal of FLX500
Dispose in a separately managed collection for
electronic equipment (per Directive 2002/96/EC)
or return to Data I/O (no charge).
RoHS for China
Restriction of the use of certain hazardous sub-
stances in electrical and electronic equipment in
China:
Data I/O Part Number
Basic Spares Kit 952-0377
Inhaltsverzeichnis
Andere Data I/O Hauptplatine Handbücher
Data I/O
Data I/O DUAL Bedienungsanleitung
Data I/O
Data I/O FlashPAK Bedienungsanleitung
Data I/O
Data I/O Sprint PLUS 48 Bedienungsanleitung
Data I/O
Data I/O OPTIMA Bedienungsanleitung
Data I/O
Data I/O UniSite-xpi Bedienungsanleitung
Data I/O
Data I/O PSV7000 Bedienungsanleitung
Data I/O
Data I/O 298 Bedienungsanleitung
Data I/O
Data I/O 29B Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
