Data Video RMC-140 Bedienungsanleitung
2005/9/5
Ì¿´´§ñЮ»ª·»© Þ±¨ º±®
ÍÛóèðð
ÎÓÝóïìð
Û®®±®ÿ
ËÍÛÎ ÓßÒËßÔ
ج¬°æññ©©©ò¼¿¬¿ª·¼»±ó¬»µò½±³
1
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not
use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The
unit may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are
provided for ventilation. To ensure safe and reliable operation
of this unit, and to protect it from overheating, do not block or
cover these openings. Do not place this unit on a bed, sofa,
rug, or similar surface, as the ventilation openings on the
bottom of the cabinet will be blocked. This unit should never be
placed near or over a heat register or radiator. This unit should
not be placed in a built-in installation unless proper ventilation
is provided.
7. This product should only be operated from the type of power
source indicated on the marking label of the AC adapter. If you
are not sure of the type of power available, consult your
Datavideo dealer or your local power company.
8. Do not allow anything to rest on the power cord. Do not locate
this unit where the power cord will be walked on, rolled over, or
otherwise stressed.
9. If an extension cord must be used with this unit, make sure that
the total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cords rating.
10. Make sure that the total amperes of all the units that are
plugged into a single wall outlet do not exceed 15 amperes.
2
11. Never push objects of any kind into this unit through the
cabinet ventilation slots, as they may touch dangerous voltage
points or short out parts that could result in risk of fire or
electric shock. Never spill liquid of any kind onto or into this
unit.
12. Except as specifically explained elsewhere in this manual, do
not attempt to service this product yourself. Opening or
removing covers that are marked Do Not Remove may
expose you to dangerous voltage points or other risks, and will
void your warranty. Refer all service issues to qualified service
personnel.
13. Unplug this product from the wall outlet and refer to qualified
service personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under
normal operating conditions. Adjust only those controls
that are covered by the operating instructions in this
manual; improper adjustment of other controls may
result in damage to the unit and may often require
extensive work by a qualified technician to restore the
unit to normal operation;
e. When the product has been dropped or the cabinet
has been damaged;
f. When the product exhibits a distinct change in
performance, indicating a need for service.
3
Table of Contents
WHATS IN THE BOX? .................................................................4
INTRODUCTION ...........................................................................5
FEATURE ......................................................................................6
INTERFACE ..................................................................................7
INSTALLATION .............................................................................8
Connect with SE-800 monitor outòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòç
Connect thru TLM-404 òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòç
Connect RS-232 from SE-800 òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòç
DISPLAY MODES .......................................................................10
SET UP MENU ............................................................................11
Color processor setting òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòïï
Video output settingòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòïí
SAMPLE CONNECTION DIAGRAMS........................................14
RMC-140 and SE-800 applicationòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòïì
SPECIFICATION .........................................................................15
PRODUCT REGISTRATION .......................................................16
SERVICE & SUPPORT ...............................................................17
4
Whats in the box?
1. RMC-140
2. User Manual
3. RS232 cable x 1
4. BNC 1.2m cable * 5
5. AC/DC Power Adapter
5
Introduction
Thank you for purchasing the RMC-140. This is an accessory
for the SE-800, and it can also be used for security camera
monitoring. In order to bring out the maximum performance of
this software, we recommend that you spend some time
reading this manual carefully.
Product Overview
The RMC-140 is especially designed for control by the SE 800,
via RS-232 port. In general, you can only select the main
output from one of four different video sources in the SE-800
by looking at the TLM-404 (4 x 4 LCD monitor) or other
similar products. You might not know which camera source
you want to switch to. With the RMC-140, everything becomes
easier and faster. You will be able to see next source preview
and next transition effect indicator showing on the same
monitor.
The RMC-140 also has an extra feature, you can select 4
different display modes, Quad, POP, PIP, or Next source
screen, plus tally light indicators on the same monitor.
6
Features
Next source preview
Combine 4 different video sources into one video output
(4 display modes, Quad, POP, PIP, and full screen.)
Next transition effect indicator
Tally light indicator
7
Interface
1. 4 composite input
2. Monitor output (Quad, POP, PIP & Next selectable)
3. Full screen next source preview output, Effect and
Tally light indicators
4. Power connector (DV12V)
5. Tally light signal out (15pin & 3.5mm jack)
6. RS-232 input from SE-800
7. RS-232 by pass
8. Menu
9. Display mode selects (Quad, POP, PIP and Next)
1 2
3
4
5
6
7
8
9
8
Installation
1. Connect four monitor outputs from SE-800,
Or loop thru from TLM-404.
9
Plug in the power adapter, and connect to the power.
Now RMC-140 is ready to use.
10
Display Modes
The four display modes of the RMC 140 are:
Next Source PIP
Shows a full screen display of
the cued up source.
Shows a full screen of the Live
Source with a PIP of the cued
up source.
Quad POP
Shows all four sources with
Tally Indication.
Shows the Live Source in the
main window, plus the other
three sources with Tally
Indication.
In all display modes the active effect in the SE 800 is shown across
the bottom of the screen.
11
SET UP Menu
The RMC 140 has a simple Set
Up Menu, which is navigated
with the +, -, Up, Down and
Menu buttons.
To call up the menu press the
menu button.
Within the menu there are Color Processor Settings for each input,
and a Video Output Setting.
Color Processor Settings. These settings do not affect the
actual video channels on the mixer; they are only fine tune
adjustments within the RMC 140.
Use the Up or Down buttons to
navigate the menu, and
highlight the channel you
require. (In this example
Channel A)
12
Then press the menu button, to
enter the settings menu
Use the Up or Down buttons to
navigate the menu, and
highlight the channel you
require. (In this example
Channel A)
Then press the menu button, to
enter the settings menu
Use the Up and Down buttons
to navigate the options, and
the + and buttons to adjust
the values (-99 - +99).
Once the values are set
highlight Save and Exit, and
press the menu button.
13
Video Output Settings
The Video Output can be set to Same or Separate. Same will feed
identical signals to both outputs, whereas Separate will feed
whichever display mode you have selected to the Main Output (PIP,
QUAD, POP, Next Source), and a full screen next source preview
to the Next Source Output.
Main Output This will always show the chosen
display pattern i.e. PIP, POP, QUAD or Next
Source.
Next Source Output This can either give the
same display pattern as the Main Output or a full
screen next source preview.
To change from Same to
Separate or vice versa,
highlight Video Output and
press the menu button to
toggle from one to the other.
Once set highlight Save and
Exit, and press the menu
button.
14
Sample connection diagrams
Example 1: RMC-140 and SE-800 Application
15
Specification
Video Formats
Analog Composite NTSC or PAL (NTSC and PAL are
separate models)
Video Inputs
4 Composite
Video Output
1 Composite (Quad, POP, PIP, Next source preview)
1 Composite (Full screen next source preview)
RS-232 Data Control Port
From SE-800- Connecting Datavideo SE-800 RS-232
By pass- For other RS-232 remote control devices
Tally Light Signal Out
1 15pin
4 3.5mm mini jack
Video Bandwidth
Composite 4.6 MHz
DG, DP +/- 5%, 5 degrees
Signal/Noise Ratio:
Video > 50dB
Dimensions W x D x H
6.3" x 3.93" x 1.95"
160mm x 100mm x 49.5mm
Weight
5.36 lb, 2.5 kg
Power
Input: 12V
16
Product registration
Go on line www.datavideo.info/product_reg.htm for product
registration
See the warranty card for warranty period
17
Service and Support
It is our goal to make your products ownership a satisfying experience. Our
supporting staff is available to assist you in setting up and operating your
system. Please refer to our web site www.datavideo-tek.com for answers to
common questions, support requests or contact your local office below.
Datavideo Corporation (USA)
12300-U East Washington Blvd., Whittier, CA 90606 USA
Datavideo Technologies Europe BV
Californiedreef 263565 BL Utrecht, The Netherlands
Tel: +31 30 261 9656 info@datavideo.nl www.datavideo.info
Datavideo UK Limited
Unit 2 Waterside Business Park, Hadfield, Glossop, Derbyshire SK131BE UK
Tel: +44 1457 851000 sales@datavideo.co.uk www.datavideo.info
Datavideo Technologies Co., Ltd.
10F, 176 Jian-Yi Rd, Chung Ho City, Taipei Hsien, Taiwan 235
Tel: +886 2 8227 2888 info@datavideo.com.tw
www.datavideo.com.tw
Datavideo Technologies China Co.
2F-D, 2 Lane 777, West Guangzhong Rd, Zhabei District, Shanghai, China
Tel: +86 21 5603 6599 service@datavideo.cn www.datavideo.cn
Datavideo Technologies (S) PTE Ltd.
No. 100, Lorong 23 Geylang, #01-03 DCentennial Bldg, Singapore 388398
Tel: +65 6749 6866 info@datavideo.sg www.datavideo.sg
P/N: 082060374E2
All the trademarks are the properties of their respective owners.
Datavideo Technologies Co., Ltd. All rights reserved 2005.
Andere Handbücher für RMC-140
1
Andere Data Video Aufnahmegeräte Handbücher
Data Video
Data Video AD-10 Bedienungsanleitung
Data Video
Data Video MS-3000 Bedienungsanleitung
Data Video
Data Video HDR-70 Bedienungsanleitung
Data Video
Data Video AD-100 Bedienungsanleitung
Data Video
Data Video TVS-1200A Bedienungsanleitung
Data Video
Data Video MS-900 Bedienungsanleitung
Data Video
Data Video TBC-7000 Bedienungsanleitung
Data Video
Data Video HS-1300 Bedienungsanleitung
Data Video
Data Video GO KMU-100 STUDIO Bedienungsanleitung
Data Video
Data Video TC-100 Bedienungsanleitung
Data Video
Data Video MS-2850 Bedienungsanleitung
Data Video
Data Video HS-2200 Bedienungsanleitung
Data Video
Data Video HS-550 Bedienungsanleitung
Data Video
Data Video HDR-45 Bedienungsanleitung
Data Video
Data Video TVS-2000A Bedienungsanleitung
Data Video
Data Video MS-2850G Bedienungsanleitung
Data Video
Data Video TVS-1000 Bedienungsanleitung
Data Video
Data Video HS-2800 Bedienungsanleitung
Data Video
Data Video DVK-100 CHROMA KEY Bedienungsanleitung
Data Video
Data Video TBC-6000 Bedienungsanleitung
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
