Datakom DK-40 Bedienungsanleitung

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 1 -

[email protected]

http://www.datakom.com.tr

Tel: +90 216 466 84 60

Fax: +90 216 364 65 65

DK-40 COMPRESSOR CONTROLLER

INTRODUCTION

DK-40 is a state of the art unit for the control

of both screw and piston type compressors.

The unit integrates all functions needed in a

compressor system. Thus no extra units are

required in a compressor panel providing

cost reduction and simplicity.

The unit is directly powered from 230/400 volt

mains. It provides power supply for fault

switches and sensors. Thus external

transformer is not required in the panel.

The unit monitors mains phase voltages and

frequency. It features high/low voltage and

phase order protections.

The standard logic level serial port features

MODBUS communication. The unit allows

monitoring and programming through

computer.

FEATURES

Pressure driven automatic start and stop

Voltage Protection Relay function

Phase Order Protection Relay function

Mains phase voltages display

No need for external transformer

Star / Delta startup

Load solenoid control

1 programmable relay output

Optically isolated configurable digital inputs

2 pressure sensor inputs

2 temperature sensor inputs

Additional motor PTC input

Logic level serial port

MODBUS-RTU communication

Password protected front panel programming

Low panel depth, easy installation

Wide operating temperature range

Sealed front panel (IP54)

2 part connector system for easy installation

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 2 -

SAFETY NOTICE

Failure to follow below instructions will

result in death or serious injury

•

Electrical equipment should be installed only by qualified

specialist. No responsibility is assured by the

manufacturer or any of its subsidiaries for any

consequences resulting from the non-compliance to

these instructions.

•

Check the unit for cracks and damages due to

transportation. Do not install damaged equipment.

•Do not open the unit. There is no serviceable parts inside.

•

Fuses must be connected to the power supply and phase

voltage inputs, in close proximity of the unit.

•

Fuses must be of fast type (FF) with a maximum rating of

6A.

•

Disconnect all power before working on equipment.

•

When the unit is connected to the network do not touch

terminals.

•

Any electrical parameter applied to the device must be in

the range specified in the user manual.

•

Do not try to clean the device with solvent or the like.

Only clean with a dry cloth.

•

Verify correct terminal connections before applying

power.

•

Only for front panel mounting.

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 3 -

TABLE OF CONTENTS

Section

1. INSTALLATION

1.1. FRONT / REAR PANELS

1.2. MECHANICAL INSTALLATION

1.3. ELECTRICAL INSTALLATION

1.4. CONNECTION DIAGRAM

2. PUSHBUTTON FUNCTIONS

3. DISPLAY NAVIGATION

4. MODES OF OPERATION

5. ALARMS AND WARNINGS

6. OTHER FEATURES

6.1. RESETTING SERVICE COUNTERS

6.2. MODIFYING HOUR COUNTERS

6.3. SELECTION OF HOUR COUNTING METHOD

6.4. CONNECTION TOPOLOGIES

6.5. PREVENTING PRESSURE LOSS

6.6. ALARM HISTORY

7. INPUTS

8. RELAY OUTPUTS

9. PROGRAMMING

9.1. INTRODUCTION TO PROGRAMMING

9.2. PARAMETER LIST

10. MODBUS COMMUNICATIONS

10.1. DESCRIPTION

10.2. MODBUS REGISTER LIST

11. MULTIPLE CONTROLLER OPERATION

12. DECLARATION OF CONFORMITY

13. TECHNICAL SPECIFICATIONS

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 4 -

1. INSTALLATION

Before installation:

•Read the user manual carefully, determine the correct connection diagram.

•Remove all connectors and mounting brackets from the unit, then pass the unit through

the mounting opening.

•Put mounting brackets and tighten. Do not tighten too much, this can brake the enclosure.

•Make electrical connections with plugs removed from sockets, then place plugs to their

sockets.

•Note that the power supply terminal is separated from measurement terminals.

Below conditions may damage the device:

•Incorrect connections.

•Incorrect power supply voltage.

•Voltage at measuring terminals beyond specified range.

•Connecting or removing data terminals when the unit is powered-up.

•Overload or short circuit at relay outputs

•Voltage applied to digital inputs over specified range.

•High voltage applied to communication port.

Below conditions may cause abnormal operation:

•Power supply voltage below minimum acceptable level.

•Power supply frequency out of specified limits

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 5 -

1.1 FRONT / REAR PANELS

1.2 MECHANICAL INSTALLATION

Panel Cutout Required Panel Depth

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 6 -

1.3 ELECTRICAL INSTALLATION

Do not install the unit close to high electromagnetic noise

emitting devices like contactors, high current busbars,

switchmode power supplies and the like.

Although the unit is protected against electromagnetic disturbance, excessive disturbance

can affect the operation, measurement precision and data communication quality.

•ALWAYS remove plug connectors when inserting wires with a screwdriver.

•Fuses must be connected to the power supply and phase voltage inputs, in close

proximity of the unit.

•Fuses must be of fast type (FF) with a maximum rating of 6A.

•Use cables of appropriate temperature range.

•Use adequate cable section, at least 0.75mm

(AWG18).

•Follow national rules for electrical installation.

•Use only the appropriate cable and connector for serial port connection.

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 7 -

1.4 CONNECTION DIAGRAM

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 8 -

2. PUSHBUTTON FUNCTIONS

Programming and measurement displays are visualized using below buttons:

BUTTON DESCRIPTION

FUNCTION

Displays next parameter.

Resets faults.

Saves adjusted value.

RUN

Run the compressor and reset existing

alarms.

Increase value.

STOP

Stop the compressor and reset existing

alarms.

Decrease value.

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 9 -

3. DISPLAY NAVIGATION

Usually the upper display shows the pressure-1 value or the pressure switch-1 position.

The lower display shows the temperature-1.

Other values are scrolled by pressing the MENU

button. For better clarity, the upper

display will show the parameter name and the lower display will show the parameter value.

Some parameters are longer than 1 display. For these parameters, when MENU

button

is presssed the parameter name apeears on the upper display. When MENU button is

released, the parameter value is shown on both displays.

Display of some parameters are selectable with program parameters and

may differ following compressor manufacturers.

In the occurrence of a fault condition, the fault code will appear on the

upper display.

Below is a list of messages shown on the upper display in normal operation,

programming and alarm display modes:

MESSA

GE DESCRIPTION MODE

bar

barbar

bar

set

setset

set

Start pressure and stop pressure set

values Display

FrQ

FrQFrQ

FrQ

Mains frequency Display

L12

L12L12

L12

L1-L2 phase-to-phase voltage Display

L23

L23L23

L23

L2-L3 phase-to-phase voltage Display

L31

L31L31

L31

L3-L1 phase-to-phase voltage Display

SHSH

SHA

Hours remaining to service A Display / Program / Alarm

SHB

SHBSHB

SHB

Hours remaining to service B Display / Program / Alarm

SHC

SHCSHC

SHC

Hours remaining to service C Display / Program / Alarm

SHD

SHDSHD

SHD

Hours remaining to service D Display / Program / Alarm

DK-40 USER MANUAL V2.6 (02.08.2011)

K13D01-E - 10 -

MESSA

GE DESCRIPTION MODE

SHE

SHESHE

SHE

Hours remaining to service E Display / Program / Alarm

C-H

C-HC-H

C-H

Total compressor hours

(ON_LOAD+OFF_LOAD+STOP) Display

R-H

R-HR-H

R-H

Total Run Hours

(ON_LOAD+OFF_LOAD) Display

L-H

L-HL-H

L-H

Total load time (load contactor active) Display

o/o

o/oo/o

o/o

Load hours / Run hours percentage Display

E-t

E-tE-t

E-t

Motor PTC value or switch position Display

t-t-

t-2

Temperature-2 value or switch position Display

d-p

d-pd-p

d-p

Differential Pressure Display

n--

n--n--

n--

Remaining starts for the last hour Display

rEL

rELrEL

rEL

Software version Display

Ah1

Ah1Ah1

Ah1

Alarm history 1 Display

n-C

n-Cn-C

n-C

Switch closed Display

N-O

N-ON-O

N-O

Switch open Display

SEP

SEPSEP

SEP

Waiting for separator filter pressure drop Display

S P

S PS P

S P

Remote Stop mode Display

RUN

RUNRUN

RUN

Remote Start mode Display

aL1

aL1aL1

aL1

Alarm code 01 Display

a99

a99a99

a99

Alarm code 99 Display

p99

p99p99

p99

Program parameter 99 Program

usr

usrusr

usr

Enter password Program

seL

seLseL

seL

Select parameter Program

Inhaltsverzeichnis

Andere Datakom Controller Handbücher

Datakom

Datakom DKG-190 Bedienungsanleitung

Datakom

Datakom DKG-509 Bedienungsanleitung

Datakom

Datakom D-500 MK3 Bedienungsanleitung

Datakom

Datakom D-100 MK2 Bedienungsanleitung

Datakom

Datakom DKM-046 Bedienungsanleitung

Datakom

Datakom DK-45 MK2 Bedienungsanleitung

Datakom

Datakom DKG-109 Bedienungsanleitung

Datakom

Datakom DKG-225 Bedienungsanleitung

Datakom

Datakom DFC-0108 Bedienungsanleitung

Datakom

Datakom D-500 Bedienungsanleitung

Datakom

Datakom DK-70 Bedienungsanleitung

Datakom

Datakom D-500 MK3 Bedienungsanleitung

Datakom

Datakom DKG-319 Bedienungsanleitung

Datakom

Datakom D-300 MK2 Bedienungsanleitung

Datakom

Datakom DKG-325 Bedienungsanleitung

Datakom

Datakom D-200 MK2 Bedienungsanleitung

Datakom

Datakom D-500 MK2 Bedienungsanleitung

Datakom

Datakom DKG-307 Bedienungsanleitung

Datakom

Datakom DKG-108 Bedienungsanleitung

Datakom

Datakom DKG-255 Bedienungsanleitung

Datakom

Datakom DKG-205 Bedienungsanleitung

Datakom

Datakom DKG-114 Handbuch

Datakom

Datakom DKG-329 Bedienungsanleitung

Datakom

Datakom DKG-119 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung