Via monte Nero, 40/B – 21049 TRADATE (VA) ITALY
P
one: +39 (0)331841070 Fax:+39 (0)331841950 - e-m
ail:
[email protected] -
www.datexel.itConfiguration interface for
serial ports RS-232
GENERAL DESCRIPTION
T e configuration interface PRODAT-04 allows to program, by dedicated software, all t e DATEXEL devices of t e SMART and SLIM series using bot fixed
workstations and laptops wit communication serial ports RS-232 on board.
An internal battery is available for t e eventual supply of t e transmitter on programming; t e battery's output voltage is provided on t e connector J4; t e same
voltage is used to power t e interface w en t e output voltage of t e serial port is lower of t e minimum voltage value necessary to t e rig t working of t e
device (± 7Vdc).
T e 1500 Vac galvanic isolation between t e lines of input/power supply and output is obtained by means of opto-couplers on t e data lines and a DC/DC
converter on t e power supply.
By t e dedicated cable (CVPR-03) it is possible to configure t e Intrinsically Safe devices.
Wit t e PRODAT-04 are provided t e standard cable CVP or t e cable CVPR-03, t e CD-ROM containing t e drivers to install t e programming software and
two Jack connectors for t e terminals J3 and J4.
T e configuration interface PRODAT-04 is in compliance wit t e Directive 2004/108/EC on t e Electromagnetic Compatibility.
EATURES
- Adapt to configure the devices of SMART and SLIM series
- Galvanic isolation between the transmission and receiving sides
- Internal battery
- Connector for external supply input
- Connector for external supply output
- EMC compliant – CE mark
- Programming of the DATEXEL devices, on field too
USER INSTRUCTIONS
A) Use with Standard devices.
The device on programming must be always powered as shown on its technical data-sheet.
T e interface PRODAT-04 must be connected to t e serial port RS-232 by pin-to-pin cable to t e connector J1 ; connect t e ' CVP ' cable from t e connector J2
to t e PRGM connector of t e device on programming.
It is also possible to power t e device on programming using t e internal battery (only for transmitters) connecting t e connector J4 to power supply terminal of
t e transmitter.
B) Use with Intrinsically Safe devices.
The device on programming must be always connected in according to the Safety Specifications reported on the technical data-sheet of the device .
The configurable devices are the following:
- DAT 1010 IS , DAT 1010 IS/HT;
- DAT 1015 IS , DAT 1015 IS/HT;
- DAT 1065 IS , DAT 1065 IS/HT;
- DAT 2015 IS , DAT 2015 IS/HT;
- DAT 4035 IS , DAT 4035 IS/HT.
T e connection diagrams A and B are s own on next page in t e section “PRODAT-04: Connections”.
To use t e PRODAT-04 refer to t e section “Installation Instructions”.
PRODAT-04
Type of battery ( Optional ) 6LF22 / 9 Vdc
External supply ( Optional ) 10 ÷ 30 Vdc (Transmitters)
18 ÷ 30 Vdc (Converters)
Current consumption < / =10 mA
RS-232 connection (pin-to-pin cable) DB9 connector
CVP/CVPR-03 connection 4 ways RJ11 plug
External supply IN connection 2.1 mm JACK connector
External supply OUT connection 2.5 mm JACK connector
Galvanic isolation among t e ways 1500 Vac, 50 Hz, 1 minute
Electromagnetic Compatibility Emission: EN 61000-6-3
Immunity: EN 61000-6-1
Operative temperature 0 ÷ 40 °C
Storage temperature (wit out battery) -20 ÷ 60 °C
Relative Humidity (not condensing) 0 ÷ 90 %
Weig t about 250 g.
Optional accessories - CVPR03 for t e programming of SMART
series DAT xxxx IS modules suitable for
application in azardous areas
TECHNICAL SPECI ICATIONS (Typical at 25 °C and in nominal conditions)
