Davey Steriflo UV130 Bedienungsanleitung

Please pass these instructions on to the operator of this equipment.

Installation and Operating

Instructions

Ultra Violet

Water Treatment System

UV130 and UV250

WARNING: The UV Chamber operates under pressure.

Under no circumstances should the UV Chamber be

disassembled unless the internal pressure of the unit

has been relieved. Failure to observe this warning will

expose persons to the possibility of personal injury

and may result in damage to the UV system or other

property.

This unit is designed to treat water at ambient

temperatures (5˚C to 45˚C). Contact your dealer for

details of UV systems suitable for hot water service.

DO NOT DISASSEMBLE ANY COMPONENTS UNTIL YOU

HAVE FULLY READ THESE INSTRUCTIONS!

Maximum operating pressure for stainless steel UV

chambers is 850kPa (125 psi). If this pressure can be

exceeded or if operating close to this pressure if a

suitable pressure limiting valve in the supply to the UV

chamber.

Plastic UV chambers have a maximum operating

pressure of 400kPa (60 psi).

DO NOT LOOK AT UV LAMP WHILE LAMP IS

OPERATING Ultra violet radiation is harmful to

skin & eyes.

Ultra Violet

Water Treatment System

Contents

Preparing your system.................................................................................... 5

Choosing a Site .............................................................................................. 5

Housing your Sterio System ......................................................................... 5

Power Connection .......................................................................................... 6

Electrical Power Surge Protection .................................................................. 8

Pipe Connections ........................................................................................... 8

Pre-treatment (drinking water)........................................................................ 9

Lamp Installation ............................................................................................ 9

Operation...................................................................................................... 10

Maintenance ................................................................................................. 10

Water Quality ................................................................................................ 12

Lamp Alarm System ..................................................................................... 12

Trouble Shooting .......................................................................................... 13

Part Numbers ............................................................................................... 14

After Sales Service ....................................................................................... 14

WARNINGS .................................................................................................. 15

Davey Repair or Replacement Guarantee ................................................... 16

Congratulations on your purchase of a high quality, Australian made Sterio

Ultra Violet water treatment system. All components have been designed and

manufactured to give trouble free, reliable operation.

Your new Sterio system incorporates a lamp failure system design feature that

enables you to be warned of a lamp failure by :-

1. A lamp failure LED

2. An audible alarm

3. Remote alarm contacts

In addition when the alarm “beeps” on and off, the lamp is due to be changed so

that effective treatment is maintained.

Before installing your new Sterio, please read all instructions

carefully as failures caused by incorrect installation or

operation are not covered by the guarantee. Your Ultra Violet

water treatment system is designed to handle clean water.

The system should not be used for any other purpose without

specic referral to CCL. The use of the system with ammable,

corrosive and other materials of a hazardous nature is

specically excluded.

NOTE: The quartz sleeve

has been factory tted,

and there is no need to

remove these endcaps

on rst installation. Before

removing endcaps, please

read the Maintenance

section of these instructions

completely.

The appliance is not intended

for use by young children

or inrm persons without

supervision. Young children

should be supervised to

ensure they do not play with

the appliance.

Alarm

LED

(Red)

Alarm reset

On LED

(Amber)

Power Lead

1.5 metre

OUTLET

or INLET

OUTLET

or INLET

Lamp Lead

1 metre

Treatment

Chamber

Drain

Plug

Quartz Sleeve

(pre-installed

in chamber)

Lamp

Preparing your system

On removing your Sterio system from its carton you should check all

components, especially the lamp, to ensure all are present and have not been

damaged in transportation. You should have:

1. Power supply control box with indicator light(s) and electrical ex

2. UV lamp (or lamps)

3. Treatment chamber with mounting brackets

Choosing a Site

Choose a site with a rm mounting position. Allow room for removal of the

lamp and sleeve during servicing. Leave a chamber lengths space at the lamp

connector end for lamp removal, with 100mm free at the other end for access to

the end nut. The ‘open’ end nut and the blank end nut are interchangeable, so

lamp removal can be from either end.

Housing your Sterio System

To protect your Sterio system from the weather, make sure the site is water

proof, frost free and has adequate ventilation. The unit should be either

horizontally mounted with the inlet/outlet facing upwards or vertically mounted

with the inlet/outlet at the bottom. Allow for drainage, to avoid damage to ooring

etc., that over time may occur from leaking pipe joints or seals and allow room to

remove the lamp.

WARNING: Some insects, such as small ants, nd

electrical devices attractive for various reasons. If your

site or enclosure is susceptible to insect infestation you

should implement a suitable pest control plan.

Power Connection

WARNING: When servicing or attending your Sterio,

always ensure power is switched off and lead

unplugged. Electrical connections should be serviced

only by qualied persons. If the electrical supply lead of

this system is damaged, it must only be replaced by a

qualied service personnel.

Connect lead to power supply designated on control box label. Earth stainless

steel chambers using bolt provided on the chamber (see illustration below).

Install the power supply enclosure above the treatment

chamber so that in the event of a leak, water cannot

drip down the lamp lead into the enclosure.

CAUTION: The supply cord is necessary for lamp

changing. The three pin supply plug must remain

accessible after installation. If installed to xed wiring

without the plug a two pole switch must be tted and

its ON and OFF positions shall be marked.

The Sterio control box has a red LED alarm indicator

light mounted on its front panel, adjacent to the amber

“power on” LED. This light will be illuminated whenever

the Sterio control box senses no lamp current. There

is also an audible alarm in the event of lamp failure. The

LED and/or alarm will only work when unit is connected

to the correct electrical supply.

Electrical Power Surge Protection

An electrical power surge or spike can travel on the supply lines and cause

serious damage to your electrical equipment. The Sterio control box has a 2 Amp

fuse

to protect the circuit. The fuse is not a lightning arrestor and may not protect the

Sterio if lightning or a very powerful surge hits the unit.

If the installation is subject to electrical power surges or lightning we strongly

recommend the use of suitable additional surge protection devices on ALL

electrical equipment.

We recommend the use of an RCD or earth leakage circuit breaker on the power

supply to your unit.

DO NOT LOOK AT UV LAMP WHILE LAMP IS

OPERATING Ultra violet radiation is harmful to

skin & eyes.

DO NOT DISASSEMBLE ANY COMPONENTS UNTIL YOU

HAVE FULLY READ THESE INSTRUCTIONS!

Pipe Connections

NOTE: Prior to installation remove the transport plugs

from the inlet, outlet and lamp end cap.

Never use PVC pipe directly connected to unit. PVC pipe and ttings can be used

after 90o bends of a suitable material are connected to the inlet and outlet of the

chamber. Larger diameter pipe may be used to minimise resistance to ow, but

maximum ow rates should not be exceeded, as correct water treatment cannot

be assured at higher ows. If ows may exceed the design maximum, install a

ow restriction device.

Do not use pipe thread sealing compounds (especially

hemp) on any part of this unit. ONLY use Teon

sealing tape.

Use unions at pipe connections to enable easy removal and servicing. Use

sufcient tape to ensure airtight seal and do not over tighten. To prevent strain on

unit threads always support heavy inlet and outlet pipes.

Pre-treatment (drinking water)

Pre-ltration is usually required to ensure that particulate matter does not shield

micro-organisms from the UV light. Sand ltration or 20 micron cartridge ltration

is the usual minimum. In some cases, particularly with surface water, ner

ltration may be necessary, or if cysts like Giardia or Cryptosporidium may be

present.

In this case 1 micron ltration is required, not necessarily for the whole supply,

ltration for the drinking tap only may be practical.

Lamp Installation

Once the Sterio Treatment Chamber has been connected to the pipework, the

installation should be checked for water leaks.

Attach the “DO NOT LOOK AT LAMP” sticker in an obvious position on the

treatment chamber, check that the chamber is clean to ensure the sticker will

adhere correctly.

The Quartz Sleeve is pre-installed in the treatment chamber, and provided the

endcaps have not been disturbed or undone, is able to withstand well in excess of

the maximum operating pressures.

If the chamber test is successful, it is now time to insert the lamp. DO NOT

INSERT THREE PIN POWER PLUG TO POWER OUTLET YET!

Expose the connection end of the lamp from its transport tube and protective

wrapping. The lamp connection socket is “keyed” to ensure correct alignment.

Carefully remove the tube fully from its transport tube, touching the lamp as little

as possible. Handle the lamp by the ends where possible. Wipe with clean cloth

and methylated spirits if ngerprints or dirt need removing.

Slide the lamp into the chamber, t lamp connection socket and then fasten the

end washer into the endcap, with the screws provided.

Operation

Once all leak testing and lamp tment has been completed, open valves and

allow water to ll the chamber. Connect three pin plug to outlet and switch on. The

“Mains On” Amber LED will be illuminated and the red alarm light will ash slowly.

Allow two minutes for the UV lamp to reach full intensity before starting water ow.

Full lamp performance for a new installation will be achieved in 24 hours. On a

new installation where no other form of sterilisation has been in constant usage,

we recommend ushing the pipework with a suitable sanitiser such as Steritank

HP (only available in New Zealand) or Acquasafe at 100mg/L. This solution

should be left in the piping for at least an hour and preferably overnight.

The Steritank HP or Acquasafe solution can be dosed to the water tank or if

necessary added as a shot dose to the bowl of any lter housing installed with the

UV system and slowly ushed into the piping.

If dosed to the water tank the Steritank HP or Acquasafe will be left in the water

as it is tasteless and suitable for use in drinking water. If added as a shot dose it

should be rinsed out through a nearby tap.

Davey Water Products Limited cannot accept responsibility for loss or damage

resulting from incorrect or unauthorised installations.

Maintenance

Lamp changing (every year of operation):

1. Shut valve(s) so that water cannot ow through steriliser

2. Switch off steriliser by unplugging mains

3. Undo end cover screws

4. Unplug lamp connector

5. Remove lamp

Reverse procedure when replacing lamp, ensuring that lamp is centrally located

in the chamber. Handle only by the ends.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Davey Wasserfiltersystem Handbücher

Davey

Davey Crystal Clear 39075 Handbuch

Davey

Davey STERIFLO SF1000S mkII Bedienungsanleitung

Davey

Davey EMX3600 Montageanleitung

Davey

Davey EcoPure DEP2540 Bedienungsanleitung

Davey

Davey EcoSalt MC12ORP Handbuch

Davey

Davey CrystalClear DCC2550 Bedienungsanleitung

Davey

Davey ChloroMatic MCS16C Handbuch

Davey

Davey Microlene UV68-CA Bedienungsanleitung

Davey

Davey microlene Bedienungsanleitung

Davey

Davey EAFM7 Bedienungsanleitung

Davey

Davey EcoSalt 2 DES2-15E Bedienungsanleitung

Davey

Davey AquaReviva DAR20C Handbuch

Davey

Davey CrystalClear DCC2140 Bedienungsanleitung

Davey

Davey microlene MCS Bedienungsanleitung

Davey

Davey aquashield centurion ASC50 Bedienungsanleitung

Davey

Davey ProMatic 24 Handbuch

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung