DAVIS 7716A Bedienungsanleitung
1
Mounting Tripod Kit
Installation Manual
For use with Davis’s wireless and cabled Vantage Pro2 weather stations, the
Mounting Tripod simplifies installation. The tripod supports the Integrated
Sensor Suite (ISS) or other station, and features adjustable feet which enable
mounting on level surfaces or roof peaks.
Components
The Mounting Tripod includes the following poles and mounting hardware.
Please make sure you have everything you need before beginning.
Poles
Hardware
Tripod
Anemometer
Extension
Tube
Long
Extension
Tube
(swaged end)
Feet
Bracket
5/16" Flat Washers
5/16" Lock Washers
5/16"
Label
Pitch Pads
5/16" Heavy Duty
Hex Nuts
5/16" Bolt screws
U-Bolt
1/4" x 2" Lag Screws
5/16" Square Nuts
8" Cable Ties
Saddle
Vertical
Stop
Plate
Hex Nuts
Heavy Duty
Tripod Assembly
2
Tools for Setup
• Adjustable wrench
• Compass or local area map
• Drill with 3/16" or 13/64" (5 mm) bit for the 1/4" lag screws
Tripod Assembly
1. Unfold the tripod so the three feet on the tripod legs are flat on the ground.
2. Thread a hex nut almost all the way onto all six of the 5/16" bolts.
3. Insert one of the 5/16" bolts into the hole in vertical stop plate.
4. Insert the 5/16" bolt with vertical stop plate into one of the holes in the tripod's
lower bracket and thread a square nut onto the end of the bolt, on the inside of
the bracket.
Do not thread the square nut too far up the bolt.
5. Repeat this procedure for the remaining 5/16" bolts. Place them into the holes in
both the top and bottom tripod brackets, threading a square nut on the end of
each bolt.
Do not thread the square nuts too far up the bolts.
6. Insert the long extension tube into the tripod, sliding it through the brackets.
The vertical stop plate should keep the tube from sliding all the way through.
7. Secure the extension tube by tightening the square and hex nuts on the
5/16" bolts until the bolts hold the tube in place securely.
8. Apply pitch pads to the bottom of each
foot.
5/16" Bolt
Hex Nut
Square Nut
Assemble nuts and bolts
in Tripod brackets.
Do not tighten.
Use Vertical Stop Plate
on one of the lower
bracket bolts.
Slide Long Extension Tube
through center of Tripod brackets.
Tighten nuts and bolts.
Vertical
Stop Plate
Long
Extension
Tube
Foot
Pitch Pad
Mounting the Tripod
3
Mounting the Tripod
Mount the tripod with long extension tube on the desired surface, as shown below.
On the following pages are instructions for securing your sensor array or ISS onto
the long extension tube
ROOF MOUNTING DECK MOUNTING
ISS
Long Extension Tube
(use level or plumb line
to nd true vertical)
Deck or other
at surface
Tighten nut when
proper angle of feet
determined
Long Extension Tube
1/4 x2”
Lag Screw
(6 places)
Flat
Washer
1/4 x2”
Lag Screw
(6 places)
Flat
Washer
ISS
.
Note: Any metal object may attract a lightning strike, including your weather
station or tripod. If lightning strikes your station or strikes somewhere
nearby, the station's internal electronics may suffer anywhere between little
to extensive damage. The station itself has been designed with
considerable surge protection, but to safeguard nearby equipment and
structures, we recommend following local recommendations on properly
grounding your installation.
For more information, contact your local lightning protection authority and/or
refer to the latest edition of the following articles:
Mounting the Tripod
4
• MIL-HDBK-419A: Grounding, Bonding, and Shielding for Electronic
Equipment and Facilities.
• National Fire Protection Association: Standard for Installation of Lightning
Protection Systems, ANSI/NFPA 780, National Fire Protection Association,
Quincy, MA.
• NEC, National Electrical Code; National Fire Protection Information, Quincy,
MA
Attaching the Vantage Pro2 ISS to the Anemometer
Extension Tube
For Vantage Pro2, the anemometer extension tube provided as part of the
mounting tripod will be used to support the ISS, which does not come with its own
pole. You can mount your ISS on this tube with both sides together or separate. For
better access to the hardware securing the rain collector side, remove the rain
collector cone by rotating it counter-clockwise and lifting it off of the base.
Mount your ISS and anemometer on the anemometer extension tube together or
separately. See the illustration below for more information. Make sure the swaged
end of the tube is pointing downward as you secure the ISS to it.
14Hex ut
14oc asher
Metal acing Plate
U-olts
ain Collector
Mounting ase
14lat asher
14oc ashe
r
14Hex u
t
Anemometer
Mounting ase
Option 1: Installing ISS and Anemometer Together
Remember when mounting both sides together that whichever side of the ISS is
mounted first, the U-bolt from the opposite side ALSO must be placed around the
pole before you tighten anything. (If it is not, there is no way to slide it in later.)
When both sides of the ISS are mounted together with the anemometer arm
pointing north, the solar panel on the rain collector side is facing south. In the
Northern Hemisphere, this positions the solar panel for optimal exposure to the
sun. In the Southern Hemisphere, you will need to position the solar panel facing
north for optimal sun exposure.
Mounting the Tripod
5
The anemometer is factory calibrated to report the correct wind direction when the
anemometer arm is aiming north. If you cannot install the anemometer with the
arm aiming north, see your Vantage Pro2 Console Manual for instructions on how
to calibrate the console to display the correct wind direction.
1. Place the U-bolt for the anemometer around the pole so that its round end fits in
the top groove of the side of the rain collector side’s plastic mounting base. The
groove is right above two large holes.
2. While holding the mounting base of the rain collector against the pole, place the
two ends of the remaining U-bolt around the pole and through the two holes in
the base.
3. Slide the metal backing plate over the bolt ends as they stick out over the rain
collector base. Secure the metal backing plate with a lock washer and hex nut
on each of the bolt ends as shown previously.
Note: Do not tighten the hex nuts yet. Leave the hex nuts loose to swivel the ISS base on the pole.
4. The two ends of the anemometer’s U-bolt should now be pointing away from
the mounted rain collector side. Slide the anemometer’s mounting base over the
protruding bolt ends.
5. Place a flat washer, a lock washer and a hex nut on each of the bolt ends as
shown above. Do not tighten the nuts yet.
6. Raise the ISS unit to the desired height on the pole and swivel it so the
anemometer arm is pointing north.
7. Using an adjustable wrench or 7/16" wrench, tighten all four hex nuts until the
ISS is firmly fastened on the pole.
8. Re-attach the rain collector cone by setting the cone back on the base so its
latches slide downward into the latch openings on the base, then rotate the cone
clockwise.
Option 2: Installing ISS and Anemometer Separately
1. While holding the mounting base against the pole, place the two ends of a U-
bolt around the pole and through the two holes in the base.
2. Slide the metal backing plate over the bolt ends as they stick out toward the rain
collector cone. Secure the metal backing plate with a washer, a lock washer, and
a hex nut on each of the bolt ends. Do not tighten the nuts yet.
3. For the wireless ISS, swivel the ISS base so the solar panel is facing south (in
the Northern Hemisphere), or north (in the Southern Hemisphere).
4. Tighten the hex nuts using an adjustable wrench or 7/16" wrench.
5. Re-attach the rain collector cone.
6. Set the cone back on the base so its latches slide downward into the latch
openings on the base. Rotate the cone clockwise.
7. While holding the mounting base against the pole, place a U-bolt around the
pole and through the two holes in the base.
8. Place a flat washer, a lock washer and a hex nut on each of the bolt ends.
9. Swivel the anemometer until the arm is pointing north. The anemometer is
factory calibrated to report the correct wind direction when the anemometer arm
is aiming north. If you cannot install the anemometer with the arm aiming
Securing the ISS on the Tripod
6
north, see your Vantage Pro2 Console Manual for instructions on how to
calibrate the console to display the correct wind direction.
10.Using an adjustable wrench or 7/16" wrench, tighten the hex nuts.
Securing the ISS on the Tripod
Now the ISS is firmly attached to the anemometer extension tube.
1. Insert the swaged end of the
anemometer extension tube
down into the long
extension tube in tripod.
2. Consulting a compass or
local map, turn assembly
until the anemometer arm
points directly north.
3. Place the U-bolt provided
with the tripod around the
tubes where they overlap.
Secure the saddle onto the
U-bolt with the flat
washers, lock washers, and
hex nuts as shown.
4. Tighten the hex nuts quite
firmly, until the U-bolt
begins to dent the tubing
slightly. We recommend the
use of a torque wrench with
25 lb-ft of pressure to fasten the hex nuts.
The support tube should be crimped on the extension tube securely to prevent
any rocking or rotating.
Note: Do not use over 25 lb-ft torque wrench as it may damage the U-bolts.
Long Extension Tube
(secure in the tripod)
5/16"
5/16" Lock
Washers
5/16" Flat
Washers
Saddle
Tighten until
5/16" x 1-1/2" U-bolt
dents the tubing slightly
1 1/4"
Support Tube
(swaged end pointing
downward)
ISS
Heavy Duty
Hex Nuts
Attaching a Vantage Connect or Universal Shelter
7
Attaching a Vantage Connect or Universal Shelter
Install a Vantage Connect, Universal Shelter, or Solar Power Kit shelter to the
tripod the same way you would an ISS assembly.
5/16
"
Heavy
Duty
Hex
Nuts
Lock
Washers
Flat
Washers
1-1/8"
Saddle 1-1/2" x 5/16" U-Bolts;
tighten until bolts dent
tubing slightly
1 1/4"
Long
Extension
Tube
Support
Tu b e
5. We recommend the use of a torque wrench with 25 lb-ft of pressure to fasten the
hex nuts.
The support tube should be crimped on the extension tube securely to prevent
any rocking or rotating.
Note: Do not use over 25 lb-ft torque wrench as it may damage the U-bolts.
Mounting Tripod Kit Installation Manual
Product Number: #7716
Document number: 7395.299 Rev. H (6/4/14)
This product complies with the essential protection requirements of the EC EMC Directive 2004/108/EC.
Vantage Pro and Vantage Connect are registered trademarks of Davis Instruments Corporation, Hayward, CA.
© Davis Instruments Corp. 2014. All rights reserved. Davis Instruments Quality Management is ISO 9001 certified.
Information in this document is subject to change without notice.
3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.
510-732-9229 • Fax: 510-732-9188
®
Contacting Davis Instruments
If you have questions about installing your weather system on a tripod or
encounter problems installing a weather station on the tripod, please contact Davis
Technical Support. We’ll be glad to help.
Note: Please do not return items to the factory for repair without prior authorization.
(510) 732-7814 – Monday – Friday, 7:00 a.m. – 5:30 p.m. Pacific Time.
(510) 670-0589 – Technical Support Fax.
www.davisnet.com – Davis Instruments website. See the Weather Support section
for copies of user manuals, product specifications, application notes, and
information on software updates. Watch for FAQs and other updates.
Inhaltsverzeichnis
Andere DAVIS Kamerazubehör Handbücher
