DCS PHFS-P4 Installationsanleitung
1
THE FREE STANDING PATIO HEATER
Use and Care and Installation Guide
MODEL:
PHFS-P4
1
Thank you for selecting the DCS Patio Heater by Fisher & Paykel. Because of this appliance’s unique features we
have developed this Use & Care and Installation Guide. It contains valuable information on assembly instructions
and how to properly operate and maintain your new appliance for years of safe and enjoyable use.
To help serve you better, please fill out and submit your Product Registration by visiting our website at
www.dcsappliances.com and selecting “Customer Care” on the home page, then select “Product Registration”. In
addition, keep this guide handy, as it will help answer questions that may arise as you assemble and use your
new appliance.
For your convenience, product questions can be answered by a DCS Customer Care Representative by phone:
NOTE:Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper
and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.
DO NOTdiscardany packing material (box, pallet, straps) until the unit has been inspected.
WARNING!
Improper installation, adjustment, alteration, service or maintenance can cause property damage,
injury or death. Read the installation, operating and maintenance instructions thoroughly before
installing, using or servicing this equipment.
WARNING!
Ifthe information in this manual is not followed exactly, a fire or explosion may result causing
property damage, personal injury or death.
WARNING
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
DANGER
IfYou Smell Gas:
1. Shut off gas tothe appliance.
2. Extinguish any open flames.
3. If odor continues, immediately call your gas supplier or your fire department.
WARNING! For outdoor use only
WARNING!
Do not trylighting this appliance without reading the “Lighting Instructions” section of this manual.
This outdoor gas appliance is not intended to be installed in or on recreational vehicles , boats or in a
non-ventilated room. For outdoor use only.
AMESSAGE TO OUR CUSTOMER
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NOTE: Please write the Model, Code, and Serial Numbers on this page for reference (can be found on the right
side of the cabinet interior).
MODEL NUMBER CODE SERIAL NUMBER
2
SAFETY PRACTICES AND PRECAUTIONS 3
RECOMMENDATIONS ON HOOKUP TO GAS SUPPLY
Natural Gas Hookup 4
LP Gas Hookup 4
FEATURES 5
ASSEMBLY TOOLS & FASTENERS 6
ASSEMBLY INSTRUCTIONS 7-10
GAS LEAK TEST 11
LOCATING HEATER FOR USE 12
LIGHTING AND SHUTDOWN
LP Operation 13
Natural Gas Operation 14
STORAGE AND INSECT WARNING 15
TROUBLESHOOTING 16-17
SERVICE 18
WARRANTY 19-20
CONTENTS
3
■
Read and become familiar with the entire manual.
■
Do not use in an explosive atmosphere, keep heater away from areas where gasoline or other flammable liquids
or vapors are stored or used.
■
Before each use, check for damaged parts such as hoses, regulators, pilot or burner.
■
Do not attempt to alter unit in any manner, ie: shorten post length, bypass safety valve or operate heater without
the reflector.
■
Heater must always be placed on a hard and level surface.
■
Always maintain proper clearance to combustible materials. (Top =19’’; sides and rear =27”), see page 12.
■
Never replace or substitute the regulator with any other regulator other than a factory suggested replacement.
■
Itis imperative that the control compartment, burners, and circulating air passageways of the heater be kept
clean. The heater should be inspected before each use, and at least annually by a qualified service person, for
the presence of spiders, webs or other insects. The burner area is a common and desired spider haven. Spider
webs can present a dangerous condition which can damage the heater and render it unsafe for use.
CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING CONDITIONS EXIST
1. The smell of gas in conjunction with extreme yellow tipping of the burner flames.
2. The heater does not reach temperature.
3. The heater glow is excessively uneven.
4. The burner makes popping noises during use (a slight popping noise is normal when the burner is extinguished).
■
Installation must be carried out in accordancewith local regulations in force.
■
Do not clean heater with combustible or corrosive cleaners.
■
Do not use if wind velocity is greater than 10 miles per hour, because of flame-out possibility.
■
To avoid the risk of burns or accidental clothing ignition, do not touch the heater anywhere near the burner
assembly during operation.
■
Donot touch the burner assembly or reflector shield until after the heater has cooled for a minimum of 20 min-
utes after use.
■
Carefully monitor young children in the vicinity of the heater, especially when it is in operation.
■
Never connect an unregulated gas supply.
■
Always ensure that there is ample fresh air ventilation. This unit is for outdoor use only.
■
CALIFORNIA PROPOSITION 65-WARNING: The Burning of gas cooking fuel generates some by-products which
are on the list of substances which are known by the State of California to cause cancer or reproductive harm.
California law requires businesses to warn customers of potential exposure to such substances. To minimize
exposure tothese substances, always operate this unit according to the Use and Care Guide, ensuring you
provide good ventilation when cooking with gas.
■
This outdoor appliance is not intended to be installed in or on recreational vehicles and/or boats.
SAFETY PRACTICES & PRECAUTIONS
4
NATURAL GAS HOOKUP
The gas supply connections should be made by a qualified technician and in
accordance with local codes or ordinances. In the absence of a local code, the
installation must conform to the latest edition of National Fuel Gas Code
ANSI 223.1.
Amanual shut-off valve must be installed external to the appliance, in an
accessible location from the front for the purpose of shutting off the gas
supply (Fig.01). Any excess internal supply line must not protrude beyond the
back of the unit. Make sure the gas supply is turned off at the wall valve
before connecting the appliance. Make regulator connection as close to the
internal flex tube as possible. If the natural gas heater is intended to be
mobile, we recommend using a strain relief cord to ensure the gas line will not
be stressed.
Note:
This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of
Massachusetts.
LP GAS HOOKUP
The heater comes equipped with a regulator/hose assembly for connection to a standard Type 1 valve with an
OPD 20 lb. / 5 gallon LP gas tank (not included) and 2 straps to secure the tank within the base. A dented or
rustyLPtank maybe hazardous and should be checked by your LP supplier.
Never use an LP tank with a damaged valve. The LP tank must be arranged to provide for vapor withdrawal from
the operating cylinder.
The heater is designed tohouse a 20 lb./5gallon gas cylinder in the base assembly. Never connect an unregu-
lated LP tank to the heater. Never substitute gases without first converting the heater with a factory supplied
conversion kit. Conversion kits areavailable through customer service and must be installed by a qualified tech-
nician.
TOCONNECT LP CYLINDER TO THE HEATER
Open the door,and connect LP regulator assembly to the tank valve. The regulator and the tank have right-
handed threads (clockwise to tighten; no pipe sealer or teflon tape is required). When tightening, be careful not
to put too much force on the cylinder valve. Place the cylinder into the housing.
RECOMMENDATIONS ON HOOKUP TO GAS SUPPLY
A. Connect LP regulator assembly to the tank valve (Fig. 02).
B. Check regulator connections to the LP tank and to the flex tube for leaks. Tighten connections if necessary.
Place tank into the cabinet. Fix the tank position using two straps (Fig.03).
Gas Hook-up with shut-off valve
FIG. 01
FIG. 02 FIG. 03
5
■
Weather Resistant
■
All High Heat Parts Made Of Stainless Steel
■
Uniform Heat Pattern
■
Flame Out Protection Safety Control Valve
■
Durable Non-Slip Wheels
■
Weighted Base For Stability
■
Low Maintenance
■
Electronic Spark Ignition
■
Easy Access Door With Positive Latch
■
Heats 16’-20’ Diameter Area
■
Large Stainless Steel Emitter Grid
■
Uses 5 Gallon 20 lbs. LP Tank (not included)
■
Models Available For Natural Gas Or LP; Field Convertible
■
40,000 Btu Burner
FEATURES
6
ASSEMBLY TOOLS & FASTENERS
Tools Required:
PATIO HEATER COMPONENTS
PICTORIAL DESCRIPTION QTY
Reflector 1
Post 1
Head Assembly 1
Cabinet 1
Knob 1
Rubber Ring 1
Ring, Reflector 1
Retainer Bracket 1
FlatWasher 2
Tank Strap 2
LP Regulator (LP Heater only )
(connected) 1
Natural Gas Regulator
(Nat. Heater only) 1
Hex Screw 1/4 - 20 x 3/4” 6
Split Washer 1/4” 3
Button Head Screw 1/4 - 20 x
1/2” 3
Use & Care & Installation
Manual 1
Wrench or Socket 7/16”(1 pc),
3/4”(1 pc), 7/8” (1 pc)
5/32” Allen Wrench (1 pc)
Power Screwdriver or
Variable Speed Drill with
Phillips -tip #2 Attachment
Gloves
7
ASSEMBLY INSTRUCTIONS
CAUTION:
Some parts have sharp edges; care must be taken when handling the various components to avoid injury. Please
read safety information provided in these instructions before beginning assembly. Wear gloves when handling.
STEP 1 POST INSTALLATION
A. Insert post into the cabinet top. The threaded
hole should be oriented toward the front (door).
B. Install rubber ring (F) over the post.
STEP 2 INSTALLING THE PATIO HEATER
HEAD
A. Remove four #10 screws holding the valve
panel using Phillips screwdriver and set them
aside.
B. To get access to ignition wires, disengage (gently
pull on wires) the valve panel and head body. Dis-
connect ignition wires from igniter, remove valve
panel.
8
C. Straighten the flex tube. Insert regulator and
flex tube into the post. Slide patio heater head
over the post. Align 3 head holes with thread-
ed post holes.
D. Attach patio heater head to the post using
3button head screws (P) with 5/32” Allen
wrench.
ASSEMBLY INSTRUCTIONS
E. Attach the post to the cabinet using bracket (H),
and Hex screw 1/4-20 x 3/4 (M). Add two more
Hex screws 1/4-20 x 3/4 (M), and two Flat washer
0.313 (I) on each side of the sleeve. Slide flex hose
into center of retainer bracket. Ensure the post is
vertical before tightening the screws.
Andere Handbücher für PHFS-P4
1
Inhaltsverzeichnis
Sprachen:
Andere DCS Terrassenheizung Handbücher
Beliebte Terrassenheizung Handbücher anderer Marken
Lava Heat
Lava Heat Venetian Bedienungsanleitung
EHS Ltd.
EHS Ltd. HQH-2000W Bedienungsanleitung
VONROC
VONROC ALICUDI PH515AC Bedienungsanleitung
OZONA
OZONA Heatflow IF010997 Bedienungs- und Wartungshandbuch
theBBQshop
theBBQshop 51611010 Einrichtungshandbuch
Endless Summer
Endless Summer EWTS9151M Bedienungsanleitung