decon Adventus Kurzanleitung
Adventus Folding wheelchair
adaptor
Assembly Instructions
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
2
1. Overview
Picture1
A Holder adapter bar
B QR-pin
C Adapter bar
D Fork adapter bar
E Adjustment tool
E
C
A
B
D
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
3
2. Mounting of adapter bar
First mount the holder (A). The shape of the holder can vary depending on wheelchair model.
Mount the holders so that they still can be moved along the wheelchair chassis. Now mount
the adapter bar (C) into the holders (A) by using the QR-Pins (B).
Make sure the ends of the adapter bar (C) are parallell otherwise it can be hard to assemble it
into the holders (A).
Now tighten the screws in the holders (A) so that it grips the wheelchair chassis.
Picture2&3, Universal holder for wheelchairs with round tubing
Picture4&5, Holder for Etac Cross/Cross5
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
4
Picture6, Holder mounted on both sides
Picture7, Mount the adapter bar into the holders using the QR-pins
Picture8, Mounted adapter bar
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
5
3. Adjustment of adapter bar
Step 3.1
Mount the adjustment toll onto the fork (D). Remove the screws in the fork that locks the
rotation (see picture bellow). Also make sure that the fork sits in the center of the wheelchair.
Picture9, Universal holder for wheelchair with round tubing chassis
Picture10
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
6
Step 3.2
Now rotate both the adapter bar and the fork to a position where the adjustment tool shows
the correct angle and the fork doesn’t collide with the footrests. If possible, make sure that
the fork doesn’t sit lower than the footrest and that the height, if possible, corresponds to the
picture bellow.
Picture11
Picture12
=
Approx. 30mm
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
7
Step 3.3
Reassemble the screw in the hole that is fits the best, se picture bellow for example.
Picture13
Adventus Folding wheelchair adaptor, Assembly Instructions Rev0
__________________________________________________________________________________
8
Step 3.4
Now tighten the screws that sits in the clamp of the adaptor bar. Slightly tighten all four
screws on the clamp. It is important to not completely tighten each screw, but to slowly
tighten all four, a little at a time. Keep tightening until all four screws are secured (30-35Nm
of torque). Also make sure one last time that the fork is centered and the angle of the
adjustment tool is still correct.
Picture14
Step 3.5
Check one last time that all screws are properly secured. Now see the user manual of
Adventus to continue the installation. This can be downloaded from www.decon.se/en/.
Andere Handbücher für Adventus
1
Inhaltsverzeichnis
Andere decon Rollstuhl Handbücher
decon
decon ADV5X02 Bedienungsanleitung
decon
decon Gearwheel GWl0S0 Bedienungsanleitung
decon
decon Flexlife D9 Bedienungsanleitung
decon
decon Liberty LBM7013 Bedienungsanleitung
decon
decon Infinity Bedienungsanleitung
decon
decon E-Move MEM20 Bedienungsanleitung
decon
decon JW Smart Tune Bedienungsanleitung
decon
decon Gearwheel Bedienungsanleitung
decon
decon INFM7002 Bedienungsanleitung
decon
decon Panthera S2/U2 Bedienungsanleitung
