DEFA BG600 Bedienungsanleitung

BG600

Bruksanvisning

Käyttöohje

User Manual

www.defa.com

Distributor Sweden

KG Knutsson AB

S-191 81 SOLLENTUNA

SVERIGE

Boat

Congratulations on buying a DEFA boat alarm

BG600 is an alarm system that contains GSM messaging and GPS positioning. The

alarm system is constructed for use in motor and sailing boats that have 12/24V elec-

trical systems. The integrated GSM module provides two-way communication between

the user and boat from another mobile telephone (SMS). DEFA authorises its boat

alarm installation technicians, and wish for them to be used to install our products in

order to protect users against problems that can occur when the installation work is

shoddy. The functions of the alarm and its electrical connections should be checked

once a year, in order to achieve reliable operations. It is important that you, as the boat’s

owner, read this manual carefully.

The BG600 is manufactured by DEFA AS, www.defa.com

TABLE OF CONTENTS

How to use your BG600 53

Turning on your alarm (activation) 53

Temporary disconnection of sensors 53

Turning off the alarm (deactivation) 54

Warnings from the alarm 57

Programming remote controls 57

Changing the batteries in the remote control 58

PIN codes 59

About commands 61

Trouble shooting 65

Technical speciﬁcations BG600 68

Boat

You operate your BG600 using the four buttons on the remote control. Button 1

activates and deactivates the alarm. It is also possible to activate / deactivate the

alarm from a common GSM mobile phone (see the chapter which discusses the GSM

phone).

The three other buttons can be used to control of

e.g. lights, deck lighting, heating, anchor winch, etc.

Short press means that you press for a maximum of

2 second. Long press means that you press for a minimum

of 2 seconds.

The remote control has a maximum range of 40 m.

The range can vary. Local radio disturbance can affect the range.

1.1 TURNING ON YOUR ALARM (ACTIVATION)

You activate the alarm with a short press on button 1.

The boat’s lights ﬂ ash once for 2 seconds. The LED on the PIN

code panel begins to ﬂ ash. The alarm is activated.

NB! The ignition must be OFF before you can activate the alarm.

NB! The alarm can only be triggered (sounding the alarm) ﬁ ve

seconds after activation.

The range can vary. Local radio disturbance can affect the range.

1. HOW TO USE YOUR BG600

1.2 TEMPORARY DISCONNECTION OF SENSORS

If you, for example, leave your dog on board the boat, you should disconnect the

motion sensor to avoid false alarms.

1.Turn OFF the ignition.

2. Depress the button on the PIN code panel and hold

it down until the LED lights.

3. Release the button (the LED extinguishes).

4. Activate the alarm.

The sensor will now be disconnected until the alarm is

turned off and the ignition turned on.

Button 1

Button 2

Button 3

Button 4

The alarm can only be triggered (sounding the alarm) ﬁ ve

Boat

1.5 EMERGENCY DEACTIVATION OF THE ALARM

Use the button on the PIN code panel to enter the four ﬁ gures on your PIN code card.

1. Turn on the ignition.

2. Press the button on the PIN code panel as many times as

the ﬁ rst ﬁ gure in the PIN code. (If the PIN code is, for

example: 3 – 1 – 5 – 2, ﬁ rst ﬁ gure is 3 and the button is

pressed 3 times).

3. Then wait while the LED lights to show that the

ﬁ rst ﬁ gure has been

4. Press the button on the PIN code panel as many

times as the second ﬁ gure in the PIN code, and

wait for receipt.

5. Continue in the same way for the third and fourth

ﬁ gures.

After the fourth ﬁ gure has been entered, the alarm will

turn off after a few seconds, as long as the correct PIN

code has been entered. If the wrong code is entered,

wait min. 10 sec. before trying again. Start at point 2.

1.4 TURNING ON YOUR ALARM (ACTIVATION)

You deactivate the alarm with a short press on button 1.

The boat’s lights ﬂ ash brieﬂ y twice. The LED on the PIN code

panel stops ﬂ ashing. The alarm is deactivated.

NB! It is important that an alarmed hatch is not opened, or the igni-

tion turned ON for 4 minutes after deactivation. See the chapter on

reactivation.

                      

            

                              

   

       

                     

Button 1

1.6 WARNINGS OF ALARMS TRIGGERED DURING

THE LAST PERIOD OF ACTIVATION

If the alarm has been trig-

gered since it last was acti-

vated, the alarm will warn

you when the ﬁ rst alarmed

hatch is opened following

deactivation. It warns you

with two short blasts of the

siren and/or horn.

Boat

When the ignition is turned off, the LED on the PIN code panel will

ﬂ ash in sequence (2,3,4 or 5 ﬂ ashes, depending on the type of alarm

input that is active) if a hatch is open, or if a sensor is active. This is to

prevent a boat being left with an open hatch, or with a faulty sensor.

Close all of the hatches and check that the LED is dark before activa-

ting the alarm.

If the LED ﬂ ashes in sequence, as described above, even when all of

the hatches are closed and the sensors inactive, contact your alarm

installer for assistance.

This warning disappears as soon as the alarm is activated, whether or

not the cause of the warning has been removed.

2 ﬂ ashes: the loop(s) for the magnetic contacts.

3 ﬂ ashes: inputs activated by grounding.

4 ﬂ ashes: inputs activated by 12/24V.

5 ﬂ ashes: 24 hour alarm input(s).

Open hatches or active sensors are also warned of by a short blast of

the siren/horn during activation (can be disconnected).

1.7 REACTIVATION

If you turn the alarm off, but do not open an alarmed hatch or turn on the ignition, the

alarm turns on again 4 minutes after deactivation. This is a function that protects against

inadvertant deactivation.

NB! The hatch does not have to remain open. It is enough to open and close the hatch,

because the alarm then “understands” that it had been deactivated on purpose. Turning

the ignition ON and OFF also prevents reactivation.

NB! If the BG600 alarm is connected to a BG300 immobilizer, the reactivation period for

the immobilizer is 2 min. The immobilizer will also turn itself on automatically 2 min. after

the boat’s ignition has been turned off. This means that the immobilizer may be on when

the alarm is off. The immobilizer deactivates when the alarm deactivates.

2. WARNING ABOUT OPEN HATCH OR ACTIVE SENSOR

2.1 IGNITION ALARM

An ignition alarm is when the alarm has been triggered because the ignition was turned

on while the alarm was activated.

Boat

2.3 ALARM TRIGGERED BY A MOTION SENSOR (ACCESSORY)

Alarm triggered by someone moving in the coverage area of the

motion sensor while the alarm was activated.

2.2 HATCH ALARM

A hatch alarm is when the alarm has been triggered by an alarmed hatch or door being

opened while the alarm was activated.

2 ALARM TRIGGERED BY A MAT CONTACT (ACCESSORY)

Alarm triggered by someone treading on a mat contact while the alarm was activated.

24 hour alarm sounding, whether the alarm is turned ON or OFF.

The alarm is connected to a water level sensor (standard) that monitors the water level

at a selected location in the boat. The alarm also monitors the voltage level in the boat’s

battery. Other external sensors/detectors can also be connected to 24 hour alarm inputs

on the alarm, including gas and smoke detectors.

Only one SMS with 24 hour alarms is sent per 24 hour alarm input per alarm activation.

In other words, when you receive a water level alarm, for example, the system will block

transmission of more water level alarms until the ignition is turned ON (does not have to

remain on) or the alarm is activated (does not need to remain activated).

The system does not, however, block warning of other alarms connected to other 24

hour alarm inputs (e.g. smoke and gas alarms).

If your receive an alarm – check the cause immediately. During fault ﬁ nding, the alarm

vvarning (separate output for warning 24 hour alarms) can be turned off for 5 minutes

by pressing button 1 on the remote control. When you do this all 24 hour alarm outputs

are turned off for 5 minutes. Your alarm installer can provide information about how the

24 hour alarms work on your boat.

3. 24 HOUR ALARM

If the boat is moved more than 100 metres with the alarm activated, a motion alarm can

be triggered. This alarm warns only via SMS and requires GPS as an accessory.

4. MOTION ALARM (REQUIRES ACCESSORIES)

Boat

All alarms are sent as SMS messages to selected mobile phone numbers

(maximum 3 pre-selected numbers). See also the chapter concerning the GSM

phone.

Alarms triggered by the ignition, hatches, mat sensors and motion sensors are

also warned by the lights ﬂ ashing for 5 minutes, as well as sounding the siren/

horn for 60 seconds. Only the motion alarm is warned by SMS.

Alarms triggered by sensors connected to the 24 hour alarm inputs on the alarm

are only warned by SMS, or by their own sirens/lights, depending on the installa-

tion. Emergency alarms are warned via SMS. They are sent to a separate optio-

nal mobile phone number

(a fourth pre-selected

number).

The alarm can be programmed to accept a maximum of 8 remote controls. When a new remote

control is programmed all of the remote controls to be used must be re-programmed. First check

that the alarm is deactivated and that the ignition is turned on! Use the button on the PIN code

panel to enter the four ﬁ gures on your PIN code card.

1. Turn off the alarm and turn the ignition on.

2. Press the button on the PIN code panel as many times as

the ﬁ rst ﬁ gure in your PIN code. (If the PIN code is, for example:

3 – 1 – 5 – 2, ﬁ rst ﬁ gure is 3 and the button is pressed 3

times).

3. Then wait while the LED lights to show that the ﬁ rst ﬁ gure has been

received.

4. Press the button on the PIN code panel as many times as

the second ﬁ gure in the PIN code and wait for the receipt.

5. Continue in the same way for the third and fourth ﬁ gures.

6. Press button 1 on the remote control that you want to programme, while the LED ﬂ ashes.

The LED lights steadily for 2 seconds as conﬁ rmation that the remote control has been

coded, before it begins to blink again.

7. Depress button 1 on the next remote control to be programmed (within 10 seconds).

Continue until all of the remote controls (max. 8) have been programmed.

8. Turn off the ignition.

9. Check that all of the remote controls can activate/deactivate the alarm.

         

              

                



    

the ﬁ rst ﬁ gure in your PIN code. (If the PIN code is, for example:

3. Then wait while the LED lights to show that the ﬁ rst ﬁ gure has been

5. ALARM WARNINGS

6. PROGRAMMING REMOTE CONTROLS

Button 1

Boat

The glass breakage sensor triggers the alarm if a window close to the

sensor is broken (requires toughened glass). The glass breakage sensor

is also ﬁ tted with ﬂ ashing diodes. These indicate the status of the alarm

in the same way as the LED on the PIN code panel. The glass breakage

sensor provides the option of seeing the alarm status, even from positions

from which the PIN code panel is not visible. A. Grey button, equivalent

to the yellow button on the PIN code panel. Lamp B lights if the glass

breakage sensor has been triggered. The light extinguished when the

boat’s ignition is turned on.

6.1 CHANGING BATTERIES IN THE REMOTE CONTROL

The remote control makes a noise when the buttons are pressed. The batteries can be tested

by holding button 1 down for more than 1 second. If the batteries contain enough power, the

sound will remain the same as long as the button is depressed. If the sound changes 1 second

after the button is pressed, the batteries should be replaced. They should be replaced within 14

days. The batteries have a normal lifetime of 1 year.

NB! The battery warning can also be triggered if the remote

control is stored cold. This is because batteries have lower

voltage levels in cold conditions.

The batteries are type CR 1220 and can be bought from boat

alarm installers or in photo shops or jewellers. The battery

compartment is opened by turning the cover clockwise (use

a coin) to “OPEN” (See the rear of the remote control). Take

out the old batteries and replace with new in the same way (+

towards the inside of the battery cover). Make sure that the

cover’s o-ring is in place around the inner edge before the

cover is replaced. Turn the cover back to the closed position.

     

     

     

        

7. GLASS BREAKAGE SENSOR (ACCESSORY)

The alarm can be supplemented with a back-up battery. In the case of sabotage that

results in loss of power or short circuit of the boat’s electrical system, the alarm will

continue to function for a short period using the back-up battery.

8. BACK-UP BATTERY (ACCESSORY)

Boat

                      

            

                              

   

       

                     

The system contains 3 PIN codes that are important to distinguish between:

PIN code 1: This PIN code is shown on the PIN code card and is used for emergency

deactivation of the system.

PIN code 2: The PIN code that comes with the

SIM card. Remember to turn off the PIN control

before the SIM card is installed in the central

unit. When you have done this you can forget

this code.

PIN code 3: This code acts as password when

you give commands through your mobile phone

(See the chapter about the GSM phone). This

PIN code is default 0000. Remember to change

this code (see GSM Telephone chapter)

HINT: You can change PIN code 3 to the same

as PIN code 1 to make it easier to remember.

This gives you only one PIN code to remember.

Remember to keep this PIN code unavailable

for unauthorised persons.

Important! The serial number on the central unit will allow DEFA to ﬁ nd PIN code 1

if you should lose it or forget it. If you choose to change PIN code 3 to something dif-

ferent from PIN code 1, then you are the only person to know this code, and if you lose

it you will not be able to use your mobile phone to control your alarm!

NB! When a command is sent from your mobile phone it is stored in “sent messages”.

Be careful with your mobile phone as this can now also contain your code. The mobile

phone can be used as a remote control for your boat alarm.

9. PIN CODES

Boat

NB! All communiction with the alarm is by SMS. When an alarm is triggered, an SMS message

is sent to a pre-selected mobile number. A maximum of 3 different mobile numbers can receive

messages at the same time.

It is also possible to activate/deactivate the alarm using SMS, as well as checking the status of

the alarm and receiving an answer by SMS:

Is the alarm activated or deactivated? Are the sensors connected or disconnected? What is the

temperature on board the boat? What is the boat’s battery voltage? What is the boat’s position,

where in the world is it (requires GPS)?

It is possible to activate a maximum of four control outputs by

SMS (depending on how the alarm is installed). E.g. to turn on

the boat’s heaters.

NB! In order to be able to communicate with the alarm by SMS,

you must install an SMS card in the alarm. If you use a top-up

card in the alarm, you must remember that certain telephone

providers require the card to be topped up at least once per

year. As the SMS function will not work with an empty card, the

balance on the card must be regularly checked.

NB! When the SIM card has been acquired, the PIN control must

be turned off before the card is installed in the alarm central unit.

You do this by ﬁ rst installing the SIM card in a mobile phone,

then selecting PIN control OFF. The method depends on the

telephone being used. You will ﬁ nd the method in the user guide

for the mobile phone.

Security code (PIN code 3):

All commands begin with this code, so that unauthorised persons

cannot gain access to your boat via SMS. The default code

from the factory is four zeroes (0000). Remember to change

this code as quickly as possible after installation of the alarm

(see changing the security code). The PIN code must contain 4

characters, ﬁ gures and/or letters.

Important! Read the chapter about PIN codes before you change this code.

NB! The alarm is caps sensitive. If you have changed your PIN code from 0000 to e.g. CODE,

you must enter KCDE as the PIN code in your commands. If you enter the PIN code with lower

case letters it will not work.

         

              

                



10 GSM PHONE

Inhaltsverzeichnis

Andere DEFA Sicherheitssystem Handbücher

DEFA

DEFA Magnet Contact Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung