Deif CIO 308 Bedienungsanleitung

INSTALLATION AND COMMISSIONING GUIDE

CAN bus-based I/O module, CIO 308

8 multi-inputs

• Mounting

• Terminals and wiring

• Commissioning, using the utility software

DEIF A/S · Frisenborgvej 33 · DK-7800 Skive

Tel.: +45 9614 9614 · Fax: +45 9614 9615

[email protected] · www.deif.com

Document no.: 4189341078D

SW version: 1.10.0

1. Introduction

1.1 Warnings, legal information and safety.........................................................................................................................................................................3

1.1.1 Warnings and notes.......................................................................................................................................................................................................... 3

1.1.2 Legal information and disclaimer.................................................................................................................................................................................3

1.1.3 Safety issues........................................................................................................................................................................................................................3

1.2 About the installation and commissioning guide.................................................................................................................................................... 4

1.2.1 General purpose.................................................................................................................................................................................................................4

1.2.2 Intended users.....................................................................................................................................................................................................................4

1.2.3 Contents and overall structure......................................................................................................................................................................................4

2. Installation, mounting and wiring

2.1 Installation..................................................................................................................................................................................................................................... 5

2.2 Mounting.........................................................................................................................................................................................................................................5

2.2.1 Mounting the CIO modules............................................................................................................................................................................................ 5

2.2.2 Dimensions........................................................................................................................................................................................................................... 5

2.3 Common functions....................................................................................................................................................................................................................6

2.4 Wiring and terminals................................................................................................................................................................................................................8

2.4.1 Terminal overview CIO 308............................................................................................................................................................................................8

2.4.2 CIO 308 wiring.................................................................................................................................................................................................................. 11

2.4.3 CAN bus...............................................................................................................................................................................................................................11

3. Communication

3.1 Communication setup...........................................................................................................................................................................................................14

3.1.1 Step-by-step guide to setting up communication the first time.....................................................................................................................15

3.1.2 Step-by-step guide to update firmware to CIO module................................................................................................................................... 15

4. I/O setup

4.1 CIO info tab.................................................................................................................................................................................................................................16

4.2 Status relay.................................................................................................................................................................................................................................16

4.3 Multi-input....................................................................................................................................................................................................................................18

4.3.1 Setting up a multi-input................................................................................................................................................................................................. 18

4.3.2 Thermocoupler with cold junction compensation............................................................................................................................................... 20

4.3.3 Wire fail detection............................................................................................................................................................................................................21

4.3.4 Change text in the display............................................................................................................................................................................................23

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 2 of 24

1. Introduction

1.1 Warnings, legal information and safety

1.1.1 Warnings and notes

Throughout this document, a number of warnings and notes with helpful user information will be presented. To ensure that these are

noticed, they will be highlighted as follows in order to separate them from the general text.

Warnings

DANGER!

This highlights dangerous situations. If the guidelines are not followed, these situations could result in death, serious

personal injury, and equipment damage or destruction.

CAUTION

This highlights potentially dangerous situations. If the guidelines are not followed, these situations could result in personal

injury or damaged equipment.

Notes

INFO

Notes provide general information, which will be helpful for the reader to bear in mind.

1.1.2 Legal information and disclaimer

DEIF takes no responsibility for installation or operation of the generator set. If there is any doubt about how to install or operate the

engine/generator etc. controlled by the specific extension, the company responsible for the installation or the operation of the

extension must be contacted.

DANGER!

The CIO module is not to be opened by unauthorised personnel. If opened anyway, the warranty will be lost.

Disclaimer

DEIF A/S reserves the right to change any of the contents of this document without prior notice.

The English version of this document always contains the most recent and up-to-date information about the product. DEIF does not

take responsibility for the accuracy of translations, and translations might not be updated at the same time as the English document.

If there is a discrepancy, the English version prevails.

1.1.3 Safety issues

Installing and operating the CIO module may imply work with dangerous currents and voltages. Therefore, the installation should

only be carried out by authorised personnel who understand the risks involved in working with live electrical equipment.

DANGER!

Be aware of the hazardous live currents and voltages. Do not touch any live inputs as this could lead to injury or death.

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 3 of 24

1.2 About the installation and commissioning guide

1.2.1 General purpose

This installation and commissioning guide mainly includes general product and hardware information, mounting instructions, terminal

strip descriptions, I/O lists and limits, wiring descriptions and how to produce translations for the CIO module through the USW.

The general purpose of this document is to give the user important information to be used in the installation of the unit.

DANGER!

Please make sure to read this document before starting to work with the CIO module and the controller. Failure to do this

could result in human injury or damage to the equipment.

1.2.2 Intended users

This installation and commissioning guide is mainly intended for the person responsible for the design and installation. In most

cases, this would be a panel builder designer. Naturally, other users might also find useful information in the document.

1.2.3 Contents and overall structure

This document is divided into chapters, and in order to make the structure simple and easy to use, each chapter will begin from the

top of a new page.

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 4 of 24

2. Installation, mounting and wiring

2.1 Installation

Installation

The CIO module is delivered in a sturdy carton to prevent shipping damage. When you receive a system, check the part number

against that of the requisition and packaging list for agreement. Inspect for damage, and if there is evidence of such, immediately file

a claim with the carrier and notify the regional DEIF sales office, your sales representative or a sales representative at DEIF's head

office in Skive, Denmark.

If the unit is not installed immediately, store it in the original shipping package in a moisture and dust free environment.

2.2 Mounting

2.2.1 Mounting the CIO modules

The CIO module is designed for mounting in a closed cabinet on a DIN rail. The module can be mounted on either a TS35 or G-type

rail. The unit must be mounted where the ambient temperature does not exceed the range -40 to +70 ⁰C.

2.2.2 Dimensions

The CIO 308 module dimensions are presented here in mm (inches):

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 5 of 24

2.3 Common functions

1. LED1 (Status LED)

LED1 indicates the operation status of the module, and the status output of this LED is located at terminal 3-4.

Set up as either status or configurable relay:

Set up as status relay

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 6 of 24

LED colour Description

Green Status is OK, the relay is closed.

Red constant The CIO module is not working correctly, the relay is open.

Red flashing ID 0 is selected, relay is open.

Set up as configurable relay

LED colour Description

Green Status is OK, the relay is closed.

Turned off/no light Status is OK, the relay is open.

Red constant The CIO module is not working correctly, the relay is open.

Red flashing ID 0 is selected, relay is open.

Yellow The relay is closed, status is not OK.

2. Terminal resistor

The CIO module has a built-in 120 ohm end-termination for the CAN bus line which can be activated via the switch (S1) located at

terminal 5. See the section "CAN bus" in "Wiring and terminals" for more information and to see when to activate the switch.

3. LED2 (CAN bus LED)

LED2 indicates the status of the CAN bus communication to the host controller. This LED is located at terminal 7.

LED colour Description

Green constant Communication to the controller is working correctly.

Red constant No CAN bus communication detected.

Red 2 flashes CAN bus communication detected, but no CIO-specific

communication

Red flashing CIO communication detected, but not to this module.

4. ID selector

The ID selector is used to give CIO modules of the same type different IDs.

CIO 116 can use IDs from 1 to 15

CIO 208 can use IDs from 1 to 15

CIO 308 can use IDs from 1 to 15

5. USB for firmware update

The firmware of the CIO modules can be updated via the USB port.

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 7 of 24

2.4 Wiring and terminals

2.4.1 Terminal overview CIO 308

Terminal Name Description Comment

1 + +12/24 V DC

Power supply

2 - 0 V DC

Status

Common

Status output (configurable)

4 Normally open

5 H CAN-High

CAN bus interface 6 Com CAN-Common

7 L CAN-Low

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 8 of 24

Terminal Name Description Comment

Input A

Multi-input 8

Multi-input group 1

9 Input B

10 Input C

I11

Input A

Multi-input 11 12 Input B

13 Input C

I14

Input A

Multi-input 14

15 Input B

16 Input C

I17

Input A

Multi-input 17 18 Input B

19 Input C

I20

Input A

Multi-input 20

Multi-input group 2

21 Input B

22 Input C

I23

Input A

Multi-input 23 24 Input B

25 Input C

I26

Input A

Multi-input 26 27 Input B

28 Input C

I29

Input A

Multi-input 29

30 Input B

31 Input C

Input LED

Each multi-input has its own LED, and the table below illustrates when the LED is on/off.

Input type LED Description

Digital input

On Input is active

Off Input is inactive

0(4) to 20 mA

On Within input range 4 to 20 mA

Off

Outside input range 4 to 20 mA (LED is

flashing when in protection mode: >30

mA)

0 to 10 V

On Within input range 0.2 to 10 V

Off Outside input range 0.2 to 10 V

RMI

On Within input range 10 to 2500 Ω

Off Outside input range 10 to 2500 Ω

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 9 of 24

Input type LED Description

Pt100 sensor

Within selected input range (Low range

-50 to 250°C or high range: -200 to

850°C)

Off

Outside selected input range (Low range

-50 to 250°C or high range: -200 to

850°C)

Pt1000 sensor

Within selected input range (Low range

-50 to 250°C or high range: -200 to

850°C)

Off

Outside selected input range (Low range

-50 to 250°C or high range: -200 to

850°C)

Thermocouple

On Within input range of selected type of

thermocouple

Off Outside input range of selected type of

thermocouple

INSTALLATION AND COMMISSIONING GUIDE 4189341078D EN Page 10 of 24

Andere Handbücher für CIO 308

Inhaltsverzeichnis

Andere Deif Steuereinheit Handbücher

Deif

Deif Delomatic 4 AOP-2 Leitfaden

Deif

Deif GCU 100 Bedienungsanleitung

Deif

Deif Multi-line 2 Bedienungsanleitung

Deif

Deif GPC-3 Hydro Bedienungsanleitung

Deif

Deif DELOMATIC 4 Series Beilage

Deif

Deif GCU 100 Bedienungsanleitung

Deif

Deif Multi-line 2 Bedienungsanleitung

Deif

Deif PPU 300 Bedienungsanleitung

Deif

Deif PCM 4 Series Leitfaden

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung