Dell PowerEdge M420 Bedienungsanleitung
Dell and the Dell logo are
trademarks of Dell Inc.
Dell 10GbE Pass Through Module (XAUI)
User Manual
P/N: M1601P
Rev 1.0
16 Port Pass Through Module
Document Number: 3192
Rev 1.0
2
____________________
Information in this document is subject to change without notice.
© 2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.;
Other trademarks and trade names may be used in this document to refer to either the entities claiming the mark and names or their
products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
July 2010 Rev: A00
Dell -10GbE PTM Rev 1.0
3
Table of Contents
Intended Audience 5
Conventions 5
Chapter 1 Overview 6
1.1 Features 6
1.2 Serial Number and Product Version Information 7
Chapter 2 Installation and Basic Operation 8
2.1 Unpacking the Pass Through Module 8
2.2 Insertion and Removal of the PTM 8
2.2.1 PTM Insertion 8
2.2.2 PTM Removal 9
2.3 Connecting the External Ports 9
2.3.1 10 Gigabit Ethernet SFP+ Modules 9
2.3.2 Installation and Removal of Optical Transceiver Modules 9
2.4 LED Indicators 10
2.4.1 System LEDs 10
2.4.2 Port LEDs 10
2.4.3 Installation Safety Warnings 12
2.4.4 Mechanical Installation 13
2.4.5 Cable Installation 13
Chapter 3 Troubleshooting 14
Appendix A Specifications 15
A.1 Mechanical Drawing with Dimensions 16
Appendix B Supported Optical Modules and DCAs 17
Appendix C EMC Certification Statements 18
C.1 FCC Statements (USA) 18
C.2 ICES Statements (Canada) 19
C.3 VCCI Statements (Japan) 19
C.4 KCC Certification (Korea) 19
Appendix D Interface Connector Pinouts 21
D.1 SFP+ Interface 21
Rev 1.0
4
Related Documentation
The documentation set accompanying the Pass Through Module includes the following:
Table 1 - Reference Documents and Web Sites
Firmware and Firmware Update Tools
Dell Pass Through Module Software User Manual
Latest Supported Cables and Optical Modules
Dell -10GbE PTM Rev 1.0
5
About this Manual
This User Manual is for the Dell 10Gb Ethernet Pass Through II passs through module.
This manual describes the installation and basic use of Dell 10GbE 16 port Pass Through Module
for blade servers.
Intended Audience
This manual is intended for users and system administrators responsible for installing and setting
up the Dell 10GbE 16 port Pass Through Module for blade servers.
Conventions
The terms downlink (internal–from servers) and uplink (external–out to the world) are used
throughout the document. Downlink refers to server connections through the backplane where
Ethernet is used. Uplink refers to the outside network, where a different Ethernet protocol is used.
The term PTM is used to indicate the Dell 10GbE 16 port Pass Through Module.
Caution: This symbol indicates the possibility of physical injury to the user or
installer.
OverviewRev 1.0
6
1 Overview
The PTM is an I/O module designed for the PowerEdge M1000e Dell Chassis. The product pro-
vides 10Gigabit connectivity for blade servers to Ethernet LANs. The product supports the follow-
ing Ethernet protocols.
Each front panel port provides connectivity to the blade with the corresponding number in the
chassis.
Figure 1: Pass Through II Front Panel
1.1 Features
The PTM feature set includes:
Internal Links
• 16 links of 10Gb Ethernet through the backplane
External links
• 16 SFP+ front panel ports of 10Gb Ethernet
IEEE and Other Ethernet Standards Compliance
• IEEE 802.3ae 10Gigabit Ethernet support
• IEEE 802.3ap Ethernet Operation over Electrical Backplanes
• Jumbo Frames up to 9K support
Connectors and Cabling
• Twin Axial Pair connector
• Optical modules for SR and LR
• All ports support active cables
Front Panel Indicators
• Per port status LEDs: Link Up, Link Activity
Table 2 - Protocols
Physical Connections Pass Through II Protocol
Blade Servers to PTM (Internal
Links)
XAUI
Front Panel Ports (External Links) 10G XFI
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
D
D
D10 Gb Ethernet Pass Through II
Dell -10GbE PTM Rev 1.0
7
• System status LEDs: Power Supply, Status
1.2 Serial Number and Product Version Information
The serial number and product version information are found on the label seen in the figure below.
Figure 2: Generic Product label
S/N: IL0HCC2D215463325875
P/N: 0HCC2D
Rev: X1
Installation and Basic OperationRev 1.0
8
2Installation and Basic Operation
2.1 Unpacking the Pass Through Module
Before you install your new PTM, unpack it and make sure that there is no visible damage that
may have occurred during shipping. Your package should contain the following items:
• Dell -10GbE Pass Through Module for Blade Servers
• This User’s Manual
The PTM is shipped without optical modules.
If anything in the package is damaged or missing, please contact your customer representative
immediately.
2.2 Insertion and Removal of the PTM
The Dell 10Gb Ethernet Pass Through II may be plugged into fabric slots B1, B2, C1, and C2.
Determine which slot to use, based on desired system configuration.
2.2.1 PTM Insertion
Insert the PTM into the chassis as shown in the following diagram:
Figure 3: Dell Chassis Slots for the PTM
Slot B1 Slot C1 Slot B2Slot C2
Dell -10GbE PTM Rev 1.0
9
The PTM supports hot-insertion into the chassis. If the PTM is inserted to a powered chassis, the
power LED (green) should turn on immediately.
2.2.2 PTM Removal
The PTM supports hot-removal. It may be removed when the chassis is powered on or off.
The PTM must not be removed during a firmware update process.
Note: Firmware update is in progress when the amber LED is blinking.
2.3 Connecting the External Ports
The PTM front panel presents 16 SFP+ ports. Each port provides connectivity to a server with the
respective number. Figure 4 shows the front panel view of the PTM.
Figure 4: Pass Through II Front Panel
2.3.1 10 Gigabit Ethernet SFP+ Modules
The PTM supports SFP+ modules for 10 Gigabit Ethernet, with 10GBASE-SR and 10GBASE-LR
PHYs. SFP+ modules must be approved for use with this PTM. Modules not approved may not
work. See Supported Optical Modules and DCAs on page 17 for lists of approved DCAs and opti-
cal modules.
2.3.2 Installation and Removal of Optical Transceiver Modules
Optical transceiver modules have a locking mechanism which can be opened or closed.
To insert the module into the cage:
1. Open the module’s locking mechanism.
2. Make sure that the male connectors on the module aligns with the female connector inside of
the cage. Also check that there is no dirt or foreign matter in the module or in the cage.
3. Insert the module into the adapter card module cage.
4. Close the locking Mechanism.
To remove the module from the cage:
1. Unlock the locking mechanism by opening the handle.
2. Pull the module out of the cage.
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
D
D
D10 Gb Ethernet Pass Through II
Installation and Basic OperationRev 1.0
10
2.4 LED Indicators
2.4.1 System LEDs
The system status LEDs indicate whether the PTM is receiving power from the chassis, and the
state of the PTM.
There are two system LEDs on the end of the module. The LED indications and meanings are
explained in the figure and table below.
Figure 5: Indicator LEDs
Table 3 - PTM states and LED configurations:
2.4.2 Port LEDs
The PTM has two I/O LEDs per port. The I/O LEDs are located on the I/O panel. The green LED,
when lit, indicates that the driver is running and a valid physical connection between nodes exists.
If the green LED is blinking, it indicates a problem with the physical link. The yellow LED when
lit, indicates a valid data activity link, this is the logical link. The yellow LED illuminates when the
network is discovered over the physical link. A valid data activity link without data transfer is des-
LED Module Status
Indication Status Power
OFF OFF OFF
OFF ON Boot in Progress
PTM not ready
Blinking Blue
BLINKING BLUE ON The CMC is identifying
the newly installed PTM
ON BLUE ON PTM is on and operating Normally
ON or BLINKING
AMBER
ON FW update is in progress or
Fault in System
Self-diagnosed
ON or BLINKING
AMBER
OFF Fault in System
CMC-detected
The IO Module is on and
ready when this LED is
green.
This LED can be blue or
amber. A fault is indicated
when the amber LED is blink-
ing. See Table 3.
Andere Handbücher für PowerEdge M420
13
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Dell Steuereinheit Handbücher
Dell
Dell PowerConnect W Series Bedienungs- und Wartungsanleitung
Dell
Dell LC-EJ-10GE-10P Bedienungsanleitung
Dell
Dell PowerEdge M420 Service-Handbuch
Dell
Dell MXG610s Bedienungsanleitung
Dell
Dell H955N Bedienungsanleitung
Dell
Dell PowerConnect W-6000M3 Bedienungsanleitung
Dell
Dell FC SAN Bedienungsanleitung
Dell
Dell PowerEdge FN Bedienungsanleitung
Dell
Dell K804N Bedienungsanleitung
Dell
Dell UPS 2700R Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
