Dell Precision Workstation 340 Bedienungsanleitung
DellPrecision™WorkStation340ServiceManual
Before You Begin
Safety First—For You and Your Computer
Protecting Against Electrostatic Discharge
Removing and Installing Parts
Computer Cover
Front Panel Door and Hinge Arms
Front-Panel Inserts
Inside Your Computer
System Board Components
Battery
Drives
Computer Memory
Expansion Card Cage (Small Desktop Computer Only)
Expansion Cards
I/O Panel
Control Panel
Chassis Intrusion Switch
Microprocessor
Power Supply
System Board
Notes, Notices, and Cautions
Information in this document is subject to change without notice.
©2003DellComputerCorporation.Allrightsreserved.
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Dell Precision are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation
disclaims any proprietary interest in trademarks and trade names other than its own.
March 2003 Rev. A02
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Back to Contents Page
Battery
DellPrecision™WorkStation340ServiceManual
The 3.0-V CR2032 coin-cell battery installed on the system board provides power to retain the configuration, date, and time information when the computer is
turned off. The computer battery is designed to provide years of service without being replaced. However, you may need to replace the battery if configuration
or clock-related inconsistencies occur or if one of the following messages is displayed during the boot routine:
Time-of-day not set -please run SETUP program
or
Invalid configuration information -
please run SETUP program
1. If you have not already done so, make a copy of your computer configuration information in system setup.
If the settings are lost while you are replacing the battery, you can refer to your copy of the computer configuration information to restore the correct
settings.
2. Turn off the computer and devices, disconnect them from their electrical outlets, and wait 10 to 20 seconds.
3. Open the computer cover.
4. Remove the battery.
To locate the battery on the system board, see your computer's illustration in "System Board Components."
Removing the Battery
Press in on the tab to release the battery.
5. Install the new battery.
Orient the battery with the side labeled "+" facing up. Then insert the battery into the socket, and snap it into place.
Installing the Battery
CAUTION: There is a danger of the new battery exploding if it is installed incorrectly. Replace the battery only with the same or equivalent type
recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
CAUTION: Before you perform this procedure, see "Safety First—For You and Your Computer."
NOTICE: Before disconnecting a device from the computer, wait 10 to 20 seconds after disconnecting the computer from its electrical outlet. Before
removing a component from the system board, verify that the standby power light on the system board has turned off. To locate this light, see your
computer's illustration in "System Board Components."
1
battery
2
battery socket
3
tab
6. Close the computer cover.
7. Reconnect the computer and devices to their electrical outlets, and turn them on.
8. Enter system setup and enter the current time and date. Then exit system setup and save the information.
For more information on entering system setup, see your User's Guide.
9. Turn off your computer and disconnect it from its electrical outlet. Leave the computer off for at least 10 minutes.
10. Reconnect the computer to its electrical outlet and turn it on.
11. Enter system setup, and check the date and time.
12. If the time and date are still incorrect, contact Dell for technical assistance.
Back to Contents Page
1
battery
2
battery socket
NOTE: If enabled, the Chassis Intrusion option will cause the following message to be displayed at the next computer start-up: ALERT! Cover was
previously removed.
Back to Contents Page
Chassis Intrusion Switch
DellPrecision™WorkStation340ServiceManual
Removing the Chassis Intrusion Switch
1. Turn off the computer and devices, disconnect them from their electrical outlets, wait at least 10 to 20 seconds, lay the mini-tower computer on its side,
and open the computer cover.
Small Desktop Computer
Small Mini-Tower Computer
2. Disconnect the chassis intrusion switch cable connector from the control panel on the front of the computer.
Note the routing of the chassis intrusion cable as you remove it from the computer. Hooks may hold the cable in place inside the computer.
3. Slide the chassis intrusion switch out of its slot and remove the switch and its attached cable from the computer.
CAUTION: Before you perform this procedure, see "Safety First—For You and Your Computer."
NOTICE: Before disconnecting a device from the computer or removing a component from the system board, verify that the standby power light on the
system board has turned off. To locate this light, see "System Board Components."
Replacing the Chassis Intrusion Switch
To replace the chassis intrusion switch, follow the "Removing the Chassis Intrusion Switch" procedures in reverse order.
Resetting the Chassis Intrusion Detector
1. Enter system setup by pressing <F2> during the computer's POST.
For instructions on using system setup, see the User's Guide.
2. Under the System Security tab, reset the Chassis Intrusion option by pressing the left-or right-arrow key to select Reset. Change the setting to
Enabled, Enabled-Silent, or Disabled.
3. Press <Alt><B> to restart the computer and implement your changes.
Back to Contents Page
NOTE: The default is Enabled-Silent.
NOTE: If a setup password has been assigned by someone else, contact the network administrator for information on resetting the chassis intrusion
detector.
Back to Contents Page
Computer Cover
DellPrecision™WorkStation340ServiceManual
Opening the Computer Cover
1. Turn off the computer and devices, disconnect them from their electrical outlets, and wait 10 to 20 seconds.
2. If you have installed a padlock through the padlock ring on the back panel, remove the padlock.
3. If you have a mini-tower computer, lay the computer on its side.
4. Press the two release buttons until the cover is free to swing up.
5. Raise the back of the cover, and pivot it toward the front of the computer.
Small Desktop Computer
Mini-Tower Computer
CAUTION: Before you perform this procedure, see "Safety First—For You and Your Computer."
NOTICE: Before disconnecting a device from the computer, wait 10 to 20 seconds after disconnecting the computer from its electrical outlet. Before
removing a component from the system board, verify that the standby power light on the system board has turned off. To locate this light, see your
computer's illustration in "System Board Components."
NOTE: On the small desktop computer, remove the stand before you open the computer cover. On the mini-tower computer, place the computer on its
side before you open the cover. See your User's Guide for more information.
NOTICE: Do not open the cover if the computer is on the edge of a desk or table. Doing so may cause the computer to tip over and fall. Make sure that
the computer is situated so that there is at least 12 inches of desk-or tabletop for the cover to rest on.
NOTICE: Open the cover slowly to ensure you do not damage any cables.
Closing the Computer Cover
1. Check all cable connections, especially those that might have come loose during your work. Fold cables out of the way so that they do not obstruct the
computer cover.
2. Ensure that no tools or extra parts (including screws) are left inside the computer.
3. Close the computer cover by pivoting the cover down toward the back of the computer and into position. Make sure that the release buttons click into
place.
Small Desktop Computer
Mini-Tower Computer
4. If you are using a padlock to secure your computer, install the padlock.
Back to Contents Page
Back to Contents Page
Control Panel
DellPrecision™WorkStation340ServiceManual
Removing the Control Panel
Desktop Computer
1. Remove the front I/O panel.
2. Using an 8-inch #2 Phillips screwdriver, remove the screw that secures the control panel to the computer, and lift the panel away from the computer.
Mini-Tower Computer
1. To remove the top and bottom panels of the computer, remove any installed CD drives and release all the tabs on each panel.
CAUTION: Before you perform this procedure, see the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE: Before you disconnect a device from the computer or remove a component from the system board, verify that the standby power light on the
system board has turned off. To locate the light, see "System Board Components."
2. To prepare the computer cover for removal, release the three computer cover tabs (one tab is located by the CD drive and two tabs are located by the
I/O panel).
3. If necessary, remove the computer cover screw.
4. Close the computer and remove the computer cover.
5. Remove the screw that secures the control panel to the computer, and pull the control panel away from the computer.
Replacing the Control Panel
Desktop Computer
Follow the steps in the "Removing the Control Panel" procedure in the reverse order, ensuring that all tabs are secure.
Mini-Tower Computer
Follow the steps in the "Removing the Control Panel" procedure in the reverse order, ensuring that all tabs are secure.
Back to Contents Page
1
computer cover tab (remove the CD drive to access this tab)
2
top-panel tabs
3
top panel
4
bottom panel
5
computer cover screw
6
computer cover tabs (2)
NOTE: To release the tab located by the CD drive, you can pry the computer cover away from the computer and pull out the tab.
Andere Handbücher für Precision Workstation 340
2
Inhaltsverzeichnis
Andere Dell Desktop Handbücher
Dell
Dell Precision 3460 Small Form Factor Bedienungsanleitung
Dell
Dell Dimension E520 Bedienungsanleitung
Dell
Dell XPS 8700 Bedienungsanleitung
Dell
Dell Inspiron 5720 Bedienungsanleitung
Dell
Dell Precision 3430 Bedienungsanleitung
Dell
Dell OptiPlex 3050 Bedienungsanleitung
Dell
Dell OptiPlex 5060 Tower Bedienungsanleitung
Dell
Dell Precision M6300 Bedienungsanleitung
Dell
Dell OptiPlex 5270 All-in-One Handbuch
Dell
Dell OptiPlex GX745 Bedienungsanleitung
Dell
Dell Inspiron 20 3000 Series Bedienungsanleitung
Dell
Dell Precision Workstation 390 Bedienungsanleitung
Dell
Dell Inspiron 620 Kurzanleitung
Dell
Dell Dimension 4600 Series Bedienungsanleitung
Dell
Dell Inspiron 24 3000 series Bedienungs- und Wartungshandbuch
Dell
Dell Vostro 470 Bedienungsanleitung
Dell
Dell Precision Workstation T1500 Betriebsanleitung
Dell
Dell OptiPlex N Bedienungsanleitung
Dell
Dell Inspiron 14 5415 Bedienungsanleitung
Dell
Dell Precision T3600 Betriebsanleitung
