Dell XPS 730 H2C Bedienungsanleitung

Dell™XPS™730/730XServiceManual

Model DCDO

Notes, Cautions, and Warnings

Information in this document is subject to change without notice.

©2008DellInc.Allrightsreserved.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and XPS are trademarks of Dell Inc.; Microsoft and Windows, are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

November2008Rev.A00

Technical Overview

Before You Begin

Replacing the Computer Stand

Replacing the Computer Cover

Replacing the Theater Lighting Unit

Replacing Memory Module(s)

Replacing a PCI/PCI Express Card

Replacing Drives

Replacing the Heat Sink Assembly

Replacing the Processor

Replacing Fans

Replacing the Master Control Board

Replacing the System Board

Replacing the Power Supply

Replacing the Battery

System Setup

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Before You Begin

Dell™XPS™730/730XServiceManual

Technical Specifications

Recommended Tools

Turning Off Your Computer

Safety Instructions

This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the

following conditions exist:

lYou have performed the steps in Turning Off Your Computer and Safety Instructions.

lYou have read the safety information that ships with your computer.

lA component can be replaced or—if purchased separately—installed by performing the removal procedure in reverse order.

Technical Specifications

For information on technical specifications of your computer, see the Quick

Reference Guide that shipped with your computer or see the Dell Support

website at support.dell.com.

Recommended Tools

The procedures in this document may require the following tools:

lSmall Phillips screwdriver

lSmall flat-blade screwdriver

Turning Off Your Computer



1. Shut down the operating system:



2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut

down your operating system, press and hold the power button for about 4 seconds to turn them off.

Safety Instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your own personal safety.



1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.



2. Turn off your computer (see Turning Off Your Computer).

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is

not covered by your warranty.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking

tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented

and aligned.

CAUTION: To avoid damaging the computer, perform the following steps before you begin working inside the computer.



3. Disconnect all telephone or network cables from the computer.



4. Disconnect your computer and all attached devices from their electrical outlets.



5. Press and hold the power button while the system is unplugged to ground the system board.



Back to Contents Page



CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back

of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal

components.

Back to Contents Page

Replacing a PCI/PCI Express Card

Dell™XPS™730/730XServiceManual

Removing a PCI Express Graphics Card From a Multi Graphics Card Configuration

Installing Graphics Cards for Multi Graphics Card

Replacing the PCI and PCI Express Cards



Removing a PCI Express Graphics Card From a Multi Graphics Card Configuration



1. Follow the procedures in Before You Begin.



2. Remove the computer cover (see Replacing the Computer Cover).



3. Gently securing both graphics cards with one hand, remove the graphics card bridge (if present) with your other hand by pulling it up and away from the

computer. Set it aside.

Repeat if removing two bridges from a triple card configuration.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTE: If a graphics card is installed in each of the PCIe x16 card slots in the multi-graphics configuration, the PCIe x1 and one PCI card slot are not

accessible for use.

PCI card

PCIe x1 card

PCIe x1 card slot

PCIe x16 card slot

PCIe x16 card



NOTE: This section deals with dual and triple configurations of PCIe x16 graphics cards only. For removal of any other type of PCI or PCIe cards, see

Replacing the PCI and PCI Express Cards.

graphics card bridge

power connectors (2)

dual-PCIe graphics cards



4. Disconnect any cables connected to the card.



5. Remove the captive screws on top of the PCI card fan shroud and remove the shroud.



6. Remove the card retention screw(s) on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis

wall.



7. Press the securing tab (if present) on the system board connector as you grasp the card by its top corners, and then ease the card straight out of the

connector



8. Install a filler bracket in the empty card-slot opening. If you are replacing the card, see Installing Graphics Cards for Multi Graphics Card.



9. Replace the PCI card fan shroud, replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical

outlets, and then turn them on.

Installing Graphics Cards for Multi Graphics Card

This section pertains to using dual and triple PCIe graphics cards to take advantage of NVIDIA's SLI (Scalable Link Interface). For installation of other types of

PCI or PCIe cards, see Replacing a PCI/PCI Express Card.

retention screw

card retainer

alignment guide

fan bracket

PCIe x16 card

securing tab

PCIe x16 card slot



NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep

dust and dirt out of your computer.

NOTE: The graphics card bridge (not present in all multi-graphics configurations) is not necessary in a single graphics card configuration.

CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

NOTE: To upgrade to or downgrade from a dual-or triple-graphics card configuration, you may need additional parts that can be ordered from Dell.

Some expansion card slots will not be available for use if a dual-slot graphics card is installed in any of the PCIe x16 card slots. If you are upgrading from a

single-slot graphics card to a dual-slot graphics card, you will need to remove any card installed in these expansion slots. To remove a PCIe card, see

Replacing the PCI and PCI Express Cards.



1. Follow the procedures in Before You Begin.



2. Remove the computer cover (see Replacing the Computer Cover).



3. Remove the captive screws on top of the PCI card fan shroud and remove the shroud.



4. Remove the filler bracket or existing graphics card to create a card-slot opening.



5. Install two SLI-ready graphics cards into the two outer PCIe x16 slots on the system board.



6. Prepare the cards for installation.

See the documentation that came with the cards for information on configuring them, making internal connections, or otherwise customizing them for

your computer.



7. Position each card so that it is aligned with the slot and that the securing tab (if present) is aligned with the slot.



CAUTION: For information about upgrading your system to use NVIDIA SLI (Scalable Link Interface) multi-graphics technology, see the Dell

support website at support.dell.com.

NOTE: If you are upgrading to a multi-graphics card configuration and have a card installed in the PCIe x1 card slot, remove the card (see

Replacing the PCI and PCI Express Cards).

retention screw

card retainer

alignment guide

fan bracket

NOTE: If the card is full length, insert the card guide into the alignment slot on the fan bracket.

PCIe x16 card

securing tab

PCIe x16 card slot



CAUTION: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.

Gently pull the securing tab (if present) and place the card in the connector. Press down firmly and ensure that the card is fully seated in the slot.



8. Screw in the card retention screw(s) on the top of the card retainer at the appropriate card slot.



9. Repeat for additional graphics cards.

Connect the PCIe supplementary power connectors from the system power supply to each of the graphics cards. See the documentation for the card for

information about the card's cable connections.



10. Install the NVIDIA SLI connector across the two outer graphics cards. Each SLI-ready graphics card has an SLI connector tab on its upper side. Press

firmly on each connector so that it completely covers the connector tab.



11. If present, lower the graphics card bridge that lays over the installed cards and snap it into place.



12. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.

Replacing the PCI and PCI Express Cards



1. Follow the procedures in Before You Begin.



2. Remove the computer cover (see Replacing the Computer Cover).



3. Disconnect any cables connected to the card.



4. If the card is a full length, remove the captive screws on top of the PCI card fan shroud and remove the shroud.



5. Remove the card retention screw.

CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

CAUTION: An incorrectly attached graphics power cable may result in degraded graphics performance.

graphics card bridge

power connectors (2)

dual-PCIe graphics cards



CAUTION: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface on the computer chassis.

CAUTION: If your computer came with a PCI graphics card installed, removal of the card is not necessary when installing additional graphics

cards; however, the card is required for troubleshooting purposes. If you remove the card, store it in a safe and secure location.



6. Press the securing tab (if present) on the system board connector as you grasp the card by its top corners, and then ease the card out of the

connector.



7. Install a filler bracket in the empty card-slot opening. If you are replacing the card, see Replacing a PCI/PCI Express Card.



8. Reinstall the card retention screw.



9. Reinstall the card slot fan shroud.



10. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.



11. Uninstall the driver for the card that you removed.



12. If present, press the tab on the graphics card bridge that lays over the installed cards and rotate it upwards to gain full access to the card.



13. Press down the tab on the top of the graphics card bridge at the appropriate card slot and pivot the graphics card bridge back through the chassis wall.

retention screw

card retainer

alignment guide

fan bracket

NOTE: If the card is full length, press the securing tab on the end of the alignment guides on the fan bracket.

PCIe x16 card

securing tab

PCIe x16 card slot



NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep

dust and dirt out of your computer.

CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

CAUTION: If you have or are upgrading to the optional multi-graphics configuration, see Installing Graphics Cards for Multi Graphics Card to

install a graphics card.



14. Remove the filler bracket or existing card (see Replacing the PCI and PCI Express Cards) to create a card-slot opening.



15. Prepare the card for installation.

See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your

computer.



16. Position the card so that it is aligned with the slot and the securing tab (if present) is aligned with the slot.



17. Gently pull the securing tab (if present) and place the card in the connector. Press down firmly and ensure that the card is fully seated in the slot.

retention screw

card retainer

alignment guide

fan bracket

NOTE: If the card is full length, insert the card guide into the alignment slot on the fan bracket.

PCIe x16 card

securing tab

PCIe x16 card slot



CAUTION: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.



18. Connect any cables that should be attached to the card.

See the documentation for the card for information about the card's cable connections.



19. Rotate the graphics card bridge back into its original position; push its tip so that its tab clicks into place.



20. If present, lower the graphics card bridge that lays over the installed cards and snap it into place.



21. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.



22. Install any drivers required for the card as described in the card documentation.

Back to Contents Page



card connector (seated)

card connector (not seated)

bracket properly aligned within

slot

bracket improperly aligned outside of

slot

alignment bar

alignment guide

CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

CAUTION: An incorrectly attached graphics power cable may result in degraded graphics performance.

CAUTION: Before rotating the card retainer back into place, ensure that the tops of all cards and filler brackets are flush with the alignment bar

and the notch in the top of each card or filler bracket fits around the alignment guide.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Desktop Handbücher

Dell

Dell Vostro 410 Bedienungsanleitung

Dell

Dell GX240 - OptiPlex Pentium 4 1.8GHz 512MB 40GB CD... Bedienungsanleitung

Dell

Dell Inspiron 20 Bedienungsanleitung

Dell

Dell Dimension 3100C Bedienungsanleitung

Dell

Dell Precision Workstation 530 Bedienungsanleitung

Dell

Dell OptiPlex 3240 Bedienungsanleitung

Dell

Dell OptiPlex 960 Betriebsanleitung

Dell

Dell OptiPlex 5060 Tower Bedienungsanleitung

Dell

Dell Vostro 360 Bedienungsanleitung

Dell

Dell Precision Workstation 350 Bedienungsanleitung

Dell

Dell OptiPlex GX100 Bedienungsanleitung

Dell

Dell OptiPlex 9020 Bedienungsanleitung

Dell

Dell Precision PD055 Bedienungsanleitung

Dell

Dell OPTIPLEX 740 Systemhandbuch

Dell

Dell OptiPlex R9730 Bedienungsanleitung

Dell

Dell XPS 8920 Bedienungs- und Wartungshandbuch

Dell

Dell OptiPlex W6987 Bedienungsanleitung

Dell

Dell OPTIPLEX 9010 ALL-IN-ONE Bedienungsanleitung

Dell

Dell Dimension 06Y490A01 Bedienungsanleitung

Dell

Dell OptiPlex 980 - Desktop Bedienungsanleitung

Dell

Dell Precision Workstation T1500 Bedienungsanleitung

Dell

Dell OptiPlex 5080 Micro Bedienungsanleitung

Dell

Dell Vostro 3070 Handbuch

Dell

Dell XPS 700 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung

Lenovo

Lenovo IdeaCentre A540-24ICB Betriebsanleitung