Dell P Series Gebrauchs- und Pflegehandbuch
Firmware Update Instruction User's Guide | 1
Firmware Update Instruction User's Guide
Overview
Firmware update tool is an application used to update monitor firmware.
Firmware Update Pre-requisites
1The monitor must be connected to a power source during the firmware updating process.
2Make sure there is only ONE video input source, e.g. DisplayPort, HDMI, or USB Type-C,
from the computer to the monitor.
NOTE: Ensure that all other video cables between the monitor and the computer are
unplugged.
2| Firmware Update Instruction User's Guide
3Connect the USB upstream cable or USB Type-C cable directly between the monitor and
your computer. Do not use any other device between this connection.
USB Type-C
USB Type-A
or
NOTE: Ensure that other USB cables and USB devices between the monitor and the
computer are unplugged.
NOTE: Disconnect all other monitors from the notebook or desktop. This will ensure that
only one display is connected while conducting firmware update.
NOTE: It is recommended to update the firmware with a notebook as the monitor screen
may go blank during the firmware update process.
NOTE: Do not unplug the USB upstream cable or USB Type-C cable till the updating
process finishes.
NOTE: Please disable sleep mode before you launch the firmware update.
NOTE: Update one monitor at a time. Do not conduct firmware update on multiple
monitors at a given time.
Firmware Update Instruction User's Guide | 3
Installation
Install via GUI
1Double-click deb file (e.g. Dell_P3424WE_FWUpdate_M2B102_Ubuntu.deb) on the
desktop and then click the Install button in Ubuntu software center.
4| Firmware Update Instruction User's Guide
2Execute firmware update tool via Ubuntu desktop.
3Initializing for device status.
Firmware Update Instruction User's Guide | 5
4The utility will load the firmware file automatically. Or, you can select your file manually by
clicking and navigating to the UPG firmware file.
5Click Update. The utility will start updating the new firmware.
6| Firmware Update Instruction User's Guide
6Once the updating process is completed, please follow the on-screen instructions to re-
start your monitor.
NOTE: Update takes up to 12 minutes. Do not power off or disconnect cable while
updating.
NOTE: If you experience problems during or after update, refer to
Troub l e sho oti ng
.
Install via Command
1Copy deb file (e.g. Dell_P3424WE_FWUpdate_M2B102_Ubuntu.deb) to the desktop.
2Open the terminal and input command.
sudo dpkg -i filename
(e.g. sudo dpkg -i ~/Desktop/ Dell_P3424WE_FWUpdate_M2B102_Ubuntu.deb)
Firmware Update Instruction User's Guide | 7
3Execute firmware update tool via Ubuntu desktop.
4Initializing for device status.
8| Firmware Update Instruction User's Guide
5The utility will load the firmware file automatically. Or, you can select your file manually by
clicking and navigating to the UPG firmware file.
6Click Update. The utility will start updating the new firmware.
Firmware Update Instruction User's Guide | 9
7Once the updating process is completed, please follow the on-screen instructions to re-
start your monitor.
NOTE: Update takes up to 12 minutes. Do not power off or disconnect cable while
updating.
NOTE: If you experience problems during or after update, refer to
Troub l e sho oti ng
.
Uninstall
1Open the terminal and input command.
sudo dpkg -P dell-monitor-firmware-update-utility
Errors Possible Solutions
File permission error •Try saving the firmware file in another location.
•Check if the firmware file has read permission.
•Check if you have owner rights for the firmware file.
•Or, run this utility with administrator privileges.
Monitor not detected •Follow
Firmware Update Pre-requisites
to check if the power and USB
cables are properly connected to your computer and reopen the Monitor
Firmware Update Utility.
•In USB of the OSD menu, make sure the USB port is set to the
corresponding input signal.
Write protection error Re-try updating with the following steps:
Flash erase error
Update error
Monitor firmware checksum
error
USB device inactive after
new firmware installation.
Re-try the updating steps from 1 to 4 as stated above.
A warning message appears:
“Firmware update was not
completed. Please update
the monitor firmware again.”
Re-try updating the monitor’s firmware. Do not turn off the ISP tool until the
update is complete.
10 | Firmware Update Instruction User's Guide
Tro ub l eshooting
1Close the Monitor Firmware Update Utility.
2Turn off the monitor by pressing the power button.
3Re-plug the power cord.
4Turn on the monitor.
5Try updating again with the Monitor Firmware Update Utility.
Andere Handbücher für P Series
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Dell Monitor Handbücher
Dell
Dell UltraSharp U2913WM Bedienungsanleitung
Dell
Dell UP2720QA Gebrauchsanweisung
Dell
Dell UltraSharp U2412M Bedienungsanleitung
Dell
Dell P2210H Bedienungsanleitung
Dell
Dell E1920H Gebrauchsanweisung
Dell
Dell E1910 - 19" LCD Monitor Bedienungsanleitung
Dell
Dell E1910 - 19" LCD Monitor Bedienungsanleitung
Dell
Dell 1908WFP - UltraSharp - 19" LCD Monitor Bedienungsanleitung
Dell
Dell P2012H Technisches Datenblatt
Dell
Dell UltraSharp 27 Bedienungsanleitung
Dell
Dell S2216H Bedienungsanleitung
Dell
Dell E1709W Bedienungsanleitung
Dell
Dell P1914S Bedienungsanleitung
Dell
Dell 2709WFP Bedienungsanleitung
Dell
Dell IN2010NWFP Bedienungsanleitung
Dell
Dell U2410 - UltraSharp - 24" LCD Monitor Bedienungsanleitung
Dell
Dell ST2210 - 16:9 Aspect Ratio Flat Panel... Bedienungsanleitung
Dell
Dell 2707WFP - UltraSharp - 27" LCD Monitor Bedienungsanleitung
Dell
Dell C5522QT Bedienungsanleitung
Dell
Dell P3223DE Bedienungsanleitung
