Dell P2319H Montageanleitung
Wedge your fingers between the rear cover and the
middle bezel on the corners of the top side of the
monitor to release the rear cover, then use one hand
to press the middle bezel, the other hand to pull up
carefully the rear cover in order of arrow preference
for unlocking mechanisms of rear cover..
Use a Philips-head screwdriver to remove four
screws for unlocking mechanisms.
(No.1~4 screw size=M4x10; Torque=12±0.5kgfxcm)
S5
Take out all of the QSG,accessories including DP
cable, power cable, USB cable, CD&user’s manual,
stand and base from the carton from the
carton.(Note: It depends on whether users returning
the accessories)
S2
Open the Pizza carton with a proper tool.
1. Disassembly Procedures:
Lift the rear cover up carefully. Disconnect the USB
FFC cable from the connector of the interface board,
and then remove the rear cover.
S6
S4
S1
Take out of the Paper-top and monitor from the
carton, then take out the monitor from the EPE bag
and put the LCD monitor on a protective cushion.
S3
23
41
1
Go to contents page
DELL P2319H
QSG
stand
base
power cable
DP cable
USB cable
user’s manual
3
1
2
4
Tear off two pieces of the aluminium foils for unfixing
the bracket chassis base.
S8
Use a proper tool to release the function key cable
from the connector, then pull the function key cable
high for releasing the function key cable.
S9
Use a Philips-head screwdriver to remove one screw
for unlocking the USB board unit, then release the
USB board unit and put it aside.
(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
S7
2
Go to contents page
DELL P2319H
Unplug the panel power cable from the connector of
the panel module, then release the function by
tearing the tapes on the back of the cable, and then
release the cable from the hooks of the middle
bezel.
Use a Philips-head screwdriver to remove 2pcs
screws for unlocking the bracket with the panel.
Push the earing-lock, and disconnect the LVDS
cable from the connector of LCD panel module.
(No.1~2 screw size=M3x2.8, Torque=2~3kgfxcm)
S10
S11
S12
S13
1
aluminum foil
aluminum foil
Use a Philips-head screwdriver to remove 13pcs
screws for unlocking the middle bezel with the
assembled unit.
(No.1~11 screw size=M3x4, Torque=3~4kgfxcm;
No.12~13 screw size=M1.6x1.7, Torque=0.6~1kgfxcm)
2
10
41
11
3
8
6
5
9
7
12 13
21
31
2
Take away the
.
middle bezel, and put it on a fixture,
then use a Philips-head screwdriver to remove 3pcs
screws for unlocking the function key board with the
middle bezel
Take away the bracket chassis module and then put
the bracket chassis module on a protective cushion.
S15
Use a Hex-head screwdriver to remove two screws
for unlocking the D-Sub connector.
(No.1~2 screws size=M3x8, Torque=6±0.5kgfxcm)
( No.3~4 screw size=M3x8, Torque=6~7kgfxcm)
Use a Philips-head screwdriver to remove
screws for unlocking the AC power outlet.
two
Remove the interface board and power board from
the bracket chassis module carefully, and disconnect
all the cables.
Remove the Mylar from the hooks of the bracket.
Use a Philips-head screwdriver to remove six screws
for unlocking the circuit board, release all the cables
from the hooks.
(No.1~5 screw size=M3x7.5, Torque=6±0.5kgfxcm;
No. 6 screw size=M4x8, Torque=6±0.5kgfxcm)
S17
Lift up the panel module for releasing the front bezel
away from the panel module.
S14
S16
S18
3
Go to contents page
DELL P2319H
34
6
25
1
21
43
Remove electrolyte capacitors (red mark) from printed circuit boards
S1ϵ-1 Cut the glue between bulk cap. and PCB with a knife
S1ϵ-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB
S1ϵ-3 Cut into the bottom of bulk cap. and pull it up carefully
4
S19
DELL P2319H
S1ϵ-4 Take out bulk cap. pin solder with soldering iron and absorber
S1ϵ-5 Lift the bulk cap. up and away from the PCB
5
DELL P2319H
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU Council
Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components
No used
Batteries
No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and
liquids
No used
Plastic containing BFR
No used
Component and waste contain
asbestos
No used
CRT
No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps
No used
LCD display > 100 cm2
Product has an LCD greater than 100 cm2
External electric cable
Product has external cables
Component contain refractory
ceramic fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors (height >
25mm, diameter > 25mm)
ϯ. Tools Required
List the type and size of the tools that would typically can be used to disassemble the
product to a point where components and materials requiring selective treatment
can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
Ϯ. Product material information
6
DELL P2319H
Andere Handbücher für P2319H
1
Andere Dell Monitor Handbücher
Dell
Dell UltraSharp 1908FP-BLK Bedienungsanleitung
Dell
Dell S2817Q Bedienungsanleitung
Dell
Dell S2230MX Bedienungsanleitung
Dell
Dell S2422HZ Bedienungsanleitung
Dell
Dell E770S - 17" CRT Display Bedienungsanleitung
Dell
Dell UltraSharp U2515H Bedienungsanleitung
Dell
Dell U2718QM Bedienungsanleitung
Dell
Dell E1910H - 19" LCD Monitor Bedienungsanleitung
Dell
Dell Professional P2412H Bedienungsanleitung
Dell
Dell SP2009W Bedienungsanleitung
Dell
Dell E228WFPc Bedienungsanleitung
Dell
Dell 1708FP - UltraSharp - 17" LCD Monitor Bedienungsanleitung
Dell
Dell S2240Tb Bedienungsanleitung
Dell
Dell P3424WE Bedienungsanleitung
Dell
Dell UltraSharp U2515HX Bedienungsanleitung
Dell
Dell 2407WFP-HC - UltraSharp - 24" LCD Monitor Bedienungsanleitung
Dell
Dell E2423HN Bedienungsanleitung
Dell
Dell P2210H Bedienungsanleitung
Dell
Dell E248WFP - 24" LCD Monitor Bedienungsanleitung
Dell
Dell P4317Q Bedienungsanleitung
