Dell S560T Bedienungsanleitung
Dell | Interactive Projector
S560T
Touch Setup Guide
S560T Laser Touch QSC_A00.book Page 1 Wednesday, June 22, 2016 2:39 PM
About Notes
NOTE: A NOTE indicates important information that helps you make better use of your
projector.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or
death.
__________________
Information in this document is subject to change without notice.
© 2016 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of
Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Microsoft,
Windows 7, and Windows Vista are trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in
trademarks and trade names other than its own.
June 2016
S560T Laser Touch QSC_A00.book Page 2 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
3
Usage Notice
Please follow all warnings, precautions and
maintenance as recommended in this user's
manual.
WARNING: Do not disassemble Touch
Unit.
WARNING: Do not use, store, or leave the
Touch Unit near fire, or in places with a
high temperature, e.g., in direct sunlight,
or in sun-heated cars.
WARNING: Use standard USB cable
(maximum length: 0.2 inch (5 m )). To
extend USB cable length over 5m, a
certified active extension USB cable is
required.
WARNING: Do not allow liquids or foreign
materials enter the Touch Unit.
Precautions
The Infrared (IR) camera on the projector
receives infrared signal from the Touch Unit
which is attached to the whiteboard.
To operate normally:
• The IR camera should face the
projected image area on the wall.
• Remove any obstacle in between IR
camera and Touch Unit.
• Do not place other infrared
communication devices, such as IR
microphone; lighting equipments; or
residential heating equipments etc,
nearby.
• Use only the interactive cable from the
accessory kit, with the L side connector
plugged into the Touch Unit.
Maintenance: Gently clean the optical port with
a dust blower.
Set Up Touch on Your Projector
S560T Laser Touch QSC_A00.book Page 3 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
4
How it works
• The Touch Unit covers the entire
whiteboard with a thin invisible IR light.
• When a finger or stylus breaks into the
light curtain, the IR light reflects on to
the IR camera.
• The camera module tracks multiple
touch points and reports the positions
to a computer via USB.
• To optimize the touch function, the
screen non-flatness should be less than
0.2 inch (5 mm).
S560T Laser Touch QSC_A00.book Page 4 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
5
Specifications
I. Touch Unit (S560T Only)
Laser Safety Class 1
Touch Unit to Screen Distance 0.79 inch ~3.94 inch (20 mm~100 mm) @81"~100" 1080p
LED Indicator Blue/Red
I/O Port Interactive Jack x1
Touch sensor adjustment 2-knob adjustment and with visible light
ID Size(W*L*H) 5.91 (W) x 1.97 (L) x 1.57 (H) inch
(150.0 (W) x 50.0 (L) x 40.0 (H) mm)
Weight < 330 g
Power Consumption 12V/0.3A
Operation Temperature 0 °C~+40 °C (without cooling fan)
Storage Temperature -20 °C~+60 °C
II. General Specifications
Screen Non-flatness <0.2 inch (5 mm)
S560T Laser Touch QSC_A00.book Page 5 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
6
Display mode Supports ceiling mode only
Calibration 1. Manual Calibration :
9 points manual calibration ,
1080p model: +/- 6 pixels (screen non-flatness <0.2 inch
(5mm))
2. Auto calibration :
1080p model:+/- 8 pixels (screen non-flatness <0.2 inch
(5mm))
3. Supports one-key calibration
Aspect ratio correction Auto- calibration to different display resolutions and aspect
ratios
Multi-touch Windows 7/8/10: 10 touch points
Mac : Single-point touch
ChromeBook: 10 touch points
Multi-touch Min. Distance ≥1.57 inch (40mm)
Trouble Shooting Viewer Utility support real-time image for trouble shooting.
Working Projection Image Size 81"~100" @1080P(co-operate with S560T projector)
S560T Laser Touch QSC_A00.book Page 6 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
7
*1 : Get S560x Interactive Utility from provided CD or download it from Dell Support
*2 : S560T requires first-time alignment and calibration, ensure you complete setup process
before use
*3 : .NET Framework 4.0 installation is required
*4 : Mac OS support 1 touch point only
III. OS requirement
System Requirements Processor Type Intel Core™ i3 (or above) or same level of
AMD Core.
RAM 2 GB or More
Operating
System
Number of touch
points supported
Installation of S560x Interactive Utility*1
For first-time setup*2 For subsequent use
Windows 7/8/10 10 touch points Supported*3 Not required
Mac OS X
(10.7-10.11)
1 touch point*4 Supported Required, please install the
setup utility on all Mac OS
computers, to use them
with the S560T
Chromebook 10 touch points Not supported, please use a
Windows OS or Mac OS
computer to complete first-
time setup for the S560T
Not required
S560T Laser Touch QSC_A00.book Page 7 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
8
Step 1: Environment Check
A Make sure the projector is installed under
the following conditions:
-The wall should be strong enough to avoid
projection image flickering.
-Do no install the projector or screen in a
location subject to direct sunlight. If the
projector or the screen is subjected to
direct sunlight, the interactive function
may not operate correctly.
-The surface shall be suitable for the Touch
Unit to be secured with screws.
-The projection image on screen must be
sharp and visible with no light reflections
or hot spots.
-The screen surface should be flat, non-
flatness less than 0.2 inch (5mm). The
surface can either be a flat wall or a
whiteboard. For details on how to check
surface flatness see page 10.
-Keep at least 2 inch (50 mm) clearance
boundary of the projection image to avoid
reflection interference.
-Other IR devices are not allowed because
they will interfere the touch function. For
example, IR microphone.
-Use standard USB cable with a maximum
length of 16.4 ft (5 m). If the USB cable is
longer than 16.4 ft (5 m), a USB Hub or a
certificated active extension USB cable is
required.
-The projected image is a rectangular
shape.
If the projection surface meets the criteria
above, the Touch Unit can then be installed in
one of the following ways
1Mount the Touch Unit on a whiteboard.
S560T Laser Touch QSC_A00.book Page 8 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
9
2Mount the Touch Unit on a wall surface.
NOTE: The Touch Unit must be mounted
on the same surface as the projected
image.
B S560T Whiteboard size guidance
When mounting the Touch Unit on a
whiteboard please follow the guidelines below:
C Measuring projection surface flatness
-Criteria: overall whiteboard flatness <0.2
inch (5 mm), flatness requirement is <0.12
inch (3 mm) at Touch Unit mounting area.
-Equipment: leveling instrument 3.94~4.92
Ft (1.2~1.5 m) and thickness gauge.
D-1) Split projection area into 16 segments
equally as below chart. Place leveling
instrument on whiteboard.
Spaces of a & b are reserved to cater
for touch unit.
• Dimension a = 50 mm
• Dimension b = 77 mm
* inch [mm]
S1 W1 W2
81.0 [2057] ≥ 44.7 [1136] ≥ 74.5 [1893]
85.0 [2159] ≥ 46.7 [1186] ≥ 78.0 [1982]
89.1 [2263] ≥ 48.7 [1237] ≥ 81.6 [2073]
90.0 [2286] ≥ 49.1 [1248] ≥ 82.4 [2092]
95.0 [2413] ≥ 51.6 [1310] ≥ 86.7 [2203]
100.0 [2540] ≥ 54.0 [1372] ≥ 91.1 [2314]
1080p (16:9) image
S560T Laser Touch QSC_A00.book Page 9 Wednesday, June 22, 2016 2:39 PM
Set Up Touch on Your Projector
10
D-2) Insert 0.2 inch (5mm) thickness gauge at
point 1~9 positions in the following order:
Horizontal:
-Measure point 1, 2 & 3.
-Measure point 4, 5 & 6.
-Measure point 7, 8 & 9.
Vertical:
-Measure point 1, 4 & 7.
-Measure point 2, 5 & 8.
-Measure point 3, 6 & 9.
D-3) If 0.2 inch (5 mm) thickness gauge cannot
be inserted, it means whiteboard flatness
is less than 0.2 inch (5 mm) and capable
for finger touch.
Step 2: Installing the Touch
Unit
1Open top cover by Phillips screwdriver
(model: number 1).
2Mount base plate to whiteboard or wall.
Keep distance to image area:
-2.17~5.31 inch (55~135 mm) from bottom
of the base plate
S560T Laser Touch QSC_A00.book Page 10 Wednesday, June 22, 2016 2:39 PM
Inhaltsverzeichnis
Andere Dell Projektor Handbücher
Dell
Dell 3400MP - XGA DLP Projector Bedienungsanleitung
Dell
Dell S320 Bedienungsanleitung
Dell
Dell 1210S - DLP Projector - 2500 ANSI Lumens Bedienungsanleitung
Dell
Dell S320 Bedienungsanleitung
Dell
Dell 1609WX - WXGA DLP Projector Bedienungsanleitung
Dell
Dell S510 Bedienungsanleitung
Dell
Dell 2400MP - XGA DLP Projector Bedienungsanleitung
Dell
Dell M318WL Bedienungsanleitung
Dell
Dell S520 Bedienungsanleitung
Dell
Dell 1800MP Bedienungsanleitung
Dell
Dell 3300MP Bedienungsanleitung
Dell
Dell 4320 Bedienungsanleitung
Dell
Dell M210X Bedienungsanleitung
Dell
Dell 2400MP - XGA DLP Projector Bedienungsanleitung
Dell
Dell S520 Kurzanleitung
Dell
Dell 1409X Bedienungsanleitung
Dell
Dell S520 Bedienungsanleitung
Dell
Dell M110 Bedienungsanleitung
Dell
Dell S510 Bedienungsanleitung
Dell
Dell 1100MP Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
